User's Manual

ManualsBrandsStyling city industries ManualsElectronicsWireless Doorbell Receiver w/ Digital Clock

Wire Free Portable Door Chime Kit with Indoor Time Station Model: SC-352

No wiring is required for this Wire Free Door Chime Kit. When the Push Button is pressed, it sends

a wire free signal to the door chime unit that activates the chime. As the operation range is upto

30metres (100ft. approx. – in open field), you can mount or take the door chime virtually anywhere

in the home. However, the transmission range of the wire free signal will be reduced if the signal is

transmitted through a number of walls or ceiling. Metal and UPVC doorframes will also reduce the

operating range.

Battery Installation

Push button unit

1. Push button unit is operated by 1 x 3volt CR2032 Lithium batteries (included)

2. 1 x 3volt CR2032 Lithium batteries (included) have been installed, it is ready to use.

Replace the batteries: Remove the locking screw from the battery fastener of the battery

compartment. Insert 1 x 3volt CR2032 Lithium batteries in the battery compartment, ensuring the

battery polarity match the internal markings, then tighten the screw on the battery fastener to hold

the batteries firm in it’s compartment.

Portable Door Chime unit

1. Open the battery cover from the back of the unit.

2. Insert 2 x 1.5volt alkaline batteries (“AA”, UM3 & LR6 – not include) into the battery

compartment, ensuring the battery polarity match the internal markings.

3. It will beep twice to indicate that it is ready to use and learn the operation code (Please see

Digital Code Set Up).

4. Close the battery door, then the chime unit is ready to use.

Installation Guide

a) Push Button Unit: Using the two holes of the back of push button as a template, mark the fixing

position for the unit. Drill holes and fit wall plugs and secure the Bell Push Unit with screws

(self-tapping 3 x 16mm screw) in position, or by the double-sided self-adhesive pad (included),

onto your front door or the position nearby.

Important: Mounting the Push Button unit on the UPVC doorframes or metal surface will

reduce the broadcasting range seriously.

b) Door Chime Unit: It has a slotted hang hole on the rear behind the belt clip, this will enable the

Chime unit to be hooked onto a screw and easily removed or relocated to another room.

Drill hole and fit wall plug (if fixing to masonry) and screw (self-tapping 3 x 16mm screw) to

fixing position. Leave a gap of 3mm between the screw head and the wall. Locate the keyhole

slot on the back of the unit over the screw.

The Chime unit can also be free standing and you can place it on any desk in the house.

Summary of content (6 pages)

PAGE 1
Wire Free Portable Door Chime Kit with Indoor Time Station Model: SC-352 No wiring is required for this Wire Free Door Chime Kit. When the Push Button is pressed, it sends a wire free signal to the door chime unit that activates the chime. As the operation range is upto 30metres (100ft. approx. – in open field), you can mount or take the door chime virtually anywhere in the home.
PAGE 2
Melody Selection The Melody Selector is located inside the push button unit. It is a small button on the top left corner of battery compartment marked with “S”. Press the switch once, the melody will change to the next one on the list, there are total 8 melodies for selection. The Push Button is pre-set to “Westminster” therefore, if no change is required, it should not be adjusted.
PAGE 3
Time Station Battery Installation 1. Open the battery compartment door at the back of the unit by sliding it away from the unit. 2. Insert 2 x 1.5volt batteries (“AA”, UM3 & LR6 – not included). 3. A melody will be heard to indicate that it is in operation. 4. Close the battery door and it is ready to use. Function This item has the following functions: 1. Digital Clock 2. Calendar 3. Alarm Clock 4. Birthday Reminder 5. Countdown Timer 6.
PAGE 4
12hrs / 24hrs * When in normal working mode, simply press the “Up” & “Down” button to change the time from 12hrs to 24hrs. Alarm Clock Mode * Press the Alarm button to enter the alarm clock mode * Use the Set and “up” & “down” buttons to set time and alarm sound * There is total 7 different alarm sounds for selection. * Use “up” button to switch on the snooze function when alarm function is on * Alarm will sound at the set time for 1 minute.
PAGE 5
. 6. 7. Do not use different type if batteries, or mix up old and new batteries. Always use alkaline batteries as these will give longer service and are less likely to leak. If leaving the doorbell for long period of time, remove the battery from compartment to prevent leakage. 8. 9. Door Chime unit is designed for indoor use only. Please dispose of old, defective batteries in an environmentally friendly manner in accordance with the relevant legislation. 10.
PAGE 6
Specification A. Push Button unit Power : 1 x 3volt Lithium batteries (CR2032– included) Consumption : 2.0mA - ON 0.001mA – OFF B. Door Chime unit Power : 2 x 1.5volt alkaline batteries (“AA”, UM3 & LR6 – not included) Consumption : 100mA – ON 0.35mA - Stand By C. Time Station Power : 2 x 1.5volt alkaline batteries (“AA”, UM3 & LR6 – not included) Consumption : .01mA Operating Temperature : -10C – +40C Operating Distance : 30metre (100ft approx.