ST3310 User Manual Suntech International Ltd.
ST3310 User Manual 1. Introduction This document describes features, protocols and detail operation of ST3310. If there is another operation description document for special buyer to customize or model and the contents of the document is different with this, customizing document should be applied for special buyer. 2. Overview Device consists of WCDMA, GPS and event parts. The main purpose of device reports getting GPS position and other informs of vehicle to server periodically.
ST3310 User Manual 2-3. Setting Parameter Parameters of device can be changed by WCDMA or SMS, and some control can be realized also in the same way. Detail protocols are described in Chapter 4. 2-4. Features Key features are described here; - Power Down Device can process two steps of power-down, Sleep and Deep Sleep, for reducing power consumption when the vehicle is parked. - LED Indicator LED indicates WCDMA and GPS states. It’s helpful to check error cause.
ST3310 User Manual - Main Power Checking The device can recognize the main power and inform to server when main power line is disconnected or main power drops below preset value. It’s applicable only for battery model. - Battery Error Alert Device can alert about battery error related on charging. It’s applicable only for battery model. 3. Protocol Construction All command and reports are string and follows below format. Every filed is distinguished by semi colon.
ST3310 User Manual Field 1 ~ n String Contents 4. Commands When the device is received a command, it responds with response string and changes some parameters or acts related operation. 4-1. Network Parameters Setting HDR DEV_ID B_SEVER_IP ● Definition VER AUTH B_SEVER_IP Definitions HDR “ST3310NTW” VER AUTH USER_ID SMS_NO USER_PWD SEVER_IP SEVER_PORT PIN_NO : Set network parameters and PIN number. Field DEV_ID APN 6 char.
ST3310 User Manual [command] ST3310NTW;850000;02;0;internet;;;111.111.111.111;8600;;;; [response] ST3310NTW;Res;850000;010;0;internet;;; 111.111.111.111;8600;;;; ST3310NTW;Res;850000;010;A1;tim.br;tim;tim; 111.111.111.111;8600;;;; ** If network does not require User ID and Password, these fields should be empty. Automatic WCDMA Set It the device is set to ‘Automatic WCDMA Set’, the device set WCDMA parameters automatically depending on inserted SIM.
ST3310 User Manual T3 String Sec Interval for sending status report in emergency mode Range : 0 ~ 9999 If 0, emergency report will be sent only one time when emergency state occurs. A1 String Number of attempts for emergency report until the device gets acknowledge from server If 0, no emergency report will be sent. SND_DIST String Meter Distance interval for sending status report. Range : 0 ~ 60000 (60km) If 0, status report related on moving distance is disabled.
ST3310 User Manual IN1_TYPE IN2_TYPE IN3_TYPE IN1_CHAT OUT1_TYPE OUT2_TYPE OUT1_ACTIVE OUT2_ACTIVE PULSE1_NO PULSE1_ON PULSE1_OFF IN4_TYPE IN5_TYPE IN4_CHAT ● Definition Definitions HDR “ST3310EVT” VER IN3_CHAT PULSE2_NO PULSE2_ON PULSE2_OFF IN5_CHAT BAUD : Set parameter related event. Field DEV_ID IN2_CHAT Unit Remark Command type 6 char.
ST3310 User Manual OUT1_TYPE ‘0’ ~ ‘5’ 0 = GPIO 1 = immobilizer 2 = Immobilizer & Auto active Auto active means immobilizer is activated automatically when the vehicle starts parking. 3 = Pulse 4 = LED Out for indicating call status. Refer 7-2-3. 5 = Buzzer OUT1_ACTIVE ‘0’ or ‘1’ 0 = Open when out1 is active 1 = GND when out1 is active PULSE1_NO String Pulse number when out1 type set to pulse. Range : 0 ~ 9999 If pulse no is 9999, pulsing runs permanently.
ST3310 User Manual [command] ST3310EVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0 [response] ST3310EVT;Res;850000;010;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0 ** If IGNITION is set to ‘0’, device doesn’t check driving or parking state of the vehicle. It reports status string with idle mode always, and cannot support parking lock and the service that enters sleep or deep sleep automatically when the vehicle is parked.
ST3310 User Manual IN1_TYPE ‘0’ ~ ‘5’ 0 = Falling Edge 1 = Rising Edge 2 = Both Edge (Falling & Rising) 3 = Panic Button 4 = Call1 Button 5 = Call 2 Button 6 = Reserved 7 = Anti-Theft Button 13 = Disable Immobilizer if it’s activated by jammer detector. Default = ‘3’. Only the device that included voice option (audio circuit) can be set to ‘Call1 Button’ or ‘Call2 Button’. IN1_CHAT String 100ms Input1 chattering time. Range : 0 ~ 9999 Default = 3 sec. If 0, input1 is not checked.
