Quick Start Guide

PANTONE Orange 021C
T8A10
QUICK START GUIDE
前置摄像头(选配)
指示灯
用于充电，信息，扫描等灯光提示。
自定义键
可设置快捷功能。
扫码键
短按启动扫码功能。
电源键
短按：点亮屏幕，锁定屏幕。
长按：关机状态下，长按2-3秒开机；
使用状态下，长按2-3秒，可选择关机或重启；
死机状态下，长按11秒，自动重启。
喇叭出声孔
注意:请保持出声孔清洁。
扫码头
用于条码数据采集。
注意:激光辐射，请勿直视!
后置摄像头
支持拍照及1D/2D快速扫码。
背部拓展接口
配置不同，数量不同
SIM&PSAM卡槽
SIM和PSAM功能二选一，默认是SIM卡功能，
PSAM功能仅特定的机型支持。
注意：插卡时按照标贴指示装入。
取卡时先扣住卡槽金属扣手将卡拖出，然后将金属
扣手推进去，再将卡取出。
Nano SIM&Micro SD卡槽
用于插入Nano SIM卡以及Micro SD卡。
注意：插入或取出Nano SIM卡时，请务必让机器
处于关机状态， 若开机状态下插拔可能造成机器
故障。
电池盖开关
左右滑动实现电池盖开关功能。
注意： 电池盖须安装在设备上，否则将影响正常
使用。
1
NFC读卡器
用以感应会员卡等NFC卡。
(选配)
13
2
3
4
5
6
7
8
10
9
11
12
快速入门指南
4
4
6
3
2
4
5
8
9
10
11
12
13
7
1
SIM/PSAM
Nano SIM
Micro SD
· 应用市场 · 推送服务 · 用户反馈 · 数据服务 · 启动器
· 硬件管家· 音量键功能自定义 · BaseService · 定制
服务(壁纸、开机动画) · 开发者指南(调试小助手)
· 使用指南 · 开机指导 · 远程协助 · OTA
系统预置软件列表
本产品有毒有害物质名称及含量标识表
部件名称
有毒有害物质或元素
电路板组件
结构件
多溴二苯醚
(PBDE)
包装件
汞
(Hg)
铅
（Pb）
镉
(Cd)
六价铬
(Cr(VI)
多溴联苯
(PBB)
对达到或超出环保使用年限的产品，应依据《电子信
息产品控制管理办法》规定进行回收再利用，不应随
意丢弃。
产品保修卡
产品名称：
产品型号：
产品编号：
购买日期：
保修期限：自购买之日起，我公司提供 天保修服务。
以下情况恕不提供免费保修：
· 未经允许擅自拆卸修理的产品。
· 产品条码、易碎贴破损及保修卡涂改、残缺的。
· 未按照说明书的要求操作设备所引起的故障。
· 因进水或跌落而造成的故障、划伤或破损的人为损坏。
· 因不可抗拒因素造成的故障或损坏。
· 保修期限外。
联系方式：
· 公司地址：
· 联系电话：
: 表示该有毒有害物质在该部件所有均质材料中的
含量均在SJ/T11363-2006规定的限量要求以下。
: 表示该有毒有害物质至少在该部件的某一均质材
料中的含量超出SJ/T11363-2006规定的限量要求；
但是上表中打“×”的部件，其含量超出是因为目
前业界还没有成熟的可替代的技术。
注意事项
产品合格证
检验合格
产品合格证
制造商：上海商米科技集团股份有限公司
地 址：上海市杨浦区淞沪路388号创智天地7号楼505室
M05052179
安全警告
· 请将交流电插头插入与配件电源适配器上标识输入相对应的
交流电插座中；
· 此为A级产品。在生活环境中，该产品可能会造成无线电
干扰。在这种情况下，可能需要用户对于干扰采取切实可
行的措施。
· 关于电池的更换：
① 用错误型号电池更换会有爆炸危险！
② 更换后的旧电池应交维修人员处置，切勿把它投入火
中！
重要安全说明
· 避免在雷电期间安装或使用，否则有被雷电电击的危险；
· 当您发现有异常气味，过热或烟雾情形下，请立刻切断
电源；
建议
· 不要在极端冷、热环境中使用；
· 尽量在清洁无尘环境中使用，避免细小物品落入终端中；
· 在未获允许的情况下，不要在医疗设备附近使用。
声明
本公司不对以下行为负责
· 不在本指南说明的条件下使用和维护所造成的损坏；
· 对于因选件或耗材(非本公司提供之最初产品或认可产品)
造成的损坏或问题；(未经本公司同意，无权进行产品修
改或变动)
· 本产品的操作系统支持官方的系统更新，如果用户刷了
第三方的ROM系统或者采用破解方式修改了系统文件，
可能会导致系统不稳定，以及带来安全风险和安全威胁。
免责申明
由于产品的更新，此文档的某些细节可能与产品不符，请
以实物为准，此文档的解释权归本公司。保留不预先通知
的情况下，修改本说明书的权利。
mm
制 图：
发行日期
图纸名称
物料编码：M05052179
供应商料号供 应 商
版本
单位
A
B
C
D
E
F
1 2 3 4 5 6 7 8
87654321
F
E
D
C
B
A
L2Ks 移动数据终端-----说明书
变更原因
张盼
20210914
增加NFC功能
华勤
1.2
Front Camera (Optional)
Indicator Light
For indicating the charging status, messages
and scans.
