INSTALLATION MANUAL
Contents 1 2 3 4 5 6 7 8 8.1 8.2 8.
1 Compliance Statement This equipment complies with Federal Communications Commission (FCC) and Industry Canada (IC) radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter, except in accordance with multi-transmitter product procedures.
FCC Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
RSS-Gen & RSS-247 statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter, except in accordance with multi-transmitter product procedures.
Warning Do not use the device while the vehicle is in motion. Always stop the vehicle safely to use the device. Failure to do so may lead to serious injury or death.
2 FleetArc Kit Contents • FleetArc Gateway • Main harness • USB cable • Cavity plug connector • User manual • Accessory kit: • Zip ties • Double sided tape or Industrial Velcro • Scotchlok connectors • ELD Exclusive Items: • ELD Vehicle sticker • Driver ELD user manual • 2 QR Code Stickers • Quick Guide 10
3 Module Overview LED indicator USB Connector Connector #1 Connector #2 Connector #3 Fixation brackets 11
4 Fixation Options Double-sided tape or velcro Zip ties Screws 12
5 Module Orientation To improve GPS reception, always keep LED side facing up.
6 FleetArc Gateway Connectors #3 #2 #1 USB Mechanical patterns prevent wrong conector insertion 14
7 Status LED Indicator FleetArc Gateway features a red LED to provide a visual reference for LTE network and GPS coverage status, aiding in the installation process. The table below describes the status for each LED blinking pattern.
8 Harness Options FleetArc Gateway is shipped with either one out of two options of main cable harness: • OBD Harness, better suited for quick installations, such as ELD applications) with the most commonly found diagnostic connectors available on the market • Hard Wire Harness, better suited for customers that wish to use the full capabilities of the FleetArc Gateway device.
8.1 OBD Harness installation The OBD Harness, better suited for baseline and ELD applications, features an adapter connector, used to connect FleetArc Gateway with the most commonly diagnostic connectors available on the market.
With the accessories and the Low-range connectors, it is possible to quickly connect FleetArc Gateway to the vehicle diagnostic bus using the following scheme: 6 pin Connector 9 pin Connector Deutsch 6-pin connector Deutsch 9-pin connector OBDII Connector OBD-II connector RP1226 Connector RP1226 connector 18
1. Find the vehicle’s diagnostic port. Its position may vary depending on the vehicle make and model. You might find the diagnostic port: • • • • • Under the dash or under the steering column/wheel on the left or right, On the left or right of the pedals, above the pedals, Above the footrest, In the fuse box, Near the handbrake or the clutch pedal handbrake / footbrake. In some cases you may have to remove a plastic cover to find the connector.
2. Attach the device to the vehicle’s diagnostic port. In the case of the 9-pin or 6-pin connector, rotate the collar to line up the collar tabs with the matching slot on the diagnostic port. Press firmly until the connector is fully attached. Then rotate the collar clockwise until it locks. In the case of the OBDII and RP1226 connectors, line up the connector so it exactly matches the diagnostic port in the vehicle. Press firmly until the connector is fully attached.
8.2 Hard Wire Harness installation The Hard Wire Harness is better suited in cases where full FleetArc telematics capabilities are required, using all of the 3 available connectors. In order to properly install FleetArc Gateway with the Hard Wire Harness, use the full harness diagram and the scotchlok connectors, both provided in the box or the OEM recommended splice connection.
8.3 USB Cable FleetArc Gateway features a USB 2.0 interface that can be used as an alternative interface with the end-user phone/tablet. To use it, attach the USB cable provided in the box to the USB connector on your FleetArc Gateway. Afterwards, connect the phone/tablet USB cable to the female USB interface.
9 Warranty The Stoneridge FleetArc is covered by a 12 month warranty period from the date of shipment, to materially conform to our published specifications and be free from material defects. Please refer to our Terms and Conditions at www.fleetarc.com for full details on our Warranty and Returns and Refunds policy.
For any queries on the Stoneridge FleetArc please contact Customer Support on: Tel.: +1 (883) 994-3953 Email: eldsupport@stoneridge.com © Stoneridge Aftermarket Inc. 151473000 – Rev.