Suga Electronics Limited Model: SWBGFSA-0 WiFi/Bluetooth/GPS 3-in-1 Combo Module User Guide Version: 1.0 Jun 2014 © Suga Electronics Limited. All Rights Reserved. Information in this document is subject to change without prior notice. P.
Suga Electronics Limited 1 Hardware Installation ……………………………...….. 3 1.1 Mechanical Drawing ……………………………………….……… 3 1.2 Pins Assignment ………………………………………………….... 3 1.3 Hardware Installation Procedures ……………………………..… 4 2 Software Installation ………………………….……….. 5 2.1 COM port check …………………………………….........………… 5 2.2 Software Configuration Tools ……………………………………… 5 2.3 2.4 Configuration for GPS …………………………………………….. Configuration for BT ………………………………………………. 7 8 2.
Suga Electronics Limited 1. Hardware Installation 1.1 Mechanical Drawing Figure1. Mechanical dimension 1.2 Pins Assignment Please refer to the datasheet about the details of the pin assignment. Pin# definition Description 1 ANT_WIFI_BT WIFI/BT RF input/output port 2, 13, 23 GND GND 14 VCC3.3V 3.3V power supply 3~8 SD_D[3:0], CMD, CLK SDIO data pins.
Suga Electronics Limited 1.3 Hardware Installation Procedures Example of Installation procedures: 1. Disconnect from any power supply. 2. Solder firmly the module onto the host system board. 3. For best performance, have the Wifi+BT chip antenna located as far away as possible from any metal. 4. Connect the GPS antenna to the module via coaxial cable to the GPS RF connector on the module. 5.
Suga Electronics Limited 2. Software Installation 2.1 COM port check Under Windows, run Device Manager. Check the physical COM port assignment. For example as in below picture, the COM port is COM7. 2.2 Software Configuration Tools (1) Run “Lab Tool for WiFi V1.30” confiuguration tool. Check that the virtual COM port (WMT, BT, GPS) is same as those in below picture. (2) Fill into the PHY port the correct physical COM port (COM7). Click Enable. (3) Put the patch file “Patch_e3_20120405.
Suga Electronics Limited © Suga Electronics Limited. All Rights Reserved. Information in this document is subject to change without prior notice. P.
Suga Electronics Limited 2.3 Configuration for GPS (1) Create a hyper-terminal under Windows. Select COM35. Configure 115200-8-N-1 to view GPS data. (2) Open “GPS MNL Decoder”. Select Set/Unset, Enable/Disable to enable/disable the GPS decoder. (3) Wait a few seconds. GPS data will be given out to the hyper-terminal. © Suga Electronics Limited. All Rights Reserved. Information in this document is subject to change without prior notice. P.
Suga Electronics Limited 2.4 Configuration for BT (1) Open “Lab Tool for Bluetooth V1.6”. (2) Fill in 32 to COM port. Select Open. (3) Configure BT package type, modulation, channel, etc. © Suga Electronics Limited. All Rights Reserved. Information in this document is subject to change without prior notice. P.
Suga Electronics Limited © Suga Electronics Limited. All Rights Reserved. Information in this document is subject to change without prior notice. P.
Suga Electronics Limited 2.5 Configuration for Wifi (1) Click Enable/Disable to enable/disable Wifi. (2) Confirm that the log area reported successful. (3) Configure desired channel, mode, etc. © Suga Electronics Limited. All Rights Reserved. Information in this document is subject to change without prior notice. P.
Suga Electronics Limited 3. Trouble-shooting In case the software configuration has any problem, please check below settings. (1) Under Windows, run Device Manager. Check the correct Physical COM port. Different computer has different COM port. (2) Check that Virtual COM installation is correct. © Suga Electronics Limited. All Rights Reserved. Information in this document is subject to change without prior notice. P.
Suga Electronics Limited (3) Check that there are 6 Virtual COM pairs installed as in below pictures. (4) Check that the Secure Digital Host Controllers is installed correctly. © Suga Electronics Limited. All Rights Reserved. Information in this document is subject to change without prior notice. P.
Suga Electronics Limited 4. Disclaimer Suga Electronics Limited (SugaE) assumes no responsibility for errors or omissions in the materials available on this Document. THESE MATERIALS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED , INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT.
Suga Electronics Limited 6. FCC Information FCC caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; 2. This device must accept any interference received, including interference that may cause undesired operation.
