User's Manual Part 3

ManualsBrandsStrategic Technologies ManualsElectronicsSTILOCK

PRU Installation - Classic

Use this method if you are going to use the standard installation technique.

1. Plug in the PRU+: Plug one end of the AC Adapter into a 110 Volt AC Outlet and the other

end into the PRU+. The PRU+ will turn on, displaying the title screen. It will then display the

date and time screen. The power and charge LED will be lit. The charge LED will go out when

the unit is fully charged.

2. Clear Stored Events: Press and hold the PRU+ button on the LOCK until the PRU+

prompts “Please Wait....”. When the display prompts “B=Function Mode” press B button once.

The display will prompt “B=Clear Events”. Press B to clear all stored events. The display will

read “Events cleared”.

3. Test for RF Signal Strength: Press “A” button twice. When the display prompts “B=Test

Mode”, press the “B” button to enter Test Mode. Look at the top line marked “RFStr”. The

display will have a value on the top line that indicates the

signal strength of the last transmission of the PID

displayed. The

value is a

representation

of the distance

the PID is

located away

from the PRU+.

To reduce the

range the PRU+

will monitor the

participant set the RSSI setting in Extended Special Function Mode to this value minus 15%

(approx 30 points). Note: setting this value higher will reduce the size of the area of

confinement..

PID Installation

5. Install the Battery: Remove the PID , baseplate, one strap, one locking bar, one locking pin

and the battery from the case. Simply place the battery into the PID battery well so that the

alignment mark on the battery lines up with the alignment mark on the PID. Rotate the battery

counterclockwise until the tabs on the battery slide under the two lock down posts. (See Figure

3 : installing the battery in the PID).

Figure 3: Installing the battery in the PID

6. Size the Strap: Attach the wide end of the strap to the PID baseplate. With the baseplate on

the outside of the leg, wrap the strap around the participants leg, just above the ankle. Size the

Summary of content (16 pages)

