Quick Start Guide

+
-
1
2
5
6
7
8
9
10
1
3
4
Scaning Button
Short press for scanning.
Volume Button
Press for adjusting volume.
PTT
Short press for network speaking.
Fn Button
Used for setting shortcuts.
Power Button
Short press: turn the screen on or off.
Long press: When the device is turned off, press and hold the
power button for 2 to 3 seconds to turn it on;
When the device is in use, press and hold the
power button for 2 to 3 seconds to turn it off or
restart it.
When the device crashes, press and hold the
power button for 11 seconds to make it reboot
automatically.
Scanner
Laser one-dimensional barcode scanner for reading information
Caution: In caseof the laser radiation, do not look straight at it.
Rear Camera
Support shooting and scanning 1D or 2D code rapidly.
Nano SIM Card Slot (optional)
Note: Turn off the phone before plugging or unplugging the
Nano SIM Card, or the malfunction might be caused.
（SIM card 2G/3G/4G full network access）
PSAM Card Slot (optional)
This place is used for plugging encryption PSAM CPU card.
Micro SD Card Slot (optional)
This place is used for plugging Micro SD Card.
1
2
3
4
5
6
7
8
9
10
Quick start
Back Cover Lock
Unlock the battery cover by lifting up the back cover lock and
rotating it.
Note: the battery cover must be installed on the device,
otherwise it will affect the normal use.
Strap Installation
① Thread the fixed part of the strap through the perforation at
the bottom of the device.
② Thread the fixed belt through the metal buckle in
accordance with the direction shown in the picture.
③ Fixed it with screws.
11
Strap Installation
Security Warning
Please insert the AC power plug into the AC power socket that
corresponds with the identifying input on the power adapter;
This device is a product grade A. It may cause radio
interference in the living environment.
About the replacement of battery:
① Replacing with wrong battery may cause explosion!
② Please hand the old battery to maintenance personnel,
and do not through it into fire.
Important Safety Instructions
Avoid the installation or usage during lightning, or there is a risk
of being harmed by lightning.
Please turn off the power immediately when you find suspicious
burning smell, overheating or smoke.
Statement
The company is not responsible for the following actions.
Damage of the product resulting from the use of the product
without in accordance with the user mannual;
For damage or problems of the product resulting from the
options or consumables( not the initial or approved product),
the company assumes no responsibilty. Without permission of
the company, no one is authorized to modify or alter the
product.
The operating system of the product supports official updating
of the system. The system instability and security risk may caused
by actions that users install the third-party ROM system or modify
the system files in cracked way.
Disclaimer
Due to the updating of the product, some details in the
document may not correspond with the product, and please in
kind prevail. The company shall be responsible for the
interpretation of the document, and reserve the right to modify
the manual without prior notice.
Notices
Table for Names and Content Identification of Toxic and
Hazardous Substances in this Product
Part Name
Toxic or Hazardous Substances and Elements
Pb Hg Cd
Cr(VII)
PBB PBDE
Circuit Board Component
Structural Component
Packaging Component
indicates that the content of the toxic and hazardous
substance in all homogeneous materials of the component
is below the limit specified in SJ/T 11363-2006.
indicates that the content of the toxic and hazardous
substance in at least one homogeneous material of the
component exceeds the limit stipulated in SJ/T 11363-2006.
However, as for the reason, because there is no mature and
replaceable technology in the industry at present.
：
：
The products that have reached or exceeded environmental
protection service life should be recycled and reused according
to the Regulations on Control and Management of Electronic
Information Products, and should not be discarded randomly.
Manufacture
Shanghai Sunmi Technology Co., Ltd.
Room 505 No.388 Song Hu Road Shanghai, China
T8A00 & T8A01_CN_EN_PVT_01
FCC certification information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: —Reorient or relocate the receiving antenna. —Increase the
separation between the equipment and receiver. —Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. —Consult the dealer or an
experienced radio/TV technician for help.
The smartphone is designed and manufactured not to exceed the emission limits for exposure
to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of
the U.S. Government when used as directed in the previous section. These limits are part
of comprehensive guidelines and establish permitted levels of RF energy for the general
population. The guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of scientific studies.
The exposure standard for wireless devices employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg*. Tests for SAR
are conducted using standard operating positions specified by the FCC with the device
transmitting at its highest certified power level in all tested frequency bands. Although the
SAR is determined at the highest certified power level, the actual SAR level of the device
while operating can be well below the maximum value. This is because the device is designed
to operate at multiple power levels so as to use only the power required to reach the network.
In general, the closer you are to a wireless base station antenna, the lower the power output.
The highest SAR value for this smartphone when tested for use at the ear is: 0.376W/Kg
The highest SAR value for this smartphone when tested in a holster with an integrated belt clip or
at a distance of 0.39 in. (10 mm) from the body, is: 0.974W/Kg
Body-worn measurements (recommended separation distances) differ among wireless
devices, including smartphones, depending upon supplied or available accessories and
applicable FCC requirements.
The FCC has granted an Equipment Authorization for this smartphone based on reported SAR
levels complying with the FCC radio frequency emission guidelines when the smartphone is
used as directed in this section. SAR information for this smartphone is on file with the FCC
and can be found under the Display Grant section of www.fcc.gov/oet/ea after searching for
the FCC ID for your smartphone listed below.
FCC ID:2AH25T8A01
T8A01
QUICK START GUIDE
Technical features and characteristic
the product includes the following features and characteristics：
Operation Frequency
824-849 MHz
1850-1910 MHz
1850-1910 MHz
1710-1755 MHz
824-849 MHz
1850-1910 MHz
1710-1755 MHz
824-849 MHz
2500-2570 MHz
699-716 MHz
704-716 MHz
1850-1915 MHz
814-849 MHz
2496-2690 MHz
2412-2462 MHz
2402-2480 MHz
2402-2480 MHz
13.56 MHz
Transmitted
32 dBm
30 dBm
24 dBm
24 dBm
24 dBm
23 dBm
23.5 dBm
24 dBm
24 dBm
24 dBm
20 dBm
23.5 dBm
23.5 dBm
24 dBm
20 dBm
9.5 dBm
1dBm
GSM 850
GSM 1900
WCDMA BAND II
WCDMA BAND IV
WCDMA BAND V
LTE BAND 2
LTE BAND 4
LTE BAND 5
LTE BAND 7
LTE BAND 12
LTE BAND 17
LTE BAND 25
LTE BAND 26
LTE BAND 41
WIFI
BT
BLE
NFC