ST3310 User Manual CALL_MO1 ● Definition CALL_MO2 : Set parameters related SMS or Call. Field Definitions HDR “ST3310WCD Unit Remark Command type MA” DEV_ID VER SMS_LOCK 6 char. Device ID “02” Protocol Version ‘0’ or ‘1’ Lock of Receiving Commands by SMS Disable (0) / Enable (1) If enabled, only commands that receives from SMS_MT1 ~ MT3 number can be accepted. SMS_MT1 String Up to 20 char. Phone number for SMS commands SMS_MT2 String Up to 20 char.
ST3310 User Manual HDR DEV_ID VER PARKING_LOCK SPEED_LIMIT PWR_DN CON_TYPE ZIP GROUP_SEND MP_CHK ANT_CHK BAT_CHK M_SENSOR CALL GEO_FENCE DATA_LOG ANTITHFT_CNT1 ANTITHFT_CNT2 JAM_DET JAM_CHK_DIST JAM_CHK_TM ● Definition : Set parameters related report. Field Definitions HDR “ST3310SVC” DEV_ID VER PARKING_LOCK Unit Remark Command type 6 char.
ST3310 User Manual ANT_CHK ‘0’ or ‘1’ GPS Antenna Connection Error Check Disable (0) / Enable (1) BAT_CHK ‘0’ or ‘1’ Backup Battery Error Check Disable (0) / Enable (1) M_SENSOR CALL ‘0’ ~’4’ ‘0’ or ‘1’ Motion Sensor Motion Collision Shock 0 Disable Disable Disable 1 Enable Disable Disable 2 Disable Disable Enable 3 Enable Disable Enable 4 Disable Enable Disable 5 Enable Enable Disable 6 Disable Enable Enable 7 Enable Enable Enable Support Call with headset Disab
ST3310 User Manual on report parameters. It may be used for saving WCDMA fee. Current version cannot support this option. Group Send The device stores data if the vehicle is in no WCDMA area. And, the vehicle moves to WCDMA available area, device starts sending stored data. If group send option is enabled, the device makes 5 reports to one bundle and send these 5 reports at one time. Group send is useful to speed up sending. M_Sensor 1.
ST3310 User Manual VER SVR_TYPE “02” ‘T’ / ‘U’ Protocol Version Server Protocol Type T : TCP U : UDP B_SVR_TYPE ‘T’ / ‘U’ Backup Server Protocol Type T : TCP U : UDP UDP_ACK ‘0’ ~ ‘3’ ACK from Server when UPD is used. 0 : No use 1 : ACK when the server receives reports except alive. 2 : ACK when the server receives reports except STT and alive report. 3 : ACK when the server receives emergency report. Command response doesn’t need ACK.
ST3310 User Manual reached to server and sends the data again. Examples of ACK report are as below. String Format : “ST3310ACK;850000” Zip Format : 0x15 0x85 0x00 0x00 It is recommended ACK_TYPE is set to ‘1’ to confirm all data can be transmitted safely. Report Type UDP_ACK=0 UDP_ACK=1 UDP_ACK=2 UDP_ACK=3 Alive X X X X STT X O X X Event, Alert, Etc. X O O X Emergency X O O O 4-7.
ST3310 User Manual In case of virtual ignition, the vehicle can recognize IGNDET_H driving String state when vehicle power is more than IGNDET_H. Default = ‘0’ IGNDET_L String In case of virtual ignition, the vehicle can recognize parking state when vehicle power is less than IGNDET_L. Default = ‘0’ [command] ST3310MBV;850000;02;10.5;22;19;8.00;18.00;0;0 [response] ST3310MBV;Res;850000;122;10.5;22;19;8.00;18.
ST3310 User Manual Recommend : 0.7 VI_ON_THRES String 1/255G Threshold value for Motion Virtual Ignition On Range : 3~50 Default : 5 VI_ON_DELAY String Sec. Delay time for Motion Virtual Ignition On Range : 3~999 Default : 10 VI_ON_PERCENT String % Percent for Motion Virtual Ignition On. Range : 30~100 Default: 70 VI_OFF_THRES String 1/255G Threshold value for Motion Virtual Ignition Off Range : 3~50 Default : 5 VI_OFF_DELAY String Sec.
ST3310 User Manual VER ‘01’ CMD_ID Protocol Version String Control command content Caution : If it’s not correct the Unit ID, ignored. 4-11-1. Status Request ● Definition : Location poll, request of the status report. Field Definitions CMD_ID “StatusReq” Unit Remark Status request If received, the device sends status string instantly. [command] ST3310CMD;850000;02;StatusReq [response] ST3310STT;850000;010;20090724;07:12:16;00129;+37.479995;+126.885815;000.029;000.
