Picture similar Digital Terrestrial HD Receiver SRT 8115 User manual Bedienungsanleitung Manuel d’Utilisateur Manuale Utente Manual del usuario Manual do Utilizador Felhasználói kézikönyv Instrukcja obsługi Ръководство на потребителя
Digital Audio Amplifier
PART 1 • English 26 Apr 2013 16:02 2 2 2 3 3 3 4 4 4 4 4 5 5 5 5 6 6 6 6 6 7 8 8 8 9 9 9 9 9 10 10 10 12 13 15 16 17 19 21 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change.
PART 1 • English 1.0 Introduction 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
packaging with its accessories. Failing to comply with such packaging procedures could damage the product and void your warranty. 1.3 Equipment Set-up We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: Refer to the user manual of your TV and antenna. Make sure that the HDMI cable and outdoor components are in a good condition. Use only a HDMI 1.3 cable or higher for maximum performance.
PART 1 • English 2.0 Your Receiver 2.1 DEFAULT PIN: 1234 2.2 Front Panel 1. 4 digits display Indicates current time in STANDBY mode Indicates current channel number in OPERATING mode 2. USB Connector for USB storage devices. 3. IR sensor Point your remote control towards this sensor. 4. Mode indicator RED indicates that the receiver is in STANDBY mode. GREEN indicates that the receiver is in OPERATING mode. Fig. 1 2.3 Rear Panel Fig. 2 1.
10. tu Menu Off: Decreases/increases the volume level. Menu On: Change settings for specific menus 11. OK Menu Off: Displays the current channel list Menu On: Activates the highlighted menu item. 12. RECORD Records the TV programme to the connected USB storage device 13. TIMESHIFT Activates the Timeshift function (Off/On) 14. 0~9 Enters a channel number in viewing mode or a value inside the respective menu 15. EPG Opens the EPG (Electronic Programme Guide) in TV mode 16.
PART 1 • English 3.4 Connecting to TV with RCA cable Fig. 4 TV sets without SCART or HDMI input(s) can be connected to the receiver using suitable RCA cables. Connect one end of the cable to the Audio L, R and VIDEO connectors on the back of the receiver. Connect the other end to the respective inputs on your TV set. 3.5 Connecting to a Digital Audio Amplifier with S/PDIF Fig.
PART 1 • English English Region: Select your region where this receiver is used. Subtitle: Select Normal to display subtitles per default, Select Hard of Hearing to show HoH subtitles per default. Select Off to hide subtitles per default.* Aspect Mode: Use this option to select the aspect ratio of your TV and the preferred conversion method.
PART 1 • English To turn your receiver ON or to Standby, use the q button on the remote control. Choose the desired channel with the pq buttons. Alternatively, you can digit the channel number with the 0~9 buttons on the remote control or press OK in viewing mode to display the channel list. The volume can be adjusted with the tu buttons. 6.0 Operation Your new receiver is equipped with several features to make watching TV a true pleasure. This paragraph describes these features.
PART 1 • English 6.3 Selection of audio language English Some channels support a choice of audio formats and/or languages. To select another audio stream, press AUDIO in viewing mode. A list with available audio streams will now be displayed. Use pq to select the desired stream and confirm with OK. The audio channel as stereo, mono, left and right can be selected with the tu buttons. 6.4 Teletext Your receiver includes a fully featured Teletext.
PART 1 • English Note: Availability of EPG data depends on broadcast. 6.8 Instant Recording Your new receiver allows you to make an instant recording of the programme you are watching. Simply press RECORD to start the recording. To enter the duration for the recording, press RECORD again. Use the 0~9 buttons to enter the recording time. At the begin of the recording a recording sign will be shown for a short while on the upper left corner of your TV screen. To stop the recording, press 3.
To lock or unlock a channel, press RED while in TV Channel List. The red on the top of the screen will move up to indicate that the Lock function is selected. Use pq to select the a channel and press OK to lock or unlock it. You are asked to input the PIN code. (DEFAULT PIN: 1234) Locked channels will be marked with the symbol. Locking/unlocking multiple channels in one session is possible. When all changes have been made, press EXIT twice. A confirmation banner will pop up.
PART 1 • English will now pop up at the right of the screen. Use tu pq to select characters and enter them with OK. When you have finished editing, press BLUE to enter the changes. When all changes have been made, press EXIT twice. Select Yes to save the changes or No to discard. Delete Press BLUE in Edit Channel to enable the Delete function. The Delete sign will move up to indicate that Delete is selected. Use pq to highlight a channel and press OK to mark it for deletion.
