Operator’s Manual SB-HDWT Wireless HD Transceiver
Contents 1. Important Information 1.1 Warranty 1.2 Safety Precautions 1.3 Warning: Protect Transmitter From Heat/Moisture 1.4 Declaration of Conformity 1.5 Avoiding Radio Interference 3 3 3 4 4 4 2. Introduction 2.1 Product Overview 2.2 Product Features 2.3 Package Content 2.4 HDWT-Tx Transmitter Controls and Connections 2.5 HDWT-Rx Receiver Controls and Connections 5 5 5 5 6 6 3. Installation and Operation 3.1 Connect the HDWT-Tx Transmitter 3.2 Connect the HDWT-Rx Receiver 3.
1. Important Information Take time to read this user manual before using the SB-HDWT Wireless HD Transceiver. This manual contains important information and instructions regarding operating your wireless HDWT-Tx (transmitter) and HDWT-Rx (receiver). 1.1 Warranty Your SB-HDWT is under limited warranty by SunBriteTV, provided the product is handled properly for intended use, in accordance with its operating instruction.
1.3 Warning: Protect Transmitter From Heat/Moisture ●● The transmitter should not be exposed to rain or moisture. Do not place objects filled with liquids, such as vases, on or near the transmitter. ●● Install the transmitter in a property ventilated area, away from direct sunlight or any source of heat. 1.4 Declaration of Conformity This device complies with Part 15C and Part 15E of FCC Rules. Part 15: Subpart C—Radiated Emission Limits, Additional Provisions.
2. Introduction 2.1 Product Overview The SB-HDWT wireless system contains two main components: the HDWT-Tx transmitter and the HDWT-Rx receiver. The system transmits uncompressed video signals with resolution up to 1080p/60Hz with accompanying stereo audio. The HDWT-Tx transmitter connects via HD cable to standard video sources including a cable box, satellite receiver, Internet streaming box (Apple TV, Roku, etc.
2.4 HDWT-Tx Transmitter Controls and Connections FRONT PANEL 1. Power LED: Indicates that unit is powered 2. Video LED: Indicates that active HD source is connected 3. Link LED: Indicates wireless connection between HDWT-Tx and HDWT-Rx receiver 4. USB Interface: Used for PC connection or other USB device, such as a keyboard BACK PANEL 5. IR IN: Connects to the supplied IR emitter 6. Reset button: Press to reset wireless connection. Holding this button down for more than 5 seconds will turn the unit off.
3. Installation and Operation 3.1 Connecting the HDWT-Tx Transmitter You can lay the transmitter flat or mount it upright on its stand. Make sure it’s placed a couple of feet away from the other electronics. Avoid putting it inside a cabinet, which will reduce the range of the transmitter. Connect the included 6-foot HD cable to the back of the transmitter, then to the HD output of a Blu-ray player, DVD player, cable box or satellite receiver. Make sure the device is powered up and playing.
Connect the included 15-foot HD cable to the HD jack on the underside of the receiver. Connect the other end to one of the HD inputs on the TV. Turn on the TV and select the HD input you used to connect the receiver. Now plug the included AC cord into the AC power input on the underside of the receiver, near the HD jack. Plug the other end of the power cord into a wall outlet or power strip. All three green LEDs on the front of the transmitter and the receiver, marked Power, Video and Link, should light up.
3.5 Setting Up for Multiple Transmitter Operation The HDWT-Rx receiver can be used with multiple HDWT-Tx transmitters, which are available separately from your SunBriteTV dealer or distributor. With multiple transmitters set up, you will be able to use mulitple source devices and switch among them using the Source button on the included remote control. ADDING A TRANSMITTER To add a second (or third, fourth, etc.) transmitter to the system, first connect the source to the transmitter with an HDMI cable.
3.6 Connecting a USB Keyboard and/or Mouse The SB-HDWT system can transmit signals from a USB keyboard connected to the HDWT-Rx receiver to a computer connected to the HDWT-Tx transmitter. This arrangement may come in handy if you are using the SB-HDWT system to transmit HD video from a computer, or if you wish to browse the web through the TV connected to the system. A wireless keyboard and mouse using a USB dongle works well.
4. Product Specifications GENERAL SPECIFICATIONS Model HDWT-Tx HDWT-Rx Supported video frequencies 1080p, 720p, 1080i, 576p, 480p, 480i, 576i HDMI port Supports HDMI1.3 audio format and encrypted video format HDCP 2.0 Transmission distance 100 feet / 35 meters System latency <1 ms Antenna Built-in omnidirectional antennas Operating frequency 4.9 - 5.9 GHz Power supply 100 - 240V alternating current input, 5V 2.5/3A direct current power adaptor Certificates FCC Part 15 Standard WHDI 1.
5. Troubleshooting Before following the troubleshooting guide below, please make sure that transmitter, receiver, source equipment and display equipment are all switched on and properly connected. In normal operation, the Video LED on the receiver will be off (it is on only during the connection process.) The Power, Video and Link LEDs on the transmitter and the Power and Link LEDs on the receiver will glow steady green. No picture 1.
6. FCC ID Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
