Picture similar Digital High Definition Satellite Receiver SRT 7002 User Manual Bedienungsanleitung Manuel de l'utilisateur Manuale per l'uso Használati útmutató Руководство пользователя 03 Sep 2012 15:24
1 2 3 4 5 6 7
Table of Contents 05 Jul 2013 18:14 1.0 Instruction 2 1.1 Safety Instructions 2 1.2 Storage 2 1.3 Equipment Set-up 3 1.4 Accessories 3 1.5 Usage of external USB devices 3 2.0 Your Receiver 3 2.1 PIN code default: 0000 3 2.2 Front panel 3 2.3 Rear panel 4 2.4 Remote Control 4 2.5 Installing the Batteries 5 2.6 Using the Remote Control 6 3.0 Connections 6 3.1 Basic connection using a Scart cable 6 3.2 Basic connection using an HDMI cable 6 3.3 Connecting multiple fixed LNBs using a DiSEqC 1.
PART 1 • English 1.0 Instruction 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
English PART 1 • English its accessories. Failing to comply with such packaging procedures could damage the product and void your warranty. 1.3 Equipment Set-up We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: Refer to the user manual of your TV and your antenna. Make sure that the SCART/HDMI cable and outdoor components are in a good condition and the SCART/HDMI connections are well shielded and from good quality.
PART 1 • English 1. 2. 3. 4. 5. 6. Power button: To turn ON/OFF the main power supply Remote control sensor: Receives the signal from the remote control LED display: Shows channel number in operation and time in Standby Standby indicator: Shows power state of the receiver Green LED - receiver is turned on Red LED - receiver is in standby mode USB: For connection of external storage devices Channel up/down: To change channels without using the remote control 2.3 Rear panel 1. 2. 3. 4. 5. 6. 7. Fig.
10. EXIT Go back one step in the menu/cancellation of current process/exit from main menu to viewing mode 11. tu Decreasing/increasing the volume level in viewing mode/navigating through the menus/changing values of settings in a menu 12. pq Switches to the next/previous channel in viewing mode, switches to the next/previous page in channel list or moving the highlight up/ down in the menu. 13. OK Viewing mode: Displays the channel list. Menu: activation of the highlighted item 14.
PART 1 • English 1. 2. 3. Open the cover Install batteries Close the cover NOTE: The batteries should not be recharged, disassembled, electrically short-circuited, be mixed or used with other types of batteries. 2.6 Using the Remote Control Fig. 5 To use the remote control, point it towards the front of the digital receiver. The remote control has a range of up to 7 metres from the receiver, if properly aligned towards the IR eye on the front panel.
default, the First Installation menu will appear on your TV screen. Use the tu buttons to select the OSD Language of your preference and press OK to confirm. An Info page will be displayed. Read the info guide and press the INFO button to proceed to the next Installation step. You can open and close the info page again by using the INFO button. Note: If German is selected as language, German preset channels from ASTRA 19.2E will be installed.
PART 1 • English 6.0 Operation In viewing mode, several features are available to make watching TV a true pleasure. This paragraph describes these features. Please also read chapter 7 to get familiar with the menu of your new receiver. 6.1 Changing channels There are different ways to change channels with your new receiver. Via direct access Via the channel list Via the pq buttons Via the RECALL button 6.1.
You can change the on-screen duration of the info banner in the Option menu. Please refer to section 7.5 for more details. *Programme information is displayed when available. Availability depends on broadcast. 6.3 Selection of audio language Some channels support a choice of different audio formats and/or languages. To select another audio stream, press AUDIO in viewing mode. A list with available audio streams will now be displayed. Use pq to select a stream and confirm with OK.
PART 1 • English 6.9 Favourite channels Use the FAVOURITE button to access your favourite channels and to toggle between available favourite groups. Please refer to section 7.1.1 for details on how to create favourite lists. 6.10 Changing between DTV/VCR contents The receiver has the possibility to loop through the signal from the VCR SCART input to the TV SCART. This allows you to watch content from the connected DVD or VCR recorder via the receiver.
3. English PART 1 • English Now in viewing mode you can select channels from the chosen favourite group only by pressing pq. If you want to change to the main channel list, press OK in viewing mode and then press GOTO and select All satellites. Delete a TV or radio programme 1. Select the programme you want to delete and press the BLUE button. A message will appear. Press OK to delete the programme or EXIT to cancel. 2. Repeat the previous step to delete more programmes. Skip TV or radio programme 1.
PART 1 • English 3. To store the changes and exit the menu, press EXIT. 7.1.2 EPG (Electronic Programme Guide) Please refer to section 6.8 above. 7.1.3 Sort Here you can sort your channels in the following orders: Default Sort the channels in the original order By Service Name Sort the channels in alphabetical order (A-Z) By Frequency Sort the channels in frequency order (Low-High) By Encrypt Sort the channels from free to scrambled 7.2 Picture Press MENU, then select Picture.
