User's Manual

ManualsBrandsSuperior Electronics ManualsElectronicsRemote Control Transmitter

ENFORCER Wireless Request-to-Exit Plates

4 SECO-LARM U.S.A., Inc.

1. Remove the 2 screws from the front of the plate and remove the plate from the back-box.

2. Remove the battery clip from the 9V battery and remove the battery from the bracket.

3. Place the new battery in the bracket and snap the battery clip to the new battery.

4. Test the unit with the new battery. The LED should illuminate blue.

5. Put the plate back in the housing and secure it to the back-box using the screws on the front.

Troubleshooting:

LED is red

• 9V battery is low, replace with new one

LED does not light

• Check battery connection

• Replace 9V battery

LED lights blue, but does not

activate lock

• Check to make sure wireless request-to-exit plate is not housed in a

metal box

• Test wireless request-to-exit plate closer to the receiver

• Clear codes from receiver, and re-learn wireless plate transmitter code

Detail: Wireless Request-to-Exit Plates

Dimensions:

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or

the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF

exposure requirements and void user’s authority to operate the device.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

PITSW1 mi-SD-8XXX.doc

Switch

9V Alkaline

Battery

LED indicator

Request

button

Battery

clip

Wireless

transmitter

8202GT

PEQ

shown

Red=Low Battery

”

(38mm)

”

(114mm)

”

(70mm)

”

(57mm)

Red=L ow Batt ery

ENFO RCER

NOTE: Products with a model number that ends with “Q” or have a round green “Q” sticker represent RoHs compliant products.

ENFORCER

MANUAL

SK-910RQ / SD-8202GT-PEQ

System

These RF receivers are compatible with both code hopping and fixed-code transmitters+. They can be used for a variety

of applications, such as allowing the same transmitter to arm/disarm a vehicle alarm and open/close a garage door

opener. The receivers come in one- or two-channel versions. Each channel can learn the codes of up to 15 different

transmitter buttons on a first-in, first-out basis.

The ENFORCER Wireless RF Request-to-Exit Buttons are the ideal solution for difficult Access Control installations. The

RTE plates combine the very best of SECO-LARM, flexible wireless solutions and reliable access control. The RTE plates

are perfect for cement or brick walls, or any other location where it is difficult to run wires.

Features:

• Wireless RTE Plate Tx:

Range up to 250 feet. 315MHz.

Over 68 billion (6.8x10

) possible codes.

LED to indicate transmission and low battery.

• Stainless-steel single-gang or slim-line plate.

• RF Receiver:

Range up to 250 feet. 315MHz

Memory Capacity: 15 transmitter button codes per

channel

Relay Contact Rating: Form ‘C’ type; 10A @ 24VDC

or 120VAC per channel

Installation

1. Mount the receiver out of sight in a location where it is not surrounded by metal, and where it is not exposed to the

weather or moisture. Metal will block the RF signal, resulting in a reduced range.

2. For best range, pull the antenna wire of the receiver as long and straight as possible. If the receiver receives

interference from local RF activity (e.g.., airport or military base), the antenna wire can be folded. DO NOT CUT THE

ANTENNA WIRE.

3. Find a suitable location for the wireless request-to-exit plate.

NOTE: Do not house the plate in a metal box, this will greatly reduce the range.

NOTE: Do not house the plate in a metal box, this will greatly reduce the range.NOTE: Do not house the plate in a metal box, this will greatly reduce the range.

NOTE: Do not house the plate in a metal box, this will greatly reduce the range.

4. The wireless request-to-exit plate can be either surface mounted or flush mounted.

5. Test the operation of the wireless request-to-exit plate in the location where it will be installed.

NOTE: The wireless request

NOTE: The wireless requestNOTE: The wireless request

NOTE: The wireless request-

-to

toto

to-

-e

procedure.

procedure.procedure.

procedure.

6. Check and make sure the battery clip is securely connected. Then mount the wireless request-to-exit plate in the

back-box and secure it with the 2 included screws.

SECO-LARM

Summary of content (2 pages)

PAGE 1
ENFORCER Wireless Request-to-Exit Plates 1. Remove the 2 screws from the front of the plate and remove the plate from the back-box. ENFORCER 2. Remove the battery clip from the 9V battery and remove the battery from the bracket. 3. Place the new battery in the bracket and snap the battery clip to the new battery. 4. Test the unit with the new battery. The LED should illuminate blue. ® 5. Put the plate back in the housing and secure it to the back-box using the screws on the front.
PAGE 2
ENFORCER Wireless Request-to-Exit Plates ENFORCER Wireless Request-to-Exit Plates Learning a New Button Code into Receiver (channel 1) 1. Press receiver mode switch #1 for three seconds. The green LED will start to flash quickly. 2. While the green LED is flashing quickly, press SD-8202GT-PEQ transmitter switch. The green LED will flash once and then turn off to show that that button was learned. 3. Repeat steps 1 and 2 to learn more buttons into channel 1.