User's Manual

USER MANUAL

Wireless nunchuk is applicable to Wii Remote Control use, the original Wii Remote Control and

Nunchuk were wired connections to connect them, Due to wired connection the gaming distance

was limited, This product is away from way of use the limit as the improvement. the Nunchuk

transmitting end distance may amount to 5-6 meter. Transmitter has searching key ( comb key)

and connection with electricity show (Status LED) Build in Transmitter on Wii Nunchuk with

battery that will automatically go to sleep mode ,at this time press comb key then it will search all

channels to find the ID on the receiver (to register it), the LED will flicker with 2HZ rate, if in 10

seconds it does not connect with the receiver then it will automatically enter the dormant

linking ,the Status Led will go out at the same time , If the original link connecting the receiver

(Registration)is longer than 10 minutes The LED will flicker showing the 1HZ rate, At this time

the receiver and transmitter will go into data transfer mode. Press Transmitter for 4 seconds, when

transmitter connects, it will go into search mode waiting for the other receivers and the connection

(registration),press Comb Key in 10 seconds it will then connect with the original link

(registration) receiver . After connected the Receiver will be open the Wii Nunchuk power , and

activate the Wii Nunchuk this will procreant signal switched to RF signal modules which can be

identified by the microprocessor, in the temporary register, it will also send out completed date

when after received a receiver emitted data conversion orders Low voltage denote：When the

Transmitter battery voltage low then 1.8V，LED flicker showing the 4Hz rate，This time system

will can't in gear working. The transmitter power source use may charge the pattern design, may

USB which inputs the 5V DC voltage transform can supply two 1.3V NI-MH rechargeable battery

charge the electric circuit, the use voltage control technology, during charge instructed the charge

condition, and guaranteed can let the battery as far as possible fill .Simultaneously also has two

nickel hydrogen battery transforms the voltage is the 3.3V regulated voltage boosted circuit, thus

enables the electric circuit to work in the voltage quite low situation .May divide into the charge

part and the constant voltage part, in which receiver part only then the constant voltage part, is

same with the transmitter. The USB 5V voltage dropping arrives 3.8V afterwards after the diode,

then supplies for the following current limiting resistor and the linear voltage dropping part,

through examines on the current limiting resistor the voltage to judge the electric current the size,

when the charging current is smaller than 80mA to shut off charges LED, achieves the instruction

charge degree the goal .This part will use TL431 and the triode combination the output voltage

stabilizes in 2.85V, the output voltage will stabilize according to the NI-MH battery characteristic

in 2.85V, will make the rechargeable battery the highest voltage to maintain at this position, will

achieve the battery fill.

Connect the Wii Remote with the receiver and the Wii Remote with the Console, also connect the

receiver with the Wii Nunchuk and installed the battery according to the instructions. At this time

the transmitter will be in sleep mode, press the comb key to wake up transmitter, the transmitter

into the search mode, Status LED flashes to 2 Hz, and then wait for the receiver to connect with

the transmitter, if any receiver is in connection mode, transmitter and the receiver will be reset

identification ID and confirmed to use of other channel connection (registration), After the

wireless Transmitter is connected it will register with the receiver ,and the transmitter Status LED

flashes with the 1hz. Transmitter and receiver will turn into data transfer mode. With the

PAGE 1
USER MANUAL Wireless nunchuk is applicable to Wii Remote Control use, the original Wii Remote Control and Nunchuk were wired connections to connect them, Due to wired connection the gaming distance was limited, This product is away from way of use the limit as the improvement. the Nunchuk transmitting end distance may amount to 5-6 meter.
PAGE 2
transmitter press the Comb Key to awaken the transmitter, the transmitter then will go into the search mode , the transmitter status LED will flash 2 Hz. When the receiver is in the search mode, the receiver connection led will flash 2 Hz.
PAGE 3
Connection status： 1.Online status of the Transmitter break the connection： When the receiver and the Transmitter has been in connection line status, if connection is cut, the Transmitter will return into the search mode, Connection LED will flash with 1 Hz, Transmitter connected or press comb key again, the receiver and the transmitter can be connected again. 2.
PAGE 4
LED flashes to 1Hz, the Transmitter part has also entered search mode, Status LED 1 Hz will flicker, at this time need press the comb keys for 4 seconds and will automatically make the Transmitter into the search mode to connect with the receiver line registration or wait for the transmitter dormancy mode then click Comb awakened transmitter and receiver can be connected to re-register line.