Picture similar Digital Satellite Receiver with Digital Recorder SRT 6365 PDR User Manual
PART 1 • English 1.0 INTRODUCTION 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Features & Accessories 2.0 YOUR RECEIVER 2.1 Front Panel 2.2 Rear Panel 2.3 Remote Control Unit 3.0 CONNECTIONS 3.1 Connecting to TV & VCR 3.2 Connecting to Digital Audio Amplifier 3.3 Connecting to Satellite Dish 3.4 Connecting to computer via serial cable for downloading software 4.0 STARTING UP FOR THE FIRST TIME 4.1 Language Selection 4.2 Select connection type 4.3 Select Satellite 5.0 MAIN MENU 5.
PART 1 • English 1.0 INTRODUCTION 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots.
PART 1 • English We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: n Refer to the user manual of your TV and your antenna. n Make sure that the SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver. The following symbols will serve as follow. WARNING: Indicates warning information.
PART 1 • English Parental lock function for menu and selectable per channel Edit functions for TV or Radio programme name and satellite name n Future-proof: Software update via satellite (OTA) n Signal bars for satellite and digital transponders n Automatic, network and manual channel scan options n Power on with last viewed or preferred channel n 3 Games (Boxman, Tetris, Snake) n User-friendly remote control with coloured function buttons n Separate power switch n Supports DiSEqC 1.0, DiSEqC 1.
PART 1 • English 2.0 YOUR RECEIVER Figure 1 Power On/Standby button Increase/decrease volume level Channel Up/Down buttons Displays Main menu Confirm selection Start record of current channel RED light indicates that the receiver is in STAND-BY mode. GREEN light indicates that the receiver is in AWAKE mode. 8. 4 digits display In STAND-BY mode current time is indicated. In AWAKE mode is current channel number or current time (as selected in system set-up) indicated. 9.
PART 1 • English 6. VCR SCART Connector Use this connector to connect your receiver to your video or DVD recorder using a SCART cable. Video and Audio signals of your video or DVD recorder will now be looped through your receiver to your TV set. 7. S/PDIF Digital audio output Use this optical output to connect your receiver to the input of your digital audio amplifier. 8. RS-232 Serial Port This serial port can be used to connect your PC to your receiver in order to download new software versions to it.
TEXT SUB RECALL TV/RADIO INFO VOL +/PAGE +/0~9 PDR EPG Shows Teletext page, if available. If more then one Teletext language available then shows the list of Teletext languages the current channel supports. Show the list of subtitled languages the current channel supports. Switches back to previous channel. Switch between TV and RADIO mode. Shows information of the current channel or playback Use to increase or decrease the receiver volume level.
PART 1 • English 3. Connect the VCR SCART connector of the receiver to the SCART-IN connector on your video or DVD- Recorder Optional: Connect a terrestrial antenna with an UHF coaxial lead or antenna cable to the ANT IN connector at the back of the receiver. n Connect a coaxial cable to the TO TV connector at the back of the receiver. Connect the other end of this coaxial cable to the ANT IN connector of your VCR.
requested satellites and connect the LNB’s with coaxial cables to the input connectors of the DiSEqC 1.0 switch. Connect the output connector of the DiSEqC 1.0 switch to the SAT IN of TUNER 1 connector at the back of your receiver. Connect one end of LOOP cable to the SAT OUT of TUNER 1 and another end of LOOP cable to the SAT IN of TUNER 2. Use connection type LOOP THROUGH. NOTE: You can make duplicated installation of 2 or more satellites.
PART 1 • English 4.3 Select Satellite The Installation Wizard is preconfigured for easy installation of Astra 1 (19.2E) or Hotbird (13E). For these satellites LNB configuration is predefined as Universal LNB connected to the receiver via DiSEqC 1.0 switch input 1. If your dish is aimed to Astra 1 (19.2E) or Hotbird (13E) then select corresponding satellite from the list (future steps of installation are described in 4.3.1).
PART 1 • English 5.0 MAIN MENU English All the important settings and features of your receiver can be operated through Main Menu. It consists of following sub-menus: “Channel Organiser”, “Installation”, “Timer”, “Games”, “Common Interface” and “Recorder”. If in TV mode, press the MENU button to open the main menu. 5.
PART 1 • English 5.1.3 Edit Channels In this menu you can edit channel name, lock and delete channels. Edit Press RED button to edit name of the channel. On screen will appear keyboard. To delete current name select Backspace (t) symbol and press OK. To enter new name use tupq and OK buttons. Press RED button to save new name or press GREEN button to discard changes. Channel name will be changed in all channel lists. Lock Lock function can be used in order to block access to some channels.
PART 1 • English This item value depends from the mode of the Dish. If mode of selected dish is “Fixed” then this item is not selectable If mode of selected dish is “DiSEqC 1.2” then value can be “Not stored” (in case dish position for selected satellite was not stored”) or in range from 1 to 64 if position has been stored. Select item and press OK to setup Positioner. For more information about Positioner setup see chapter 5.2.1.1. If mode of selected dish is “GOTO X” then value is “GOTO X”.
PART 1 • English To setup single channel: Press GREEN (PID) button on the remote control.
PART 1 • English 5.2.2 Dish set-up In this menu you can setup parameters of your dish(es). Dish number: Use tu buttons to select number of the dish. This number used in Channel setup menu to create a link between satellite and corresponded dish configuration. Connection type: Use tu buttons to select connection type. It is advisable to not change this value in case you have installed channels. Before change the value please careful read chapter 3.3 of this manual.
