User Manual

ManualsBrandsSunFounder ManualsComputers & AccessoriesRaspberry Pi 10 Inch Touch Screen - 10.1" HDMI 1280x800 IPS LCD Touchscreen for RPi 400 4 Model B 3 Model B+ 3B 2B LattePanda Beagle Bone

Content

SunFounder 10.1'' Touch Screen ....................................................... 1

Introduction .................................................................................... 1

Features ........................................................................................... 2

Functions Description .................................................................. 2

Installation ....................................................................................... 4

Install the Virtual Keyboard ...................................................... 10

Using as Extension Screen for PC ............................................ 10

3D-printed touch screen support ........................................... 11

SunFounder 10.1'' Touch Screesn

Introduction

This SunFounder 10.1'' IPS monitor is a 10-point capacitive touch screen

with a resolution of 1280x800, bringing you perfect visual experience. It

works with various operating systems including Raspbian, Ubuntu, Ubuntu

Mate, Windows, Android, and Chrome OS(you may need an USB

extension cable).

Summary of content (14 pages)

PAGE 1
Content SunFounder 10.1'' Touch Screen ....................................................... 1 Introduction .................................................................................... 1 Features ........................................................................................... 2 Functions Description .................................................................. 2 Installation .......................................................................................
PAGE 2
Features Functions Description Indication Lights There are 2 LED indicators on the main board of the screen to show different signals: Power on the screen and both the 2 LEDs will light up immediately. If there's no HDMI signal, then only the green LED will be on. If there's an HDMI signal, then only the red LED will be on.
PAGE 3
Press and hold the switch to power off the display, and both LEDs will be off. If you press the switch to sleep the device, the red LED will be on. Buttons s Buttons on the main board and their functions: a. Power Press and hold to switch it off Press to sleep/awake the device b. Menu To show menus To confirm c. VTo go down on the Menu interface Volume down on other interfaces d. V+ To go up on the Menu interface Volume up on other interfaces d.
PAGE 4
On one side of the main board there are ports for HDMI input, 12V power input, and 5V/2A USB power output. On the other side, you can see ports for 30-pin LVDS ribbon cable, 6-pin backlight control and 4-pin speaker. Installation The screen comes with seven 2.5*14.4 standoffs, two 2.5*22 ones, seven 2.5*6 ones, and some nuts for installing the Raspberry Pi to the screen. Take the following steps to complete the assembly. Step 1. Fix the main board to the screen. Place the main board onto the 4 2.
PAGE 5
Insert the 2.5*14.4 standoffs into the holes and tighten them. Step 2. Fix the Raspberry Pi (or other boards) on the screen back case. There are a vertical slot and a horizontal one on the back of the screen, so you can fix boards with different sizes by moving the nuts and 2.5*6 standoffs with the small wrench.
PAGE 6
If you want to use a Raspberry Pi with the screen, then you don't need to adjust the standoffs since they are preset for it. Just place the board onto the case with holes on the RPi and the standoffs aligned, insert the 2.5*14.4 standoffs and fasten them. Step 3. Insert the two 2.5*22 standoffs into the holes on the back to keep the screen balanced.
PAGE 7
Step 4. Wiring. 1) Plug in the 6-pin backlight control cable into the LED BS port.
PAGE 8
3) Connect the power port of the RPi to the USB port of the main board via a USB cable. 4) Connect the HDMI port of the RPi and the screen via an HDMI cable. 5) Connect the USB port of the RPi and the screen with a 4-pin USB cable. 6) To prevent the cable from falling off, use tape to fix it.
PAGE 9
7) Connect the power cable of the supply to power the main board of the screen. Then power it on and the boot screen will appear.
PAGE 10
Install the Virtual Keyboard Open a terminal and run the command: sudo apt-get install matchbox-keyboard After the installation is done successfully, the keyboard is in the system menu,open as follows: Using as Extension Screen for PC Connect the computer and the main board via an HDMI cable, and the USB port of the PC and the screen with a 4-pin USB cable(you may need an USB extension cable for connection). Now you can use the screen as an extension one for your computer.
PAGE 11
3D-printed touch screen support If you need to place the touch screen more conveniently, you can use a 3D printer to print a support. The relevant files required by the 3D printer are in our official website http://wiki.sunfounder.cc/index.php?title=File:Stand.zip, process is as follow. 1.
PAGE 12
2.
PAGE 13
3.
PAGE 14