PAGE 1
PRU Installation - Classic Use this method if you are going to use the standard installation technique. 1. Plug in the PRU+: Plug one end of the AC Adapter into a 110 Volt AC Outlet and the other end into the PRU+. The PRU+ will turn on, displaying the title screen. It will then display the date and time screen. The power and charge LED will be lit. The charge LED will go out when the unit is fully charged. 2.
PAGE 2
strap so that it fits comfortably around the participant’s leg. Cut off any access strap that is above the two hole positions that will fit into the other side of the strap (See Figure 4 : Strap installation) Figure 4 : Strap Installation 7. Install Strap and PID: Replace the baseplate and strap around the leg, and attach the narrow end that has been cut to length to the baseplate. Push the PID onto the baseplate at the strap end. The PID is now hinged to the baseplate.
PAGE 3
9. Check Strap Tightness: Check the strap tightness on the side opposite the PID. There should not be a space of more than ½ inch or 1.4 centimetres between the strap and the skin. Installation Completion 10. Test the PID Signal: Watch the PRU+ in test mode, to ensure that the signal from the PID is being received. The PID code number will be displayed and the PRU+ will beep to indicate it has received the signal from the assigned PID.
PAGE 4
1. Connect AC Power & Telephone: Connect AC Power to the PRU+ by plugging the AC adapter into a wall outlet. Connect the telephone into the telephone outlet. The PRU+ should immediately start to call into the central computer. 2. Wait for “Call Successful”: When the PRU+ indicates “Call Successful” the PRU+ has transferred all of the stored information. If the PRU+ does not indicate “Call Successful” the PRU+ needs to call into the CC again.
PAGE 5
STRATEGIC Technologies Inc. Domestic Violence Domestic Violence Unfortunately, issuing restraining orders does not assure safety to domestic violence victims. Courts and law enforcement agencies enforcing stalking and domestic violence restraining orders require assistance which the Platinum Plus 400 Series can supply. The offender, wearing a transmitter, can continue to function in the community while complying to the restraining order.
PAGE 6
STRATEGIC Technologies Inc. Domestic Violence Installation Domestic Violence Installation Victims Installation Pre-Installation A. If your equipment is monitored by our Monitoring Center:- Fax the Enrollment Form to the Monitoring Center, giving as much time as possible (½ hour minimum) before the unit is to be hooked up inside the victims home. The Monitoring Center must be notified before the unit calls in.
PAGE 7
STRATEGIC Technologies Inc. Domestic Violence Installation Figure 3: Installing the battery in the PID 6. Check PID Transmission: Press A twice then hit B to go into Test Mode. Hold the PID and watch the PRU+ Test Mode Screen for a transmission from the PID. When the signal is received it should indicate strap sever symbol. The PRU+ should also beep to indicate the PID has the correct code.
PAGE 8
STRATEGIC Technologies Inc. Domestic Violence Installation De-Installation / Removal A. If your equipment is monitored by our Monitoring Center:- Fax the Inactivation Form to the Monitoring Center on the same day that the unit is to be removed from the offender’s residence. B. If you monitor your own equipment:- Assure the offender ‘s sentence ends on the same day that the unit is removed from the victim’s residence. 1. Disconnect the PRU+: Disconnect the telephone cord from the PRU+ and wall jack.
PAGE 9
STRATEGIC Technologies Inc. Special Function Mode Special Function Mode The PRU+'s Special Function Mode allows the installer to change various configuration settings, clear the stored events, and enter a test / diagnostic mode. To enter the Special Function Mode, you use the LOCK. Simply press the PRU+ button on the LOCK, while holding the LOCK within three feet (1 metre) of the PRU+. The front panel display will show the message "Please Wait....
PAGE 10
STRATEGIC Technologies Inc. Extended Special Function Mode Extended Special Function Mode Extended Special Function Mode is used to change the internal settings inside the PRU+. The ability to change the internal settings gives the PRU+ great flexibility. The installer can now change important settings depending upon their needs. Extended Special Function Mode can be accessed by moving to the screen “B=Exit” as shown on pages 36 and 37.
PAGE 11
STRATEGIC Technologies Inc. Extended Special Function Mode B=Set A=Next RSSI Function 100 This screen enables the installer to limit the range the PRU+ will detect the presence of the PID. If transmissions are received from the PID with a signal strength less than the value set the transmission will be ignored. The value may be set between 0 - 255. A value of 0 indicates all transmissions will be valid. To set the value press B and a cursor will appear under the first digit of the setting.
PAGE 12
STRATEGIC Technologies Inc. Extended Special Function Mode This screen allows the installer to change the format of the date displayed by the unit during normal operation. Pressing the "B" button repeatedly will cycle through the available options: YMD (year/month/day), MDY (month/day/year), or DMY (day/month/year). Press the "A" button to move to the next screen.
PAGE 13
STRATEGIC Technologies Inc. Extended Special Function Mode B=EXIT A=Next Function This final screen allows the installer to exit extended special function mode. Pressing the "A" button returns the installer to the very first screen (“A=Turn PRU+ Off / B=Function Mode”). Pressing the "B" button causes the PRU+ to exit Special Function Mode and resume normal mode. All settings are automatically saved at the time they are entered.
PAGE 14
STRATEGIC Technologies Inc. Test Mode Test Mode Test Mode which is accessed from the Special Function Mode screens is useful for many diagnostic tests. Selecting test mode causes the screen shown below to be displayed. Figure 1 : Test Mode Display The top line of the display is the signal strength of the last transmission received from the PID along with the channel received. The left half of the bottom line provides PRU+ status information.
PAGE 15
STRATEGIC Technologies Inc. Test Mode The symbols to the right of the code number provide the following information: PID Case Open - indicates the last received transmission showed a case open alarm. Strap Sever - indicates the last received transmission showed a strap cut alarm.
PAGE 16
STRATEGIC Technologies Inc.