PART 1 • English To save changes press the YELLOW (Save) or BLUE (Save & Exit) button. 5.2.4 GOTO X set-up In this menu you should set your geographical location, if your use positioner and it supports GOTO X. Use pq buttons to navigate in the menu. Use Numeric buttons to enter values. Use tu buttons to select an option. To save changes you have made press YELLOW (Save) or BLUE (Save&Exit) button. 5.2.
PART 1 • English Software update Select this option in order to update your receiver with the latest software version. Software update service is available from satellites ASTRA 1C, 1E, 1F at 19E and HOT BIRD 1, 2, 3, 4 at 13E.
PART 1 • English Action: Cycle: Start Date/Day of Week: Start Time: Duration: Channel name: You can select between “PDR Record” (recording on HDD); “Power On” (receiver powers on at the designated date and time); “Duration” (receiver switches on, at the designated date and time, displays the channel and then switches off after a designated duration) and “Power Off” (receiver switch to Standby). at the designated date and time.
5.5.1 Dual Descramble With this function you can configure the settings of scrambling capacity from smart card and Conditional Access Module. Some smart cards and CAM’s allow to open more then only one scrambled channel from same transponder. Please, ask your dealer for details and possibilities.
PART 1 • English 6.1.2 MP3 Player The MP3 view of the Records Organiser is divided into two separate parts. The folder and file view on the left side and the MP3 Player on the right side of the screen. Use the tupq cursor buttons to navigate. Press OK to open a folder or add a file to the play list, press PDR to switch between PDR, MP3 or JPG mode. Press EXIT to exit the menu. Use the pq buttons to navigate between records and tu buttons to change between list of records and play list.
PART 1 • English Enable or disable instant recording and HDD power save features. HDD power save feature allows you to save energy. The HDD power will be turned off after defined time interval of HDD is not in use. For example you define HDD power save is set to 10 minutes. This means that HDD power will be turned off after 10 minutes from the moment of last use of the HDD.
PART 1 • English 7.3 Channel list To open the current channel list press the OK button in TV mode. Use pqtu buttons to select channel and press OK to switch to this channel. For full screen TV mode press OK once more. To change satellite press SAT button and select satellite from the list. For displaying favourite channel list press FAV button and select favourite list. To exit from favourite mode press TV/RADIO button. 7.3.
one bandwidth, i.e. if you are recording channel from ASTRA 19.2E and channel is from transponder in Horizontal polarization High band (frequency above 11700 MHz) – the channel list will displays the channels located on transponders with Horizontal polarization High band on ASTRA 19.2 satellite. Recording of scrambled channels: there is possible limitation to record one scrambled channel and watch another one.
PART 1 • English 8.4 Playback There are two ways to access to your records: n Press PDR button on remote control once. n Press MENU, select Recorder, select Records Organiser NOTE: If you have enabled HDD power save and did not use HDD (did not playback or record) for a time set in HDD power save then appearing of the record list may take a while due to receiver need to re-activate HDD. Select a record you wish to playback and press OK button on remote control.
8.4.7 Place a bookmark This function allows you to place a bookmark at the most interesting moments of a record. During playback press INFO button. The playback information banner will appear on screen. Use tu buttons to scroll in the record to the point where you want to place a bookmark and press & button. You will see a red dot appearing on the playback progress indicator. You can place up to 32 bookmarks in one record. 8.4.
PART 1 • English A.1 TROUBLESHOOTING There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact the dealer. Don’t open the receiver cover. This may cause a dangerous situation. Symptom Cause Remedy The LED display on front panel does not light up. The power cord is not plugged in. Check that the power cord is plugged in to the wall outlet.
PART 1 • English Tuner Front-End: Input Frequency Range: RF Input Level: LNB Power: DiSEqC Versions: DVB-S 950 ~ 2150 MHz -25 ~ -65 dBm 13.5/18 V DC (± 5%), Max. 400 mA, Overload protected 1.0, 1.1 & 1.2 and GOTO X System and Memory CPU: Flash Memory: DDR SRAM: HDD: STi5100 @ 243MHz 4 MBytes 64 MBytes 160 GBytes UHF Modulator Standards: Channel: NTSC, PAL BG/I/DK 21 ~ 69 selectable via OSD English Audio Decoder ISO/IEC 11172 LAYER I&II and MP3 Sampling rate: 32, 44.
PART 1 • English A.3 TYPICAL INSTALLATIONS AND CONFIGURATIONS Single Universal LNB on fixed dish aligned to ASTRA 19.2E Channel setup menu settings Satellite: ASTRA 19.2E Dish number: 1 Dish Setup menu settings Dish number: 1 Connection: Loop through LNB type: UNIVERSAL Switch type: None Dish mode: Fixed Mono block Universal LNB on fixed dish aligned for reception of ASTRA 19.2E and HOT BIRD satellites Channel setup menu settings Satellite: ASTRA 19.
PART 1 • English Channel setup menu settings Satellite: ASTRA 19.2E Dish number: 1 Dish Setup menu settings Dish number: 1 Connection: Tuner 1&2 LNB type: UNIVERSAL Switch type: DiSEqC 1.0 DiSEqC input: 1 Dish mode: Fixed Channel setup menu settings Satellite: HOT BIRD Dish number: 2 Dish Setup menu settings Dish number: 2 Connection: Tuner 1&2 LNB type: UNIVERSAL Switch type: DiSEqC 1.0 DiSEqC input: 2 Dish mode: Fixed Single Universal LNB on dish aligned to ASTRA 19.
Environmental Issues ENVIRONMENTAL ISSUES STRONG is committed to reducing the impact of its products on the environment. To maximise the benefits of our design enhancements, your co-operation is required. Electronic product recycling Do not dispose of this product with your domestic rubbish. At the end of its useful life, this product contains materials which when processed correctly can be recovered and recycled.
