K2 Kiosk User Manual Book Before using this product, please read this manual carefully and keep it properly.
Quick Setting Four installation styles of K2 Self-service Kiosk Only several steps to enable the smart commercial device K2： After turning on the complete machine power supply, the screen will be lit. Then you will enter the first boot interface and just simply operate according to the instructions. There are two types of internet mode available for you. LAN setting After plugging the network cable correctly, click “Setting” and “Wired Network” to choose Enable.
Quick Start Guide 5 5 1 6 3 2 1 Open the back plug cover. Plug the power line into the power interface. Plug the network cable into the network interface. 4 Close the back plug cover. 2 3 5 Press the buttons on both side of the host at the same time to open the flip panel. 6 Press the power switch to turn on the host.
Paper Changing Steps for the Inside Printer Brief Introduction of Self-Service Kiosk Indicator light Face camera Touch screen Trumpet Printer System switch Host switch 1 2 1 NFC Code scanner Nameplate 3 4 Face camera Camera used to shoot human face. Touch screen 1 2 Open flip panel Press the buttons on both side of the host at the same time to open the flip panel. 3 Open paper storage cover Toggle downward the printer driving lever to open the paper storage cover.
Installation Steps of the Four Types of Self-Service Kiosk Camera maintain cover Power supply switch Micro-USB debug port Protection cover on the mainboard Wired network interface USB interface Power interface Protection cover on the mainboard Micro-USB debug port Inside the host. Mainboard external interfaces, like USB port, TF card port, etc, will be exposed after opening it. On the mainboard and used for software update and debugging.
Installation Components 1 3 3 2 2 3 1 1 4 3 2 1 2 4 4 5 4 5 5 6 6 6 7 5 7 6 7 8 8 A Wall-mounted: 8 B Floor-standing: 1 Host 3 Mainboard maintain 4 Wall-mounted rack cover 5 Screw 2 6 Host back hanger Back plug cover 1 Host 2 C Floor-standing with table: Host back support Mainboard maintain 4 Back plug cover cover 5 Stand 6 Screw 3 7 Line cover 8 9 9 Baseplate 1 Host 2 Host back support Mainboard maintain 4 Screw cover 5 Back plug cover 6 Stand 3 7 Ta
A Installation Steps of Wall-mounted 280 283 1130 1 Drill holes on the wall Drill Ø10 holes according to the height and spacing described in the reference drawing. 2 Install the wall-mounted rack Firmly fix the wall-mounted rack on the wall by four M8X50 expansion bolts and four M6X50 expansion screws. 3 Install the host back hangers Fix the two host back hangers with host by four M6X12 screws; Plug in the power line and network cable.
B Installation Steps of Floor-standing 5 7 6 3 8 5 4 1 9 2 1 Preassemble the stand on the baseplate Preassemble the stand on the baseplate by two M10X20 screws and do not twist them too tightly. 3 Insert the host back support Insert the host back support into the stand. 2 Fix the stand on the baseplate Twist four M10X20 screws from the bottom of the plate as shown in the picture and fasten them. Then fasten the all the screws.
C Installation Steps of Floor-standing with Table (The same installation steps of the baseplate, stand and host with the Floor-standing) D Installation Steps of Eco-service expansion 1 12 11 10 2 10 Preassemble the table support screws Twist two M6X12 screws into the stand for 5-10 rounds. 11 Preassemble the table Hang the table support onto the two screws. 12 Fix the table Fix the table with stand by four M6X12 screws and fasten all the screws.
7 6 3 8 4 5 9 3 Insert host back support Insert the host back support into the stand. 4 Fix the back support with the stand Fix the back support with the stand by six M6x25 screws. 5 Fix the plastic front shell Fix the plastic front shell onto the metal stand again by clips. 6 Fix the host with back support Hang the host onto the back support and fix them by four M6X25 screws. 7 Assemble the mainboard maintain cover Fix the mainboard maintain cover on the host.
Basic Parameters of K2 Packing & Shipping Parameters of Complete Machine Operating system Android 7.1.2（SUNMI OS） Outline size Host: 394mm width × 171mm depth × 920mm height Processor Rockchip RK3399 Weight of machine Wall-mounted:17kg;Floor-standing:52kg;Floor-standing with table:56kg;Eco-service expansion:62.5kg Storage Memory:16G ROM+4G RAM Host packing:523mm width × 1110mm length × 371mm depth,weight:21.
Table for Names and Content Identification of Toxic and Hazardous Substances in this Product Part Name Toxic or Hazardous Substances and Elements Pb Hg Cd Cr(VI) PBB PBDE DEHP DBP BBP DIBP Circuit Board Component Structural Component Packaging Component ：indicates that the content of the toxic and hazardous substance in all homogeneous materials of the component is below the limit specified in SJ/T 11363-2006.
