Owner's Manual

ManualsBrandsSunwell Technology ManualsElectronicsFireplace Remote Control

Table Of Contents

Page 1 of 6

RCB07

Standard Thermostatic On/Off Remote Control

INSTALLATION AND OPERATING INSTRUCTIONS

This wireless thermostatic on/off/ remote control system provides a safe, reliable, and user-friendly remote control

for millivolt valve gas appliances. The system can be thermostatically or manually turned on and off with the

transmitter. Always check the appliance home owner’s manual for additional information, or warnings regarding

accessory installation before connecting this remote control system.

Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately contact the

dealer from whom you purchased the kit. Do not attempt to install any part of the kit unless all parts are in good

condition. Please keep these instructions for future reference.

CONTENTS OF KIT

Description Quantity

Transmitter 1

Battery Alkaline AAA (for Transmitter) 2

Battery Alkaline AA (for receiver) 4

Receiver Box 1

Slide Button-Black (On/RS/Off) 1

Slide Button-White (On/RS/Off) 1

Wall Cover Plate-Black 1

Wall Cover Plate-White 1

Battery Door- Black 1

Battery Door-White 1

Plug-In Wiring Assembly – 22” Inches 1

Installation Instructions 1

#6 3/4 Screws (for Wall Cover Plate) 2

#8 Screws (for fireplace system control covers) 2

Heat shield for receiver 1

NOTE:Due to the sensitive temperature monitoring components in the transmitter,it is necessary to allow the

transmitter to stabilize to room temperature before accurate room temperature are displayed, If the transmitter is

activated from a severe cold condition allow 15 minutes for accurate temperature reading to appear on the LCD.

WARNING

Important Safety Information

 Read this manual thoroughly prior to installing, programming or operating any remote control.

 This remote control system is designed for use with a millivolt or 24V gas valve system. Do not use this

remote control system on applications with voltages above 24 Volts AC/DC and 1 amp current.

 This remote control system requires two (2) “AAA” and four (4) “AA” alkaline batteries to power the

transmitter and receiver.

 Wiring must conform to appliance requirement and building codes/ordinances as required by local and

national code authorities having jurisdiction.

 Do not short (or jumper) across the gas valve terminals to test the remote control installation. This could

damage the unit and void the warranty.

 This remote control system should only be used as described in this manual. Any other use is prohibited

and will void the warranty.

Summary of content (7 pages)

PAGE 1
RCB07 Standard Thermostatic On/Off Remote Control INSTALLATION AND OPERATING INSTRUCTIONS This wireless thermostatic on/off/ remote control system provides a safe, reliable, and user-friendly remote control for millivolt valve gas appliances. The system can be thermostatically or manually turned on and off with the transmitter. Always check the appliance home owner’s manual for additional information, or warnings regarding accessory installation before connecting this remote control system.
PAGE 2
FEATURES/SPECIFICATIONS WARNING Easy Access Thermostatic Control Battery Powered Transmitter and Receiver Low battery Indication Child Proof Lock-out 16 Security Codes 6 hour Shut Down (Optional) Quick Disconnect Wiring Assembly Reset Button Turn appliance OFF and allow to cool before installing or servicing. DO NOT connect 110-120 VAC wiring to the millivolt gas control valve. The remote operator must be installed exactly as outlined in these instructions.
PAGE 3
Connecting the Receiver to your appliance: This system comes with an 22 inch wire assembly. Insert the white terminal to the back of the receiver. The terminal wire block can only be installed one way. Do not force the terminal plug onto the receiver. WARNING Connect the wiring terminal two (2) ¼” female spade terminals to the appliance. Refer to the appropriate Homeowner’s Manual for proper wiring connections to the appliance. Your appliance may have other options to connect wiring from receiver.
PAGE 4
Transmitter Receiver Dip Switch (Default) ON ON DIP DIP WARNI NG Reset Button: The reset button can be used to reset the transmitter if transmitter is not working properly. The reset button is located closed to the battery door cover. press the reset button and the transmitter will reset and initialize for few seconds before it can be used. Do not use two (2) or more remote control systems in the same area with the same dip switch settings, as they will communicate with each other.
PAGE 5
Initial start up: 1. After initial power up or when RESET button is pressed, the transmitter is reset. The reset button is located close the battery door. 2. During system reset, all features of the LCD will be visible. After one second, the LCD will be initialized. A typical reset display is shown right. After reset the transmitter is operating. The room temperature is shown as right. Manual Mode: 1. Press the button once to turn on the appliance. button once again to turn off the appliance. 2.
PAGE 6
Transmitter Thermal Shutdown: 1. If transmitter measures a room temperature exceeding 99 degrees Fahrenheit, the LCD will display "HI" and the transmitter will turn off the appliance. 2. Transmitter will not function until the room temperature has dropped below 99 degree Fahrenheit. 3. If transmitter measures a room temperature less than 40 degrees Fahrenheit, the LCD will display “LO” and NO SIGNAL will be send to turn on the appliance. Receiver: Slide Switch: 1.
PAGE 7
FCC COMPLIANCE STATEMENT: This device complies with part 15 of theFCC Rules. Operation is subject to the followingtwo conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operatethe equipment.