User's Instructions



Stratasys Ltd.

1 Holtzman St., Science Park, P.O. Box 2496, Rehovot 7670401, Israel T:+972-74-745-4000 F:+972-74-745-4001 www.stratasys.com

1



User’s instructions to use the

RFID reader system for Material Cabinet ASY-18130.

1‐“ContainsFCCID:YH6‐DUPCAB1“.

2‐FCCStatement

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,pursuantto

part15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmful

interferenceinaresidentialinstallation.This

equipmentgenerates,usesandcanradiateradiofrequency

energyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferenceto

radiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticular

installation.Ifthisequipmentdoescauseharmfulinterferencetoradio

ortelevisionreception,whichcanbe

determinedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferenceby

oneormoreofthefollowingmeasures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

StratasysLtd.isnotresponsibleforanyradioorcommunicationinterferencecausedbyusingotherthan

specifiedorrecommendedcablesandbatteryorbyunauthorizedchangesormodificationstothisequipment.

Changesormodificationsnotexpresslyapprovedbythemanufacturercouldvoidtheuser’sauthorityto

operatetheequipment.

Thisdevice

complieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:

1.Thisdevicemaynotcauseharmfulinterference,and

2.Thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesired

operation.

3‐Useconditions

TheRFIDreaderistobeincorporatedintheMaterialcabinet(Host)bytheGranteeandisnotforsaletoany

otherthirdparties.

4‐Limitedmoduleprocedures

4.1‐themodulartransmitterdoesn'thaveitsownRFshielding

PAGE 1
User’s instructions to use the RFID reader system for Material Cabinet ASY-18130. 1‐“Contains FCC ID: YH6‐ DUPCAB1“. 2‐ FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
4.2‐ The module transmitter has RFID transmission protocols 4.3‐ The RFID unit voltage is 5V (produced from the main 24VDC). 4.4‐ The module transmitter has a Loop coil antenna mfr. Stratasys model. BRD‐03012 4.5‐ The modular transmitter has been tested inside an auxiliary device therefore it is matching module limited approval 4.6‐ The modular transmitter is labeled with FCC ID and as it is not visible to the user, there is an exterior label including "Contains FCC ID: YH6‐ DUPCAB1" 4.
PAGE 3
attached to the resin material container. Its intended use is to identify the type of resin. 10‐ The modular transmitter is ONLY FCC authorized for the rules as listed on the Grant. If other FCC rules apply to the host and are not covered by the modular grant, these are the host manufacturer responsibility. 11‐ Operation The PC sends command states to the MSC2 board to identify the transponders (check for cartridge presence) – than the reader creates electromagnetic field emitting thru the antenna.