Function Button
Use it to create a custom shortcut.
Scan Button
Short press the button to scan barcodes.
Power Button
Short press: turn the screen on/off.
Long press: when the device is off, press for 2-3
seconds to turn on the device.
When the device is on, press for 2-3 seconds to
power off or restart the device.
When the system crashes, press for 11 seconds
to restart the device.
Speaker Holes
Please keep the speaker holes clean.
Scanner
For barcode data collection.
Note: laser radiation. Do not stare into beam.
Rear Camera
For photo taking and 1D/2D barcode scanning.
Pogo Pin
The number depends on the specific
configuration.
SIM/PSAM Card Slot
It by default is a SIM card slot, but you can
NFC Reader (optional)
For reading NFC cards ,like loyalty cards.
choose a PSAM card feature which is available
in certain device versions.
Note: please follow the instruction label to
insert the card. To remove the card, hold and
pull the metal slot handle out, push the handle
back and then take the card out.
1
2
3
4
5
6
7
8
10
9
Quick Start Guide
Table for Names and Content Identification of
Toxic and Hazardous Substances in this Product
Part
Toxic or Hazardous Substances and Elements
Circuit Board
Component
Structural
Component
PBDE
Packaging
Component
Hg
Pb Cd Cr(VI) PBB
The products that have reached or exceeded
environmental protection service life should be
recycled and reused according to the
Regulations on Control and Management of
Electronic Information Products, and should not
be discarded randomly.
: indicates that the content of the toxic and
hazardous substance in all homogeneous
materials of the component is below the limit
specified in SJ/T 11363-2006.
: indicates that the content of the toxic and
hazardous substance in at least one
homogeneous material of the component
exceeds the limit stipulated in SJ/T 11363-2006.
However, as for the reason, because there is
no mature and replaceable technology in the
industry at present.
11
12
13
制作工艺说明
成品尺寸：62mm × 155mm
展开尺寸：310mm × 155mm
工艺：黑色印刷+2专色，5折页
材质：105g 雅粉纸
PANTONE 165C
封面
封底
Manufacturer:
Shanghai Sunmi Technology Co., Ltd.
Room 505, Building 7, KIC Plaza, 388 Songhu Rd.,
Yangpu District, Shanghai, China.
Nano SIM & Micro SD Card Slot
For Nano SIM card and Micro SD card.
Note: please shut down the device down before
inserting or taking the Nano SIM card out.
Otherwise, it may cause device malfunction.
Battery Cover Lock
Slide to open or close the cover.
Note: please keep the cover closed.
Otherwise, it may affect your use.
Notices
Safety Warning
· Connect the AC plug to the AC socket corr e
sponding
to the marked input of the power ada pter;
· This is a Class A product. This product may cause
radio interference in living environments. In that
case, the user may be required to take adequate
measures against interference.
· Battery replacement:
① Explosion danger may arise if replacing with
the wrong battery!
Significant Safety Instructions
②
The replaced battery shall be disposed of by
maintenance personnel, and please do not throw
it into fire!
· Do not install or use the device during light
ning
stor ms to avoid the poten tial risks of light ning shock;
· Please turn off the power immediately if you
notice abnormal odor, heat or smoke;
Suggestions
· Do not use the terminal in extremely cold or hot environments;
· Use the ter minal in a clean and dust-free
environment if possib le to prevent small items from
fall ing into the ter minal;
· Do not use the terminal near medical equipment
without permission.
Statements
The Company does not assume responsibilities for
the following actions:
· Damages caused by use and maintenance
without complying with the conditions specified in this guide;
· The Co mpany wil l not assume any respon
sibilities for
the damages or problems caused by optional items
or co nsum ab les (rather t han the initial products or
ap proved products of the Co mpany). The c ustomer
is not en titled to c hange or m odify the product
without our co nsent .
· The product’s operating system supports official
system updates, but if you change the operating
system into a third party ROM system or alter the
system files by system cracking, it may cause
system instability and security risks and threats.
