ST3330 User Manual Suntech International Ltd.
ST3330 User Manual 1. Introduction This document describes features, protocols and detail operation of ST3330. If there is another operation description document for special buyer to customize or model and the contents of the document is different with this, customizing document should be applied for special buyer. 2. Overview Device consists of WCDMA, GPS and event parts. The main purpose of device reports getting GPS position and other informs of asset to server periodically.
ST3330 User Manual 2-3. Setting Parameter Parameters of device can be changed by WCDMA or SMS, and some control can be realized also in the same way. Detail protocols are described in Chapter 4. 2-4. Features Key features are described here; - Power Down Device can process two steps of power-down, Sleep and Deep Sleep, for reducing power consumption when the asset is parked. - LED Indicator LED indicates WCDMA and GPS states. It’s helpful to check error cause.
ST3330 User Manual - Main Power Checking The device can recognize the main power and inform to server when main power line is disconnected or main power drops below preset value. It’s applicable only for battery model. - Battery Error Alert Device can alert about battery error related on charging. It’s applicable only for battery model. 3. Protocol Construction All command and reports are string and follows below format. Every filed is distinguished by semi colon.
ST3330 User Manual Field 1 ~ n String Contents 4. Commands When the device is received a command, it responds with response string and changes some parameters or acts related operation. 4-1. Network Parameters Setting HDR DEV_ID B_SEVER_IP ● Definition VER AUTH B_SEVER_IP Definitions HDR “ST3330NTW” VER AUTH USER_ID SMS_NO USER_PWD SEVER_IP SEVER_PORT PIN_NO : Set network parameters and PIN number. Field DEV_ID APN 6 char.
ST3330 User Manual [command] ST3330NTW;850000;02;0;internet;;;111.111.111.111;8600;;;; [response] ST3330NTW;Res;850000;010;0;internet;;; 111.111.111.111;8600;;;; ST3330NTW;Res;850000;010;A1;tim.br;tim;tim; 111.111.111.111;8600;;;; ** If network does not require User ID and Password, these fields should be empty. Automatic WCDMA Set It the device is set to ‘Automatic WCDMA Set’, the device set WCDMA parameters automatically depending on inserted SIM.
ST3330 User Manual T3 String Sec Interval for sending status report in emergency mode Range : 0 ~ 9999 If 0, emergency report will be sent only one time when emergency state occurs. A1 String Number of attempts for emergency report until the device gets acknowledge from server If 0, no emergency report will be sent. SND_DIST String Meter Distance interval for sending status report. Range : 0 ~ 60000 (60km) If 0, status report related on moving distance is disabled.
ST3330 User Manual IN1_TYPE IN2_TYPE IN3_TYPE IN1_CHAT OUT1_TYPE OUT2_TYPE OUT1_ACTIVE OUT2_ACTIVE PULSE1_NO PULSE1_ON PULSE1_OFF IN4_TYPE IN5_TYPE IN4_CHAT ● Definition Definitions HDR “ST3330EVT” VER IN3_CHAT PULSE2_NO PULSE2_ON PULSE2_OFF IN5_CHAT BAUD : Set parameter related event. Field DEV_ID IN2_CHAT Unit Remark Command type 6 char.
ST3330 User Manual OUT1_TYPE ‘0’ ~ ‘5’ 0 = GPIO 1 = immobilizer 2 = Immobilizer & Auto active Auto active means immobilizer is activated automatically when the asset starts parking. 3 = Pulse 4 = LED Out for indicating call status. Refer 7-2-3. 5 = Buzzer OUT1_ACTIVE ‘0’ or ‘1’ 0 = Open when out1 is active 1 = GND when out1 is active PULSE1_NO String Pulse number when out1 type set to pulse. Range : 0 ~ 9999 If pulse no is 9999, pulsing runs permanently.
ST3330 User Manual [command] ST3330EVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0 [response] ST3330EVT;Res;850000;010;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0 ** If IGNITION is set to ‘0’, device doesn’t check driving or parking state of the asset. It reports status string with idle mode always, and cannot support parking lock and the service that enters sleep or deep sleep automatically when the asset is parked.
ST3330 User Manual IN1_TYPE ‘0’ ~ ‘5’ 0 = Falling Edge 1 = Rising Edge 2 = Both Edge (Falling & Rising) 3 = Panic Button 4 = Call1 Button 5 = Call 2 Button 6 = Reserved 7 = Anti-Theft Button 13 = Disable Immobilizer if it’s activated by jammer detector. Default = ‘3’. Only the device that included voice option (audio circuit) can be set to ‘Call1 Button’ or ‘Call2 Button’. IN1_CHAT String 100ms Input1 chattering time. Range : 0 ~ 9999 Default = 3 sec. If 0, input1 is not checked.
