SolarSwitch 4x PoE Smart MPPT Charger Model: SM-SW-40
Introduction Thank you for purchasing the Ubiquiti® SolarSwitch™ MPPT Charger. This Quick Start Guide is designed to guide you through installation and includes the warranty terms. Package Contents SolarSwitch NTC Thermistor 1U Bracket Ferrules (Qty.
Hardware Overview Battery and NTC Thermistor Terminal System LED PV Panel Terminal Reset Button Power Terminal Ethernet Ports PV Panel Terminal Output LED Note: NTC Thermistor must be connected in order for the battery to charge. Interface System LED Reset Button Description Steady on when system is powered on; Red when battery polarity is reversed. Press and hold the Reset button for 10 seconds to restore factory default settings.
Hardware Installation Note: Prior to use, it is recommended to write down the factory default password for this device. The password can be found on the sticker located underneath the SolarSwitch. Rack Mounting 1. Attach the 1U rackmount bracket (included) to either side of the SolarSwitch. 2. Mount the SolarSwitch to one of the side rails in your rack.
3. Remove the four-pin connector from the battery terminal block. 4. Crimp a ferrule on one end of the wire. 5. Insert the crimped wire into the appropriate slot on the four-pin connector. Using a flathead screwdriver, secure the wire to the connector by tightening the screw until it stops.
. Repeat steps four and five until the connector is fully occupied with all four wires. 7. Connect wires and NTC Thermistor to batteries. Note: The battery will not be charged without connecting the NTC Thermistor. 24VDC NTC Thermistor NTC Thermistor Note: Use SLA, AGM or Gel Lead batteries.
8. Attach the NTC and battery cable using the four-pin connector. 9. Attach the PV panel cables.
Connecting Ethernet 1. Connect Ethernet cable(s) to the Ethernet port(s). Note: PoE is disabled by default and can be enabled using the configuration interface. Configuration Connect to your LAN via Ethernet or Wi-Fi. Ethernet If connected to the LAN via Ethernet, the SolarSwitch will attempt to obtain an IP address automatically from a DHCP server. Use the Ubiquiti Device Discovery Tool to determine its IP address.
User Interface 1. Launch a web browser and enter the IP address of the SolarSwitch. Press Enter (PC) or Return (Mac). 2. Enter ubnt in the Username field. 3. Enter the password in the Password field (the password can be found on the sticker located under the port cover.) 4. Click Set Device Location to set the location for your solar system installation. 5. Click Power on the Settings screen and fill out the battery and solar panel information.
Enabling PoE To enable PoE on the SolarSwitch: 1. Click Output on the Settings screen. 2. Click the toggle button from OFF to ON, for each port you want to enable.
Specifications SM-SW-40 Dimensions Weight Enclosure Characteristics 168 x 136 x 36 mm (6.14 x 5.35 x 1.42") 543 g (1.2 lb) Steel, Indoor Use Max. Power Consumption Networking Interface Management Interface 2W (4) 10/100 Fast Ethernet Ports Ethernet + Wi-Fi (2.
Battery Charging Profile Trickle Charge Bulk Charge Absorption Charge Float Charge Maximum Charging Current Absorption Charge Voltage Float Voltage (95% of Absorption Charge Voltage) Battery Voltage Charging Current Charging Time % of Target Charging Voltage Battery Charging Profile Battery Temperature ( C) Absorption Charge Voltage Dependency from Temperature Note: Maximum charging current is limited by the power available from the solar panel and is not to exceed 7A.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1.
Limited Warranty ui.com/support/warranty The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
IMPORTANT NOTE: Radiation Exposure Statement: • This equipment complies with radiation exposure limits set forth for an uncontrolled environment. • This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. • This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities.
Français La directive européenne 2012/19/UE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI декларира, че това устройство SM-SW-40 е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/53/EC, 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: ui.
Ελληνικά [Greek] Δια του παρόντος, UBIQUITI, δηλώνει ότι αυτή η συσκευή SM-SW-40, είναι σε συμμόρφωση με τις βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις των οδηγιών 2014/53/EE, 2014/30/EE, 2014/35/EE. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: ui.
Slovenčina [Slovak] Týmto UBIQUITI, prehlasuje, že toto SM-SW-40 zariadenie, je v súlade so základnými požiadavkami a ďalšími relevantnými ustanoveniami smernice 2014/53/EÚ, 2014/30/EÚ, 2014/35/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: ui.com/compliance Slovenščina [Slovenian] Družba UBIQUITI izjavlja, da je naprava SM-SW-40 v skladu z obveznimi zahtevami in drugimi ustreznimi določbami direktiv 2014/53/EU, 2014/30/EU in 2014/35/EU.
Ubiquiti Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA Support help.ui.com Community community.ui.com Downloads downloads.ui.com ©2019 Ubiquiti Inc. All rights reserved. Ubiquiti, the Ubiquiti U logo, the Ubiquiti beam logo, sunMAX, SolarSwitch, TOUGHCable, and UNMS are trademarks or registered trademarks of Ubiquiti Inc. in the United States and in other countries. All other trademarks are the AJ120219 property of their respective owners.