注意
· 本机仅限使用JKRA电池
· 可能存在爆炸性气体时请勿更换电池
· 请勿在危险场所充电。
BE BGAT CY CZ DE DK EE ES FI
FR
GR HU IE IT LT LU LV MT NL PL PT
RO SE SI SK
UK
(NI)
RESTRICTIONS OF USE
This product may be used in the following European member states
subject to the following restrictions. For products that operate in the
frequency band 5.150 to 5.350 GHz, wireless access systems (WAS),
including radio local area networks (RLANs), shall be restricted to
indoor use.
This symbol means that it is forbidden to dispose the
product of with normal household waste. At the end of
the product life cycle, waste equipment should be
taken to designated collection points, returned to the
distributor when purchasing a new product, or contact
your local authority representative for detailed
information on WEEE recycling.
EU Representative :SUNMI France SAS
186,avenue Thiers,69006 Lyon,France
Technical features and characteristic
Operation Frequency Power（dBm）
824MHz-849MHz（TX)，869MHz-894MHz（RX）
880-915(TX),925-960(RX)
1710-1785(TX),1805-1880(RX)
1920-1980 MHz(TX), 2110-2170 MHz(RX)
880-915MHz(TX),925-960MHz (RX)
1920-1980 MHz(TX), 2110-2170 MHz(RX)
1710-1785 MHz(TX), 1805-1880 MHz(RX)
2500-2570 MHz(TX), 2620-2690 MHz(RX)
880-915MHz(TX),925-960MHz(RX)
832-862MHz(TX),791-821MHz(RX)
703-748MHz(TX),758-803MHz(RX)
2010-2025 MHz(TX), 2010-2025 MHz(RX)
2300-2400MHz(TX), (RX)
2402-2480MHz(TX/RX)
2402-2480MHz(TX/RX)
2412-2472MHz(TX/RX)
5150-5250MHz(TX/RX)
5745-5825MHz(TX/RX)
32.12
33.00
31.00
24.00
24.00
23.00
23.00
23.00
23.50
23.50
23.50
23.50
23.50
8.50
5.50
18.00
16.50
11.00
GSM850
GSM900
DCS1800
WCDMA Band I
WCDMA Band VIII
LTE Band 1
LTE Band 3
LTE Band 7
LTE Band 8
LTE Band 20
LTE Band 28
LTE Band 38
LTE Band 40
BT
BLE
2.4G Wifi
5G Wifi
FCC compliance statement
ISED Canada compliance statements
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Caution: The user is cautioned that changes or modifications not
expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
FCC ID: 2AH25T8A10
the device for operation in the band 5150-5250 MHz is only for
indoor use to reduce the potential for harmful interference to
co-channel mobile satellite systems;
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont
réservés uniquement pour une utilisation à l'intérieur afin de
réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux.
CE certification information (SAR)
EU regulatory conformance
Conformity CE
INFORMATION ABOUT THE SOFTWARE
Hereby,Shanghai Sunmi Technology Co., Ltd.declares that the
Wireless data POS System (Model NO .:T5F01）is in compliance
with the essential requirements and other relevant provisions of
RED 2014/53/EU.The full text of the EU declaration of conformity is
available at the following internet address：www.sunmi.com
RESTRICTIONS OF USE
This product may be used in the following European member
states subject to the following restrictions. For products that
operate in the frequency band 5.150 to 5.350 GHz, wireless
access systems (WAS), including radio local area networks
(RLANs), shall be restricted to indoor use.
The description of accessories and components, including
software, which allow the radio equipment to operate as
intended, can be obtained in the full text of the EU declaration
of conformity at the following internet address: www.sunmi.com .
CE certification information (SAR)
Certification information (SAR)
This device was tested for typical body-worn operations
with the back of the handset kept 0mm away. To maintain
compliance with RF exposure requirements, use
accessories that maintain a 0mm separation distance
between the user's body and the back of the handset. The
use of belt clips, holsters and similar accessories should not
contain metallic components in its assembly. The use of
accessories that do not satisfy these requirements may not
comply with RF exposure requirements, and should be
avoided.
If you are using pacemaker, hearing aid, cochlear implant
or other device, please use the phone according to the
doctor’s advice.
Product safety warnings
To prevent possible injury, please read all instructions
and safety information before you use the product.
Operating temperature: -20°C ~ 55°C,
Storage temperature: -40 °C ~ 70 °C.
Battery safety
Charge battery only at ambient temperatures ranging
from 0°C to 60°C.
(1) CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type of
battery recommended by the manufacturer.
Dispose of used batteries according to the battery
manufacturer’s instructions.
(2) CAUTION: RISK OF EXPLOSION IF BATTERY
IS REPLACED BY AN INCORRECT TYPE.
* The product information listed on this page may be updated from
time to time due to product upgrades or other reasons.SUNMI
reserves the right to modify the product information
and co- ntents on this page without notice.