ST3330 User Manual CALL_MO1 ● Definition CALL_MO2 : Set parameters related SMS or Call. Field Definitions HDR “ST3330WCD Unit Remark Command type MA” DEV_ID VER SMS_LOCK 6 char. Device ID “02” Protocol Version ‘0’ or ‘1’ Lock of Receiving Commands by SMS Disable (0) / Enable (1) If enabled, only commands that receives from SMS_MT1 ~ MT3 number can be accepted. SMS_MT1 String Up to 20 char. Phone number for SMS commands SMS_MT2 String Up to 20 char.
ST3330 User Manual HDR DEV_ID VER PARKING_LOCK SPEED_LIMIT PWR_DN CON_TYPE ZIP GROUP_SEND MP_CHK ANT_CHK BAT_CHK M_SENSOR CALL GEO_FENCE DATA_LOG ANTITHFT_CNT1 ANTITHFT_CNT2 JAM_DET JAM_CHK_DIST JAM_CHK_TM ● Definition : Set parameters related report. Field Definitions HDR “ST3330SVC” DEV_ID VER PARKING_LOCK Unit Remark Command type 6 char.
ST3330 User Manual ANT_CHK ‘0’ or ‘1’ GPS Antenna Connection Error Check Disable (0) / Enable (1) BAT_CHK ‘0’ or ‘1’ Backup Battery Error Check Disable (0) / Enable (1) M_SENSOR CALL ‘0’ ~’4’ ‘0’ or ‘1’ Motion Sensor Motion Collision Shock 0 Disable Disable Disable 1 Enable Disable Disable 2 Disable Disable Enable 3 Enable Disable Enable 4 Disable Enable Disable 5 Enable Enable Disable 6 Disable Enable Enable 7 Enable Enable Enable Support Call with headset Disab
ST3330 User Manual on report parameters. It may be used for saving WCDMA fee. Current version cannot support this option. Group Send The device stores data if the asset is in no WCDMA area. And, the asset moves to WCDMA available area, device starts sending stored data. If group send option is enabled, the device makes 5 reports to one bundle and send these 5 reports at one time. Group send is useful to speed up sending. M_Sensor 1.
ST3330 User Manual VER SVR_TYPE “02” ‘T’ / ‘U’ Protocol Version Server Protocol Type T : TCP U : UDP B_SVR_TYPE ‘T’ / ‘U’ Backup Server Protocol Type T : TCP U : UDP UDP_ACK ‘0’ ~ ‘3’ ACK from Server when UPD is used. 0 : No use 1 : ACK when the server receives reports except alive. 2 : ACK when the server receives reports except STT and alive report. 3 : ACK when the server receives emergency report. Command response doesn’t need ACK.
ST3330 User Manual reached to server and sends the data again. Examples of ACK report are as below. String Format : “ST3330ACK;850000” Zip Format : 0x15 0x85 0x00 0x00 It is recommended ACK_TYPE is set to ‘1’ to confirm all data can be transmitted safely. Report Type UDP_ACK=0 UDP_ACK=1 UDP_ACK=2 UDP_ACK=3 Alive X X X X STT X O X X Event, Alert, Etc. X O O X Emergency X O O O 4-7.
ST3330 User Manual IGNDET_L String In case of virtual ignition, the asset can recognize parking state when asset power is less than IGNDET_L. Default = ‘0’ [command] ST3330MBV;850000;02;10.5;22;19;8.00;18.00;0;0 [response] ST3330MBV;Res;850000;122;10.5;22;19;8.00;18.00;0;0 IGNDET_H and IGNDET_L are ‘0’, device check parking and driving automatically. 4-8.
ST3330 User Manual VI_ON_DELAY String Sec. Delay time for Motion Virtual Ignition On Range : 3~999 Default : 10 VI_ON_PERCENT String % Percent for Motion Virtual Ignition On. Range : 30~100 Default: 70 VI_OFF_THRES String 1/255G Threshold value for Motion Virtual Ignition Off Range : 3~50 Default : 5 VI_OFF_DELAY String Sec. Delay time for Motion Virtual Ignition Off Range : 3~999 Default : 10 VI_OFF_PERCENT String % Percent for Motion virtual Ignition Off.
