ASSEMBLY INTRUCTIONS ITEM#:D-DN121-2 Table Warning Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use. Check all bolts for tightness before use, and periodically check and tighten bolts as necessary.
PARTS LIST Label Description QTY A Umbrella hole cover 1 B Top glass 1 C Top frame 1 D Leg 4 E Below fixed frame 1 F Support 2 HARDWARE PACK Label Description QTY AA Bolt M6×25 24 BB M6 Flat washer 24 CC Cap 24 DD Hex key M6 1 ASSEMBLY STEPS Step 1: Put bolt (AA) through flat washer (BB), attach below fixed frame (E) to leg (D) by hex key (DD). Do not lock tightly. Put on cap (CC) after locking all the bolts tightly.
Fig1 Fig 2 Step 3: As Fig 1 shows, put bolt (AA) through flat washer (BB), attach below fixed frame (E) to support (F) by hex key (DD). As Fig 2 shows, put bolt (AA) through flat washer (BB), attach support (F) to top frame (C) by hex key (DD). Lock all bolts tightly, then put on cap (CC). Step 4: Turn the table upright, put top glass (B) on top frame (C), then put umbrella hole cover (A) onto umbrella hole. Assembly finished.
Care & Maintenance: Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Steel components of garden accessories and furniture are treated with rust inhibiting paint. However, due to the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched.
ASSEMBLY INTRUCTIONS ITEM#:D-DN121-2 Chair Warning Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use. Check all bolts for tightness before use, and periodically check and tighten bolts as necessary.
PARTS LIST Label Description QTY A Back 1 B Left armrest 1 C Right armrest 1 D Seat board 1 E Back cushion 1 F Seat cushion 1 HARDWARE PACK Label Description QTY AA Bolt M6×20 10 BB M6 Spring washer 10 CC M6 Flat washer 10 DD Cap 8 EE Hex key M6 1 FF Foot pad (pre-assembled) 4 ASSEMBLY STEPS Step 1: Attach seat board (D) to back (A) by bolt (AA), spring washer (BB), flat washer (CC) and hex key (EE). Do not lock tightly.
Step 3: Put bolt (AA) through spring washer (BB), flat washer (CC), attach armrest (B, C) to back (A) by hex key (EE). Do not lock tightly. Step 4: Put seat cushion (F) onto seat board, stick hook-and-loop fasteners, put back cushion (E) on back. Care & Maintenance: Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely.
ASSEMBLY INTRUCTIONS ITEM#:D-DN121-2 Swivel Warning Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use. Check all bolts for tightness before use, and periodically check and tighten bolts as necessary.
PARTS LIST Label Description QTY A Back 1 B Left armrest 1 C Right armrest 1 D Seat board 1 E Base 1 F Back cushion 1 G Seat cushion 1 HARDWARE PACK Label Description QTY AA Bolt M6x20 10 BB M6 Spring washer 10 CC M6 Flat washer 10 DD Screw M8x40 4 EE Screw M8x35 (pre-assembled) 4 FF M8 Nut( 4 pre-assembled) 8 GG M8 Spring washer (4 pre-assembled) 8 HH M8 Flat washer ( 4 pre-assembled) 8 II Big washer (2 pre-assembled) 6 JJ Spring steel plate (pre-assem
Step 2: Attach armrest (B/C) to seat board (D) by bolt (AA), spring washer (BB), flat washer (CC) and hex key (MM). Put on cap (KK) after locking all bolts tightly. Step 3: Put bolt (AA) through spring washer (BB), flat washer (CC), attach armrest (B, C) to back (A) and hex key (MM). Do not lock tightly.
Step 5: Put seat cushion (G) onto seat board, stick hook-and-loop fasteners, put back cushion (F) on back. Assembly finished. Care & Maintenance: Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Steel components of garden accessories and furniture are treated with rust inhibiting paint.