Digital Active Outdoor DVB-T/T2 Antenna Picture similar SRT ANT 45 User Manual Manuel d’utilisateur Bedienungsanleitung Istruzioni d’uso Manual de usuario Manual do Usuário Bruksanvisning Bruger Manual Käyttöohje Outdoor Antenna 5 V active antenna UHF & VHF Low noise amplifier Használati útmutató Návod k obsluze Používateľská príručka Instrukcja obsługi Korisnički priručnik Uputstvo za upotrebu Manual de utilizare Ръководство на потребителя 2-way mounting Waterproof UV resistant
Supplied by STRONG, Austria Represented by STRONG Ges.m.b.H. Franz-Josefs-Kai 1 1010 Vienna Austria Email: support_at@strong.
1 2 2 3 5 1.0 INTRODUCTION Thank you for purchasing the STRONG SRT ANT 45 DVB-T/T2 antenna. This antenna has been specially designed to receive digital terrestrial signals. It can be connected to any Digital Terrestrial Receiver (DVB-T/ T2), and is specially designed for outdoor use. The antenna housing is UV protected and weather-proof sealed. With the supplied multi-functional mounting material, you can install the antenna on a wall, on your balcony or on a pole outside the house.
PART 2 2.0 PACKAGE CONTENTS 1. 2. 3. 4. 5. 6. 7. Active DVB-T/T2 Outdoor Antenna. Multidirectional base (flexible). Wall mounting kit. Pole Mounting kit. Coaxial Cable. Power Injector. AC/DC adapter. Fig. 1 1 2 5 3 6 4 7 3.0 SAFETY NOTES Be careful working outside with overhead power lines to avoid electrocution Use only originally supplied accessories. Before you make any connections: disconnect your equipment from the 230 V main power to avoid electric shocks during installation.
Preparations 1. Check if the broadcast in your country is horizontally or vertically polarised. 2. Fix the antenna to the multi-directional base as shown in the pictures (the bracket is flexible and can be bent to the shape shown in Fig. 2) 3. Depending on how the signals are broadcasted (horizontally or vertically) you will have to mount your antenna in the horizontal or vertical position for best performance. 4. Your antenna needs 5 V power to work properly.
PART 2 7. Proceed to 5.0 “Antenna installation”. Fig. 4 3 1 1. Digital TV 2. STB 3. Active DVB-T/T2 Outdoor Antenna. 4. HDMI or SCART cable (optional) 5. Coaxial cable 6. Water-Drop Loop (recommended) 4 2 5 6 If your receiver does not support 5 V antenna power, then please follow the next steps: 4.2 To power the antenna with external power adapter 1. Switch OFF your receiver and disconnect it from the 230 V mains power. 2. Take the short coaxial (IEC Male to IEC Female) cable.
English Fig. 5 3 1 4 2 5 1. Digital TV 2. STB 3. Active DVB-T/T2 Outdoor Antenna. 4. HDMI or SCART cable (optional) 5. Coaxial cable 6. Water-Drop Loop (recommended) 7. Power injector 8. AC adapter (12 V) 9. AC mains outlet 6 7 8 9 5.0 INSTALLATION OF THE ANTENNA 1. Turn on your TV set and turn on your Digital Terrestrial Receiver. 2. Press the "MENU" button on the remote control of your Digital Terrestrial Receiver. Select the menu on your receiver that shows the signal level indicators.
PART 2 5.1 Installation on the wall 1. Take the multi directional base and hold it to the position on the wall (the bracket is flexible and can be bent according to your needs) 2. Mark the 4 holes with a pencil 3. Drill 4 holes with 5.8 mm diameter (make sure you are in a secured position and wear sufficient protective clothing while drilling) 4. Insert the 4 plastic plugs into the drilled holes 5. Hold the multi directional base on its position 6. Use the 4 screws to fix the plastic mount on the wall Fig.