ST210 User Guide Suntech International Ltd.
Table of Contents 1. Introduction ........................................................................................................................................... 1 2. Parameter Setting via SMS................................................................................................................... 1 For reporting GPS position, the device should be set with adjustable parameters before installation. .........................................................................................
Doc. Type Author Page User Guide JH KIM 1/11 Model Rev. Date ST210 1.15 10-09-02 1. Introduction This document describes Configuration, Parameter Setting and Installation Procedure of ST210 (including backup battery). 2. Parameter Setting via SMS For reporting GPS position, the device should be set with adjustable parameters before installation. When SMS for setting is sent, the device replies response to predefined server though GPRS and sets corresponding parameters.
Doc. Type Author Page User Guide JH KIM 2/11 Model Rev. Date ST210 1.15 10-09-02 2.2 Report Parameter Setting Field HDR DEV_ID VER T1 Definitions “SA200RPT” 6 char. “02” String Unit T2 String Sec T3 String Sec A1 String SND_DIST String Sec Meter Remark Command type Device ID Protocol Version Interval for sending status report in parking mode Range : 0 ~ 86400 If 0, report in parking will be sent only one time when vehicle starts parking.
Doc. Type Author Page User Guide JH KIM 3/11 Model Rev. Date ST210 1.15 10-09-02 2.4 Deactivate Output1 Field Definitions Unit Remark CMD_ID “Disable1” Disable Output1 [command] SA200CMD;850000;02;Disable1 [response] SA200CMD;Res;850000;010;Disable1 ** Output1 line goes to inactive status. 2.
Doc. Type Author Page User Guide JH KIM 4/11 Model Rev. Date ST210 1.15 10-09-02 3. Installation 3.1 Bottom case. 3.2 Remove battery cover. 3.3 Insert SIM card.
Doc. Type Author Page User Guide JH KIM 5/11 Model Rev. Date ST210 1.15 10-09-02 3.4 Install back-up battery.
Doc. Type Author Page User Guide JH KIM 6/11 Model Rev. Date ST210 1.15 10-09-02 3.5 Lock battery cover. 3.6 Connect 10-pin event cables. Red: VCC (8 - 30V) Black: Ground Blue: Ignition (8V - 32V) Connect to Ignition signal line of vehicle. White: Input1. Panic Button When Input1 goes GND, then ST210 change Emergency mode. It reports emergency string by mode 1 in Emergency mode such that SA200EMG;850000;20081017;07:41:56;00100;+37.478519;+126.886819;000.012;000.00;9;1;0;15.
Doc. Type Author Page User Guide JH KIM 7/11 Model Rev. Date ST210 1.15 10-09-02 In this case, you have to set IGNITION in Service Parameter to ‘0’. Refer to OperationDescription document for more detailed information about parameters. 3.7 Connect GPS antenna. ST210E needs to connect GPS antenna. 3.8 Check GPS/GPRS operation with LEDs. It takes 3~10 minutes for GPS connected. Caution: Direction of ST210I is very important when installed in the vehicle.
Doc. Type Author Page User Guide JH KIM 8/11 Model Rev. Date ST210 1.15 10-09-02 4. Trouble Shooting (LED Indicator) 4.1 Red LED: Indicates GPRS status. GPRS Normal Blink Count 1 Server Com. Error 2 Remarks 1. Server or network parameter is wrong. 2. Server is closed. 3. Temporary network barrier GPRS Com. Error 3 1. Network parameter is wrong. 2. SIM is blocked about GPRS using. 3. Temporary network barrier 4. Weak GPRS signal 5.
Doc. Type Author Page User Guide JH KIM 9/11 Model Rev. Date ST210 1.15 10-09-02 4.2 Green LED: Indicates GPS status. GPS Normal Blink Count 1 No Fix 2 Remarks 1. If power on, GPS chipset is trying to find position during some minutes. 2. GPS antenna lays on weak or no GPS signal position 3. GPS antenna connection is not firm. GPS Chipset Error GPS Antenna Error 4 1. GPS antenna is disconnected. 2. GPS antenna or socket of GPS antenna is broken. 3.