Use pq to select Channel Scan and press OK to enter. Use tu to toggle between available scan modes: By Channel and By Frequency. If By Channel is selected, use the cursor buttons to select Scan Band and Channel No. If By Frequency is selected, use the cursor buttons to select Frequency and Bandwidth. Highlight Search and press OK to start scanning. Newly found channels will be added to the channel list. 7.2.3 Antenna Power Use pq to select Installation, press OK or u to advance.
PART 1 • English manual selections 480i, 576i up to 1080p Please use a setting that matches your TV’s specifications. After a selection is made, you will be asked to confirm. Selection above 576i is only applicable on HDMI output. Aspect Mode: Use this option to select the aspect ratio of your TV and the preferred conversion method.
Wakeup Date: Use the 0~9 buttons to input the date for the timed event. Wakeup Time: Use the 0~9 buttons to input the start time. Duration: Use the 0~9 buttons to input the timer duration. When all settings are according to your wishes, use pq to move the highlight to Save and press OK to confirm. To quit the timer without saving your settings, move the highlight to Cancel. 7.3.5 Parental Lock This menu allows you to protect the installation menu and/or channels with a PIN code.
PART 1 • English Warning! By resetting your receiver to factory default, all your settings and stored channels will be permanently deleted. Please use this option with care. Use pq to select Load Factory Settings in the Tools menu and press OK. You are asked to input your PIN code. Input the correct PIN code using the 0~9 (DEFAULT PIN: 1234). A confirmation window is displayed. Select Yes to return to factory settings. Select No to cancel. Press EXIT to leave. 7.4.
PART 1 • English The Media menu consists of the following submenus: Media Player, HDD Information and DVR Setting. Use pq to highlight the menu of choice and press OK to enter. Press EXIT to quit. 7.6.1 Media Player This function allows playback of different kind of files from the connected USB storage device. In the Media menu, select Media Player and press OK to enter this menu. When entering the media player, the highlight is on the USB storage device.
PART 1 • English 6 7 2 INFO EXIT Image: 4 5 6 7 2 INFO 3 EXIT Press 6 to add all files of this directory/folder to the play list. Press 6 again to delete all files from the play list. Press 7 to open the Edit menu. This menu allows accessing the following functions by entering the number: rename 4, copy 5, delete 6, create folder 7. Press button 2 to open the sort window. You can sort by Name/Time/Size and Favourite. Press the INFO button to set repeat mode.
PART 1 • English English Warning! Formatting will permanently delete ALL data stored on the connected device. Please make a backup copy of all data you wish to keep before entering the HDD Format menu. STRONG cannot be held responsible for loss of data from USB devices used with this receiver. Press OK to proceed, select FAT or Cancel, or press EXIT to leave without formatting. Note: It is possible to use USB storage devices already formatted in NTFS. Press EXIT to leave this menu. 7.6.
PART 1 • English Problem Possible cause What to do LED indicator is not lit Mains lead unplugged Check mains plug No signal found Aerial is disconnected Aerial is damaged/misaligned Out of digital signal area Active antenna requires to switch ON antenna power/ external power Check aerial lead Check aerial Check with dealer Switch receiver’s Antenna Power ON/connect external power No picture or sound on TV or amplifier HDMI or SCART is not selected on your TV or amplifier or the unit is set to hig
PART 1 • English English 9.0 Technical Specifications Demodulator Demodulator: COFDM; 16 QAM/64 QAM, QPSK Transmission mode: 2 K - 8 K Video Decoder Profile level: MPEG-2 MP@ML, AVC/H264HP@L4.1, MPEG4 ASP supported Video resolutions: 480i / 480p / 576i / 576p / 720p / 1080i / 1080p / By Native TV / By source Decoding & Video out: PAL Aspect ratio: 4:3 Letterbox, 4:3 Pan & Scan, 16:9, Auto Audio Decoder Audio support: AAC/DD+*/AC3/PCM MPEG MusiCam Layer 2 Sampling rate: 32, 44.
PART 1 • English USB 2.0 port: 5 V/800 mA (max.) General Data Supply Voltage: 220 - 240 V AC (SMPS), 50/60 Hz Power Consumption: 4.40 W (typ.), 12.00 W (max) Power consumption in Standby: 0.80 W Operating Temperature: 0 ~ +40° C Storage Temperature: -30 ~ +80° C Operating Humidity Range: 10~85%, RH, Non-condensing Size (WxDxH) in mm: 188 x 135 x 44 Net-weight: 0.