User's Manual

Installation Manual

One- and Two-Channel RF Receivers

The SK-910RBQ and SK-910RB2Q are wireless receivers that meets the growing demand for

receivers with multiple and independently controlled output functions. These RF receivers are

compatible with both code hopping and fixed code transmitters (see page 4 of this manual for a list of

compatible transmitters). The receivers can be used to control a variety of home automation devices

such as garage door openers, lights, motorized gates, lifts, or other devices remotely.

WARRANTY This SECO-LARM product is warranted against defects in material and

workmanship while used in normal service for a period of one (1) year from the date of sale to the

original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any

defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if

damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,

repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason

SECO-LARM determines that such equipment is not operating properly as a result of causes other

than defects in material and workmanship. The sole obligation of SECO-LARM, and the purchaser’s

exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no

event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or

property damages of any kind to the purchaser or anyone else.

1. Mount the receiver out of sight in a location where it is not exposed to weather or moisture, and

where it is not surrounded by metal. Metal will block the RF signal, resulting in a reduced range.

2. For best range, pull the antenna wire as long and straight as possible. If the receiver receives

interference from local RF activity (e.g., an airport or military base), the antenna wire can be folded.

IMPORTANT: DO NOT CUT THE ANTENNA WIRE.

Installation Notes:

Introduction:

SK-910RBQ (315MHz)

SK-910RB-4Q (433.92MHz)

SK-910RB2Q (315MHz)

SK-910RB2-4Q (433.92MHz)

 Flexible operating voltage: 11~24 VAC/VDC

 Up to 500ft (152m) range

 Independently programmable channels

Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.

SK-910RB2Q shown

PAGE 1
Installation Manual SK-910RBQ (315MHz) SK-910RB-4Q (433.92MHz) SK-910RB2Q (315MHz) SK-910RB2-4Q (433.92MHz) SK-910RB2Q shown One- and Two-Channel RF Receivers  Flexible operating voltage: 11~24 VAC/VDC  Up to 500ft (152m) range  Independently programmable channels Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
PAGE 2
ENFORCER Two-Channel RF Receiver Code Learning a New Transmitter Button: Each receiver channel can learn the codes of up to 15 different transmitters on a first-in, first-out basis. Below is the procedure for code learning a new transmitter button. 1. Press the channel mode switch of the desired channel for 3 seconds or more. The channel’s LED will start to flash quickly to indicate that it is in learning mode. 2. While the LED is flashing, press the button of the transmitter to be learned one time.
PAGE 3
ENFORCER Two-Channel RF Receiver Overview: Channel 1 mode switch Channel 2 mode switch (SK-910RB2Q only) LP3 antenna program loop 3-Pin antenna port CH 1 CH 2 Channel Function Switches  Brown function switch is for channel 1 programming.  Red function switch is for channel 2 programming. SK-910RB2Q shown. SK-910RBQ is the same, but only has one each: mode switch; function switch; indicator LED; channel relay. COM N.C. Ch 2 relay (SK-910RB2Q only) N.O. COM N.C. Ch 1 relay Ch 1 indicator LED N.O.
PAGE 4