ST3310 User Manual Field Definitions CMD_ID Unit Remark “Preset” Report parameter setting values and current device status. Response includes network, report, event, WCDMA and service parameters. It includes status of device, also. [command] ST3310CMD;850000;02;Preset [response] ST3310CMD;Res;850000;010;Preset; NTW;0;internet;;;111.111.111.
ST3310 User Manual RPT;60;180;120;60;3;0;0;;;; EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0; WCDMA;0;;;;;0;;;;;;;; SVC;1;120;0;0;0;0;1;1;1;0;0;0;0; ADP;U;T;2;9000;0;0;0;0;0;0; DEV;0;0;0;0;0;0;0;0 ** This command can be applied from software version 22. ** DEV filed informs current status of device as below.
ST3310 User Manual ● Definition : Active Output1. Field Definitions CMD_ID Unit “Enable1” Remark Enable Output1 [command] ST3310CMD;850000;02;Enable1 [response] ST3310CMD;Res;850000;010;Enable1 [response] ST3310CMD;Res;850000;010;Enable1NoUse (in case that IN type is set to ‘No Use’). ** Output1 line goes to active status. ** If OUT1 set with immobilizer, output1 line goes to active status gradually with pulse in driving mode.
ST3310 User Manual [response] ST3310CMD;Res;850000;010;ReqIMSI;724031111553779 4-11-10. Request ICCID ● Definition : Request the ICCID. Field Definitions CMD_ID “ReqICCID” Unit Remark Request ICCID (sequence number that is displayed on SIM) If received, device sends ICCID of using SIM. [command] ST3310CMD;850000;02;ReqICCID [response] ST3310CMD;Res;850000;010;ReqICCID;89550230000084256668 4-11-11. ReqVer ● Definition : Request software version.
ST3310 User Manual [response] ST3310CMD;Res;850000;010;EraseAll 4-11-13. Initialize Traveled Distance ● Definition : Initialize the travel distance. Field Definitions CMD_ID Unit “InitDist” Remark Set traveled distance to 0. [command] ST3310CMD;850000;02;InitDist [response] ST3310CMD;Res;850000;010;InitDist 4-11-14. Initialize Message Number ● Definition : Initialize the message sequence number. Field Definitions CMD_ID “InitMsgNo” Unit Remark Set message number to 0.
ST3310 User Manual 4-11-24. Request SIM IP Address ● Definition Field CMD_ID : Request of the local IP address in SIM card. Definitions Unit “ReqSIMIP” Remark SIM card IP request [command] ST3310CMD;850000;02;ReqSIMIP [response] ST3310CMD;Res;850000;010;ReqSIMIP;172.16.18.
ST3310 User Manual 3. Installation 3.1 Insert SIM card. 3.2 Backup battery - The backup battery should be used when main power is cut off 3.3 Install - The Device is fixed to the vehicle. 3.
ST3310 User Manual Event Cable Color pin Description Red: VCC (12V) Black: Ground Blue: Ignition (12V) Connect to Ignition signal line of vehicle. White: Input1. Panic Button When Input1 goes to GND, then ST3310 change Emergency mode. It reports emergency string by mode 1 in Emergency mode such that SA200EMG;850000;20081017;07:41:56;00100;+37.478519;+126.886819;000.012;000.00;9;1;0;15.30; 110000;1 Yellow: Input2.
ST3310 User Manual generates pulse when it is activated. Immobilizer activation behaves progressive blocking when vehicle is driving. The progressive blocking diagram is as below. The active time of the immobilizer increases 90ms each 4s. After 3minutes, immobilizer is activated continuously. When one of output is dedicated to PULSE, it operates as below. Time for activation and deactivation is configurable by PULSE_ON and PULSE_OFF in Service Parameter.
ST3310 User Manual 4. Trouble Shooting (LED Indicator) 4.1 Blue LED: Indicates WCDMA status. WCDMA Blink Count Normal 1 Server Com. Error 2 Remarks 1. Server or network parameter is wrong. 2. Server is closed. 3. Temporary network barrier WCDMA Com. 3 Error 1. Network parameter is wrong. 2. SIM is blocked about WCDMA using. 3. Temporary network barrier 4. Weak WCDMA signal 5. WCDMA antenna connection is not firm. No Network 4 1.
ST3310 User Manual 4.2 RED LED: Indicates GPS status. GPS Blink Count Normal 1 No Fix 2 Remarks 1. If power on, GPS chipset is trying to find position during some minutes. 2. GPS antenna lays on weak or no GPS signal position 3. GPS antenna connection is not firm. GPS Chipset Error GPS Antenna Error 4 1. GPS antenna is disconnected. 2. GPS antenna or socket of GPS antenna is broken. 3. Unit is broken.
