User manual Model:F2 Brand:NUU
Follow these step-by-step instructions to set up your F2. Power off the phone and remove battery before inserting any cards! Remove Back Cover Insert SIM (Dual SIM Standby) Orient SIM card to match diagram on slot. SIM 1 (Mini) supports GSM connections. SIM 2 (Mini) supports GSM connections. Remove the back cover by prying the back cover up with your fingers. Insert microSD™ Memory Card Insert the Battery Power off the phone and remove battery before inserting memory card.
THANK YOU! For Your Purchase of the F2 AB C GH I PQRS DEF JK L MN O TUV WXYZ
Earpiece LCD Screen The Keypad Menu Contacts/Back AB C DEF Arrow Keys GH I JK L MN O Menu/Action PQRS T UV WXYZ Answer Call End Call/Power On/Off Hold 1 for Voicemail Call Holding # key swaps between GENERAL and SILENT mode microUSB connector Microphone AUX-In/Headset jack
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Specific Absorption Rate (SAR) information: This Mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies.
these requirements may not comply with FCC RF exposure requirements, and should be avoided. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components.
IC Warning This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. RF Exposure Information and Statement The SAR limit of USA is 1.6 W/kg averaged over one gram of tissue. Device types: Mobile phone (IC: 20782-NUUF2) has also been tested against this SAR limit.
Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement RF exposition Information et Déclaration La limite SAR des Etats-Unis est de 1,6 W / kg en moyenne par gramme de tissu.
Porté au corps Opération Ce dispositif a été testé pour les opérations typiques portés sur le corps. Pour se conformer aux exigences d'exposition aux radiofréquences, une distance de séparation minimale de 10mm doit être maintenue entre le corps de l'utilisateur et le combiné, y compris l'antenne. Tiers pinces de ceinture, étuis et autres accessoires similaires utilisés par ce dispositif ne doit pas contenir de composants métalliques.