INSTALLATION GUIDE Built-In Panel Mounting Kit
Built-In Panel Mounting Kit 2 Contents Built-In Panel Mounting Kit 3 Mounting Instructions 4 Model BI-36R / BI-36F 5 Model BI-30U 6 Model BI-36U 7 Model BI-36UFD 8 Model BI-42UFD 9 Model BI-36S 10 Model BI-42S / BI-42SID / BI-42SD 11 Model BI-48S / BI-48SID / BI-48SD 12 Model BI-36R / BI-36F—Dual Installation 13 Model BI-30U—Dual Installation 15 Model BI-36U—Dual Installation 17 Features and specifications are subject to change at any time without notice. Visit subzero.
Built-In Panel Mounting Kit 3 subzero.com/specs Built-In Panel Mounting Kit OVERLAY AND FLUSH INSET PANELS PANEL MOUNTING KIT CONTENTS: The panel mounting kit consists of stock lengths of PVC cleats, self-drilling mounting screws and offset gages for correctly locating the mounting cleats on the back of decorative panels (overlay and flush inset). Each Sub-Zero built-in model has a page in this guide which provides the cut length of each cleat and offset required for mounting.
Mounting Instructions 4 Mounting Instructions 1) Determine location and mounting method of custom door handle if one will be used. Decide the best way to modify the cleat for the handle if necessary (cut cleat completely or notch to fit). Also, determine the best sequence for installing handle and cleat. Panel will need to overhang the work surface if handle is installed before cleating. 2) Provide surface protection and lay decorative panel on a flat work surface with finished side down.
Model BI-36R / BI-36F 5 subzero.com/specs Model BI-36R / BI-36F SINGLE INSTALLATION Cleat Cut Length Mounting kit is not intended for use with glass door model. The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application.
Model BI-30U 6 Model BI-30U SINGLE INSTALLATION Cleat Cut Length Mounting kit is not intended for use with glass door model. The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application. Grille (83" or 84" finished height) Grille (88" finished height) Refrigerator Freezer PANEL IMPORTANT NOTE: Panels are viewed from the front to show finished elevation.
Model BI-36U 7 subzero.com/specs Model BI-36U SINGLE INSTALLATION Cleat Cut Length Mounting kit is not intended for use with glass door model. The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application.
Model BI-36UFD 8 Model BI-36UFD SINGLE INSTALLATION Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application.
Model BI-42UFD 9 Model BI-42UFD SINGLE INSTALLATION Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application.
Model BI-36S 10 subzero.com/specs Model BI-36S SINGLE INSTALLATION Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application. Grille (83" or 84" finished height) Grille (88" finished height) Refrigerator Freezer IMPORTANT NOTE: Panels are viewed from the front to show finished elevation. Cleats will be attached to the back of the panels.
Model BI-42S / BI-42SID / BI-42SD 11 Model BI-42S / BI-42SID / BI-42SD SINGLE INSTALLATION Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application. Grille (83" or 84" finished height) Grille (88" finished height) Refrigerator Freezer IMPORTANT NOTE: Panels are viewed from the front to show finished elevation.
Model BI-48S / BI-48SID / BI-48SD 12 subzero.com/specs Model BI-48S / BI-48SID / BI-48SD SINGLE INSTALLATION Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application. Grille (83" or 84" finished height) Grille (88" finished height) Refrigerator Freezer IMPORTANT NOTE: Panels are viewed from the front to show finished elevation.
Model BI-36R / BI-36F—Dual Installation 13 Model BI-36R / BI-36F—Dual Installation SEPARATE GRILLES Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application. Grille (83" or 84" finished height) Grille (88" finished height) Door IMPORTANT NOTE: Panels are viewed from the front to show finished elevation.
Model BI-36R / BI-36F—Dual Installation 14 subzero.com/specs Model BI-36R / BI-36F—Dual Installation DUAL WIDE GRILLE Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application. Grille (83" or 84" finished height) Grille (88" finished height) Door IMPORTANT NOTE: Panels are viewed from the front to show finished elevation.
Model BI-30U—Dual Installation 15 Model BI-30U—Dual Installation SEPARATE GRILLES Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application.
Model BI-30U—Dual Installation 16 subzero.com/specs Model BI-30U—Dual Installation DUAL WIDE GRILLE Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application.
Model BI-36U—Dual Installation 17 subzero.com/specs Model BI-36U—Dual Installation SEPARATE GRILLES Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application.
Model BI-36U—Dual Installation 18 subzero.com/specs Model BI-36U—Dual Installation DUAL WIDE GRILLE Cleat Cut Length The illustrations below provide panel dimensions and mounting cleat offsets for overlay and flush inset panels. Check dimensions of actual panels against the illustration for your panel application.
SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 7028798 REV-A 6 / 2013 SUBZERO.COM 800.222.