English PART 1 • English Video Output This setting is only relevant when the receiver is connected to the TV set via Scart. Select RGB for the best picture quality or CVBS if your TV doesn’t support RGB. Loop Through (VCR to TV Scart) This option is only relevant if you have a device (video-/DVD-recorder) connected to the VCR scart connector of your receiver. Its signal will be looped through to the TV scart output of your receiver. Use this option to set the preferred loop-through mode.
PART 1 • English Move Continue: press tu for moving West/East. It will keep moving as long as the button is hold pressed. By pressing once it will move in 1°step. Move Step(1): press tu for moving West/East in 0.3° step. Store Position: to store the current motor position for selected satellite. Goto Reference: to go to the reference 0° position. DiSEqC1.3: Select DiSEqC1.3 with the tu buttons. Press GREEN to setup your location coordinates.
and press BLUE for Scan. A window with scanning settings will be displayed. After configuring the settings like explained in Single Satellite Scan above, press OK or BLUE again to start Multi-Scan on all selected satellites. 7.3.1.4 Scanning by transponder (Manual Scan) Press GOTO for displaying the transponder list of the highlighted satellite. By pressing GOTO again you switch back to the satellites list. Single Transponder Scan: Use the pq buttons to highlight the transponder you want to scan.
PART 1 • English Edit transponder: Press GREEN to edit the highlighted transponder. In the pop-up banner, change the transponder´s data by using the navigation and numeric buttons. Confirm changes with OK or cancel with EXIT. Delete transponder: Press YELLOW to delete the highlighted transponder. Press OK to confirm or EXIT to cancel. 7.3.2 DB Management This menu allows you to save and reload the channel data base of your receiver from/to a USB-device.
right channel number by selecting the first letters of the channel´s name in the pop up window. When you have entered all parameters, press OK to store your booking. Edit: Press the GREEN button to edit an existing booking. Delete: Press the BLUE button to delete a booking from the list. Press OK to confirm deleting or EXIT to cancel. Note: You can set timers for programmes directly from the EPG. Please refer to section 6.8 for more details. 7.5 Option Press MENU and select Option.
PART 1 • English Warning: A factory reset will permanently delete all your personal settings, timers and stored channels. Please consider this before you perform a factory reset. Information Shows model, software and hardware information. Recall List Enable or disable the Recall list function, which supports multi-recall-channel switching. If the status is set ON then a list of all previously selected channels will be displayed for new selection by pressing the RECALL button.
English PART 1 • English Auto Standby Auto standby is a new, power saving feature that helps you reduce power consumption. It will switch off the receiver when no command is given for the defined period of time. It is set per default to 180 minutes. With the tu buttons you can select between different time intervals or Off for disabling the feature. In the 0000 mode you can enter the auto standby time with the 0~9 buttons.
PART 1 • English REPEAT: Press once for single file repeat, twice to repeat all files or three times for random playing. The symbol for selected repeat mode will appear at the top of the screen. Press once again to return to the common play mode. RECALL: Goes to the parent folder. EXIT: To get back to the Multimedia menu. Press EXIT once more if you want to leave the Multimedia menu. TIP: Playback of music will continue as long as the Multimedia menu is active.
again or EXIT. Use the GOTO button and enter the time moment you want to jump to with the 0~9 buttons, then press OK to confirm. With the 5 6 buttons you can rewind or forward playback in x2, x4, x8, x16 and x32 speed. When it has fast rewinded to the beginning, playback of the current file will be resumed. When it has fast forwarded to the end, playback of the next file starts. With the 7 8 buttons you can jump to the previous/next video file.
PART 1 • English 8.0 Troubleshooting There may be various reasons for abnormal operation of the receiver. Please check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact your local Service line or STRONG dealer. Alternatively you can send a support mail via our website: www.strong.tv. NEVER open or disassemble your receiver. This may cause a dangerous situation and will void the warranty.
Problem The external USB HDD does not start. The receiver switches to standby automatically. English PART 1 • English Possible cause Power consumption is too high. What to do Connect an extra power supply adapter to your USB HDD device. Set the power down time or Auto Standby function is activated and has reached the set disable it in the System Auto Standby menu . time (default 3h). 9.
PART 1 • English Multimedia Video playback: Supported in various formats (MPG, MPEG, TS, VOB, MP4, AVI…)* Audio playback: MP3, WMA formats Picture view: JPG, BMP formats *STRONG cannot guarantee the playback of video files although extensions are listed here, as it depends on codec used, data bit rate and resolution. Connectors SAT IN SAT OUT HDMI (V/A -Output) Type A -Version: 1.
