User's Manual

ManualsBrandsStorm Electronics ManualsElectronicsWIRELESS MINI CONTROLLER

USER MANUAL

Wireless Mini Controller is applicable to Wii Remote Control use, the original Wii Remote Control

and Wireless Mini Controller were wired connections to connect them, Due to wired connection the

gaming distance was limited, This product is away from way of use the limit as the improvement. the

Wireless Mini Controller transmitting end distance may amount to 5-6 meter. Transmitter has

searching key, when press the searching key , the LED will flicker with 2HZ rate, if in 10 seconds it

does not connect with the receiver then it will automatically enter the dormant linking ,the Status Led

will go out at the same time , If the original link connecting the receiver (Registration)is longer than

10 minutes The LED will flicker showing the 1HZ rate, At this time the receiver and transmitter will

go into data transfer mode. Press Transmitter for 4 seconds, when transmitter connects, it will go into

search mode waiting for the other receivers and the connection (registration),press Comb Key in 10

seconds it will then connect with the original link (registration) receiver . After connected the

Receiver will be open the Wii Nunchuk power , and activate the Wii Nunchuk this will procreant

signal switched to RF signal modules which can be identified by the microprocessor, in the temporary

orders Connect the Wii Remote with the receiver and the Wii Remote with the Console, also connect

the receiver with the Wii Nunchuk and installed the battery according to the instructions. At this time

the transmitter will be in sleep mode, press the searching key to wake up transmitter, the transmitter

into the search mode, Status LED flashes to 2 Hz, and then wait for the receiver to connect with the

transmitter, if any receiver is in connection mode, transmitter and the receiver will be reset

identification ID and confirmed to use of other channel connection (registration),After the wireless

Transmitter is connected it will register with the receiver ,and the transmitter Status LED flashes with

the 1Hz. Transmitter and receiver will turn into data transfer mode. With the transmitter press the

searching Key to awaken the transmitter, the transmitter then will go into the search mode , the

transmitter status LED will flash 2 Hz. When the receiver is in the search mode, the receiver

connection led will flash 2 Hz.

Connection status：

1.Online status of the Transmitter break the connection：

When the receiver and the Transmitter has been in connection line status, if connection is cut, the

Transmitter will return into the search mode, Connection LED will flash with 1 Hz, Transmitter

connected or press comb key again, the receiver and the transmitter can be connected again.

2. Online status of the transmitter mandatory break the connection：

When the receiver and the transmitter has been in connection status, Press Comb key for 4 seconds ,

the transmitter will go into the search mode, the transmitter Status LED flashes to 2 Hz, and the

original receiver interrupted, the receiver will go to the connected Line mode, the receiving end of the

Status LED flashes to 1 Hz. As in the original transmitter into the search mode of

<10seconds>between the transmitter is unable to obtain new lines connecting the receiver, transmitter

will go into sleep status. If the transmitter goes into search mode press the button to connect Comb

model line, then the receiving end with the completion of connecting lines.

3. Receiver in the search mode of connection methods：

Receiver into the search mode, Connect LED flashes to 2 Hz, at this time, if more than

two-transmitters are entered, the registration or connecting line mode, the receiver will be

complete registration with any Transmitter which it has not Connected.

4. Transmitter in the search mode of connection methods：

Transmitter into the search mode, Status LED flashes to 2 Hz, at this time, if more than

two-receiver into the search mode, The transmitter will complete the register of the connection

with any receiver which it has not connected to before.

5. Re-plug the receiver connection：

When the receiver and the transmitter has been in connecting line status, such as receiver will be

inserted under the Wii Remote stuck again, this time receiver turn into the search mode, Connect

LED flashes to 1Hz, the Transmitter part has also entered search mode, Status LED 1 Hz will

Summary of content (2 pages)

PAGE 1
USER MANUAL Wireless Mini Controller is applicable to Wii Remote Control use, the original Wii Remote Control and Wireless Mini Controller were wired connections to connect them, Due to wired connection the gaming distance was limited, This product is away from way of use the limit as the improvement. the Wireless Mini Controller transmitting end distance may amount to 5-6 meter.
PAGE 2
flicker, at this time need press the comb keys for 4 seconds and will automatically make the Transmitter into the search mode to connect with the receiver line registration or wait for the transmitter dormancy mode then click Comb awakened transmitter and receiver can be connected to re-register line. When the transmitter and receiver finish search mode, They will save each the compellation ID. FCC NOTE: This device complies with Part 15 of the FCC Rules.