SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE SUMMIT SEMICONDUCTOR LLC Model No.: 444-2196H FCC ID: UA9300 USER MANUAL Issue Date: 10 October, 2010 Revision: 1.0 Revision History Rev. No. 1.0 History Draft Release Model No. 444-2196H www.summitsemi.com Issue Date 10 October, 2010 Remarks Pending FCC Grant 22867 NW Bennett St.
SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE COPYRIGHT 2010 SUMMIT SEMICONDUCTOR LLC ALL RIGHTS RESERVED THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROTECTED BY COPYRIGHT LAWS OF THE UNITED STATES OF AMERICA AND OTHER COUNTRIES. IT MAY NOT BE REPRODUCED OR DISTRIBUTED IN ANY FORM BY ANY MEANS, ALTERED IN ANY FASHION, OR STORED IN A DATA BASE OR RETRIEVAL SYSTEM, WITHOUT EXPRESS WRITTEN PERMISSION OF SUMMIT SEMICONDUCTOR LLC.
SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE Table of contents 1.0 Regulatory Statement …………………………………………………...4 1.1 FCC Certification…………………………………………………4 2.0 Introduction……………………………………………………………...5 3.0 Installation and Test procedure……………………….…………………8 3.1 Boot 3.2 Setting frequency channel, data rate and transmit power 3.3 Stop Transmitting 4.0 System Requirements…………………………………………………..13 Model No. 444-2196H www.summitsemi.com 3 of 13 © 2010 Summit Semiconductor LLC 22867 NW Bennett St.
SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE 1.0 Regulatory Statement The United States Federal Communication Commission has established certain rules governing the use of electronic equipment. 1.1 FCC Certification This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE 2.0 Introduction: The 444-2196H Wireless Audio Client device is a production ready module designed for active speakers in Summit Semiconductor’s wireless audio technology. The module mounts to the top interior wall of a typical speaker. The module includes a patented, low cost, high gain quad diversity PCB antenna integrated in the module to provide superior wireless performance without external antennas.
SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE FRONT SIDE Model No. 444-2196H www.summitsemi.com 6 of 13 © 2010 Summit Semiconductor LLC 22867 NW Bennett St.
SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE BACK SIDE CAUTION: DO NOT TRY TO REPLACE THE ANTENNAS Model No. 444-2196H www.summitsemi.com 7 of 13 © 2010 Summit Semiconductor LLC 22867 NW Bennett St.
SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE 3.0 Installation and Test Procedure A host interface board is used to provide the necessary regulated power supply to the 444-2196H Wireless Audio Client device. The set up is as shown in the picture below. 8 7 9 5 6 1 4 2 3 Model No. 444-2196H www.summitsemi.com 8 of 13 © 2010 Summit Semiconductor LLC 22867 NW Bennett St.
SUMMIT SEMICONDUCTOR LLC 1 2 3 4 5 6 7 8 9 AUDIO WIRELESS CLIENT DEVICE Wireless Audio Client device Integrated Antenna RF Can Multi pin flex cable Hermiston (Interface Board) Power Input 3.3V Reset button RS232 interface Serial cable 3.1 Boot: . ¾ Download Summit Semiconductor’s Hood_BIST_0013 software onto your computer. ¾ Connect a multi pin flex cable from Hermiston (interface board) to 444-2196H Wireless Audio Client device as shown in the picture. ¾ Connect a 3.
SUMMIT SEMICONDUCTOR LLC Model No. 444-2196H www.summitsemi.com AUDIO WIRELESS CLIENT DEVICE 10 of 13 © 2010 Summit Semiconductor LLC 22867 NW Bennett St.
SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE 3.2 Setting Channel, data rate and transmit power The following transmit command is used to set the transmitter in a particular channel and to start transmitting. tx -1 1 d 4 8 255 The parameters in the command are explained below.
SUMMIT SEMICONDUCTOR LLC 24 25 26 27 28 29 30 31 32 33 34 AUDIO WIRELESS CLIENT DEVICE 5600 5620 5640 5660 5680 5700 5745 5675 5785 5805 5825 Example: 1) tx -1 1 d 4 8 255 ; The DUT transmits in frequency 5180 MHz 2) tx -1 1 d 4 30 255; The DUT transmits in frequency 5745 MHz 3.3 Stop transmitting The following command is used to stop the DUT from transmitting. stoptx Model No. 444-2196H www.summitsemi.com 12 of 13 © 2010 Summit Semiconductor LLC 22867 NW Bennett St.
SUMMIT SEMICONDUCTOR LLC AUDIO WIRELESS CLIENT DEVICE 4.0 System Requirements Operation: PC with COM ports Programming: Windows XP and higher Model No. 444-2196H www.summitsemi.com 13 of 13 © 2010 Summit Semiconductor LLC 22867 NW Bennett St.