User's Manual

ManualsBrandsStyling city industries ManualsElectronicsWireless Doorbell Transmitter

Wire Free Door Chime Kit Model No.: SC335T

No wiring is required for this Wire Free Door Chime Kit. When the Push Button is pressed, it sends a

wireless signal to the door chime that activates the chime.

Since the operating range is up to 150ft (50metre approx. – in open field & at suitable condition), you

can mount or take the door chime virtually anywhere in the home, workshop, office or garden.

However, the transmission range of the wire free signal will be reduced if the signal is transmitted

through a number of walls or ceilings. Metal and UPVC doorframes will also reduce the operating

range.

Battery Installation

Push Button unit

1. Push button unit is operated by 1 x 3volt Lithium battery (CR2032 - included)

2. The Lithium battery (CR2032) has been installed. Open up the push button and remove the

isolation strip from the battery compartment then it is ready to use.

Replace the battery. Use a small flat screwdriver to lift up the battery from the battery compartment.

Replace it by 1 x 3volt CR2032 Lithium battery, ensuring the battery polarity match the internal

markings (“+” face upward), then press the battery down so that it is sitting firmly in its compartment.

Snap the back cover of Push Button back on.

Portable Door Chime unit

1. Remove the battery cover from the back of the unit by sliding it away from the unit.

2. Insert 2 x 1.5volt alkaline batteries (“AA”, UM3 & LR6 – not include) into the battery

compartment, ensuring the battery polarity match the internal markings.

3. It will beep twice to indicate that it is ready to use and learn the operation code (Please see

Digital Code Set Up).

4. Close the battery door, then the chime unit is ready to use.

Installation Guide

a) Push Button Unit: Using the two holes at the back of bell push as a template, mark the fixing

position for the unit. Drill holes and fit wall plugs (if fixing to masonry) and secure the push button

unit with screws onto your front door or the position nearby.

Important: Do not mount the Push Button unit on the UPVC doorframes or metal surface, it will

reduce the broadcasting range seriously.

b) Door Chime Unit: This chime unit can be completely portable or fixed in one place. It has a

slotted hang hole on the rear and it can be easily removed or relocated to another room.

Drill a hole and a fit wall plug (if fixing to masonry) and screw (self-tapping 3 x 16mm screw) to

fixing position. Leave a gap of 3mm between the screw head and the wall. Locate the keyhole slot

on the back of the unit over the screw.

Important: Operate the Chime unit within the operation range, test it before final installation.

Summary of content (4 pages)

PAGE 1
Wire Free Door Chime Kit Model No.: SC335T No wiring is required for this Wire Free Door Chime Kit. When the Push Button is pressed, it sends a wireless signal to the door chime that activates the chime. Since the operating range is up to 150ft (50metre approx. – in open field & at suitable condition), you can mount or take the door chime virtually anywhere in the home, workshop, office or garden.
PAGE 2
Melody Selection The melody selector is located inside the Push Button unit, a small switch on the top right corner of battery compartment marked with “S”. Press the switch once, the melody will change to play the next one on the list, there are total of 8 melodies for selection. 1. Westminster Chime 2. Ding-Dong Repeat 3. Telephone Ring 4. Circus Theme 5. Banjo on my knee 6. Twinkle - Twinkle 7. It’s a small world 8. Dog Barking Optional: Additional Push Button can be installed at the back door.
PAGE 3
friendly manner in accordance with the relevant legislation. 6. 7. Make sure that no naked flame sources, such as lighted candles, should be placed on the unit. The unit should not be exposed to dripping or splashing and no objects filled with liquids, such as vases, should be placed on the unit. 8. 9. CAUTION: Make sure batteries are installed correctly as per the internal markings. CAUTION: Replace only with the same or equivalent type of battery that is recommended by the manufacturer. 10.
PAGE 4
FCC & IC Compliance Statement This device complies with part 15 of the FCC rules and complies with RSS-210 of the IC rules. Operations are subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.