ST3330 User Manual 4-11-1. Status Request ● Definition : Location poll, request of the status report. Field Definitions CMD_ID “StatusReq” Unit Remark Status request If received, the device sends status string instantly. [command] ST3330CMD;850000;02;StatusReq [response] ST3330STT;850000;010;20090724;07:12:16;00129;+37.479995;+126.885815;000.029;000.00; 7;1;0;15.33;100000;2;0002 4-11-2. Reset ● Definition Field CMD_ID : Reset all of parameters.
ST3330 User Manual [command] ST3330CMD;850000;02;Preset [response] ST3330CMD;Res;850000;010;Preset; NTW;0;internet;;;111.111.111.111;8600;;;;1234; RPT;60;180;120;60;3;0;0;;;; EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0; WCDMA;0;;;;;0;;;;;;;; SVC;1;120;0;0;0;0;1;1;1;0;0;0;0 DEV;0;0;0;0 [response] event 4 line model NTW;0;internet;;;111.111.111.
ST3330 User Manual ADP;U;T;2;9000;0;0;0;0;0;0; DEV;0;0;0;0;0;0;0;0 ** This command can be applied from software version 22. ** DEV filed informs current status of device as below. OUT1 OUT2 PWR_DN 0 = Disable 0 = Disable 0 = Normal 1 = Enable 1 = Enable 1 = Sleep 2 = Deep sleep TRACKING Anti-Theft 0 = Stop Tracking 0 = Disable 1 = Start Tracking 1 = Enable BAT_CON 0 = Backup battery is disconnected. 1 = Backup battery is connected. Reserved Reserved 4-11-4.
ST3330 User Manual [command] ST3330CMD;850000;02;Enable1 [response] ST3330CMD;Res;850000;010;Enable1 [response] ST3330CMD;Res;850000;010;Enable1NoUse (in case that IN type is set to ‘No Use’). ** Output1 line goes to active status. ** If OUT1 set with immobilizer, output1 line goes to active status gradually with pulse in driving mode. ** If OUT1 set with pulse type, output1 line generates pulse and returns inactive state after pulsing out automatically. 4-11-6.
ST3330 User Manual ● Definition : Request the ICCID. Field Definitions CMD_ID “ReqICCID” Unit Remark Request ICCID (sequence number that is displayed on SIM) If received, device sends ICCID of using SIM. [command] ST3330CMD;850000;02;ReqICCID [response] ST3330CMD;Res;850000;010;ReqICCID;89550230000084256668 4-11-11. ReqVer ● Definition : Request software version.
ST3330 User Manual ● Definition : Initialize the travel distance. Field Definitions CMD_ID Unit “InitDist” Remark Set traveled distance to 0. [command] ST3330CMD;850000;02;InitDist [response] ST3330CMD;Res;850000;010;InitDist 4-11-14. Initialize Message Number ● Definition : Initialize the message sequence number. Field Definitions CMD_ID “InitMsgNo” Unit Remark Set message number to 0.
ST3330 User Manual [command] ST3330CMD;850000;02;ReqSIMIP [response] ST3330CMD;Res;850000;010;ReqSIMIP;172.16.18.
ST3330 User Manual 3. Installation 3.1 Insert SIM card. 3.2 Backup battery - The backup battery should be used when main power is cut off 3.3 Install - The Device is fixed to the asset. 3.
ST3330 User Manual Red: VCC (12V) only charging Black: Ground Caution: Please charge using the charger specified by the Suntech. Caution: Use the company designated by Suntech for charging and device setting. 3.5 Check GPS/WCDMA operation and battery charger operation with LEDs. It takes 3~10 minutes for GPS connected. Caution: Direction of ST3330 is very important when installed in the asset.
ST3330 User Manual 4. Trouble Shooting (LED Indicator) 4.1 Blue LED: Indicates WCDMA status. WCDMA Blink Count Normal 1 Server Com. Error 2 Remarks 1. Server or network parameter is wrong. 2. Server is closed. 3. Temporary network barrier WCDMA Com. 3 Error 1. Network parameter is wrong. 2. SIM is blocked about WCDMA using. 3. Temporary network barrier 4. Weak WCDMA signal 5. WCDMA antenna connection is not firm. No Network 4 1.
ST3330 User Manual 4.2 RED LED: Indicates GPS status. GPS Blink Count Normal 1 No Fix 2 Remarks 1. If power on, GPS chipset is trying to find position during some minutes. 2. GPS antenna lays on weak or no GPS signal position 3. GPS antenna connection is not firm. GPS Chipset Error GPS Antenna Error 4 1. GPS antenna is disconnected. 2. GPS antenna or socket of GPS antenna is broken. 3. Unit is broken.
