Picture similar Digital Terrestrial Receiver SRT 56 User manual Bedienungsanleitung Manuel d’Utilisateur Manuale Utente Manual del usuario Priručnik za upotrebu Návod k obsluze
PART 1 • English 1.0 Instruction 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories 1.5 Usage of external USB devices 2 2 3 3 4 4 2.0 Connection 2.1 Default Pin-Code: 0000 5 5 3.0 Your Receiver 3.1 Remote Control 5 5 4.0 First Time Installation 6 6 6 8 9 11 12 6.0 OPERATION 6.1 Changing Channels 6.2 Accessing the Electronic Program Guide (EPG) 6.3 Accessing the favourite channels 15 15 15 15 A.1 TroubleShooting 16 A.
PART 1 • English 1.0 Instruction 1.1 Safety Instructions This SCART Receiver has been manufactured to satisfy international safety standards. Please read the following recommended safety precautions carefully. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons.
GENERAL PRECAUTIONS - SAFETY PRECAUTIONS Lightning - If a lightning storm occurs while using a specified AC adapter, remove it from the wall outlet immediately. To avoid damage from unexpected power surges, always unplug the AC adapter from the power outlet and disconnect it from the receiver when the receiver is not in use. Overloading - Never overload wall outlets, extension cords, power strips, or other power connection points with too many plugs.
PART 1 • English of the antenna are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver. The following symbols will serve as follow. Warning Indicates warning information. Tips Indicates any other additional important or helpful information. MENU Represents a button on the remote control. (Bold Character) Represents a menu item within a window. (Italic Character) Move to 1.
PART 1 • English Connecting to TV, Terrestrial Antenna, IR Eye and Main Power Fig. 1 To receive the broadcast signal, the terrestrial antenna cable should be connected to the ANT IN connector at the receiver. Then connect the IR connector into the receiver and make sure it is properly connected to the IR sensor input. Afterwards you can plug the power adapter to the main power source (100 ~ 240 V, 50/60 Hz Auto detecting).
PART 1 • English 13. EPG Shows the EPG (Electronic Program Guide) in TV mode 14. ● Records the TV program to the USB-storage device Activates the timeshift function 15. TIMESHIFT 16. tt / uu Fast rewind / Fast forward Shows Teletext on OSD (On Screen Display) 17. TTX 18. TV/RADIO Toggles between TV and RADIO mode Shows list of the current audio channel /language 19. AUDIO Only used to go to desired position in Record/Playback mode 20. GOTO 21. COLOURED BUTTONS For Multimedia and Teletext functions Fig.
PART 1 • English Use this menu to favour, lock, skip, delete and rename channel list. Press numeric button [1] to enter edit menu. With the pq buttons highlight a channel and press OK to select or press numeric button [0] to select all channels. Selected channels will get marked. This way of selection can be executed for each of the edit functions. Favor: To add selected channel or all channels to a favourite group, press the [1] button. Use the pq to select a desired group and press OK.
PART 1 • English 5.1.2 Radio Channel list Basically, the operation of Radio Channel List is the same as in TV Channel List only difference is that in Radio Channel List there is no video information, so it will always display the radio logo at the right preview screen. 5.1.3 Delete Favourites and Groups Use this menu to delete all favourite channels. Select Delete Favourites And Groups with the pq and press OK, with tu select Yes in the confirmation window and press OK to delete or select No to cancel.
PART 1 • English 5.2.3 Antenna Setting English 1. Press MENU to enter main menu. 2. Use the pq buttons to select Installation, press OK to enter the menu. 3. With the pq buttons select Antenna setting and press OK to enter. 4. Press the tu buttons to change setting. If On is selected, the receiver will provide 5 V antenna power (for active antennas). 5. Press EXIT button to exit. 5.2.
PART 1 • English Time Display: This menu allow to control whether the time is displayed on screen or not. The options are: Off/On. 5.3.4 Timer Setting In this menu you can set a programme timer or sleep timer. Programme timer Timer Number: You can set 8 timers Timer Mode: Off/Once/Daily/Weekly/Monthly Timer Service: TV Service/Radio Service Wake-up Channel: You can select a desired channel as wake-up channel. Month/Date/Day: Press pq buttons to select your desired month, date and day.
PART 1 • English This option allows you to enable or disable Auto Standby. The default setting for Auto Standby is ON. The receiver will switch to standby automatically when it doesnt receive commands from the remote control for three hours. To avoid the automatic switch off, set Auto Standby to OFF . 5.4 Tools Press MENU button to enter main menu. Select “Tools” and press OK button to enter tools menu. 1. Press pq buttons to highlight the desired menu and press OK button to enter. 2.
PART 1 • English 5.4.4 Software Upgrade 1. Enter “Tools” menu, select “Software Upgrade” and press OK button, Software Upgrade menu is shown. 2. Press pq buttons to select “Upgrade by Storage” item and press OK button, you are asked to input password. 3. Input the correct password (the default password is 0000), Software Upgrade submenu is opened. Then select the correct software file and press OK to start. Message will be displayed to confirm update process, select “Yes” to confirm or “No” to cancel.
PART 1 • English English 2. Press pq buttons to select a desired recording and press OK or BLUE (u) button to playback the desired files. 3. Press EXIT button to exit. During the playback, it is possible to perform the following actions: Press YELLOW (II) button to pause the playback. buttons for fast forward or fast rewind during playback Press the Press GREEN (Iu) button once to perform slow motion, every further press will change the slow motion speed (1/2, 1/4, 1/8). 5.5.
PART 1 • English Stop Time Shift If you want to stop Time Shift press EXIT or tu buttons, then a confirmation window appears. Select Yes to stop Timeshift or select No to continue Timeshift. Record There are 3 different ways to record programmes: Instant recording, recording from EPG and recording via Timer Instant record In viewing mode press the ● button to instantly start a record on the current channel. Press the RED (■) button to stop recording.
6.0 OPERATION 6.1 Changing Channels There are 4 ways of channel selection - stepping through the channel list, selection by number, from the on-screen channel list, and using the electronic programme guide (EPG). 1. Stepping through the channel list To move through the channel list, press the pq buttons on the remote control. 2. Selected by number Enter the channel number directly by pressing numeric buttons, and press the OK button to select desired channel. 3.
PART 1 • English A.1 TroubleShooting There may be various reasons for abnormal operation of the receiver. Please check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact your local Service line or STRONG dealer. Alternatively you can send a support mail via our website: www. strong.tv. NEVER open or disassemble your receiver. This may cause a dangerous situation and will void the warranty.
PART 1 • English Possible cause Power consumption is too high. What to do Connect an extra power supply adapter to your USB HDD device. A.2 Specifications Demodulator Demodulator: 16-QAM/64-QAM, QPSK Transmission mode: 2 K, 8 K Video Decoder Profile level: MPEG-2 MP@ML Video resolution: 720 x 576 pixels (PAL), 720 x 480 (NTSC) Decoding & Video Out: PAL & NTSC Aspect ratio: 4:3 Letterbox, 4:3 Pan & Scan, 16:9 Audio Decoder MPEG MusiCam Layer II Sampling rate: 32, 44.
PART 1 • English General Data Power source: 100 – 240 V AC, 50/60 Hz (Auto detecting) Power Consumption: 3.