UM1761 User manual Evaluation board for ST95HF NFC transceiver Introduction The EVAL-ST95HF is a ready-to-use development kit used to evaluate functions and performances of the RF transceiver ST95HF in Reader mode, Card emulation mode or Peer to Peer Mode for standard contactless applications.
Contents UM1761 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Hardware and layout description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1 Eval-ST95HF assembly drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.2 Eval-ST95HF board powering and Startup . . . .
UM1761 List of tables List of tables Table 1. Table 2. Table 3. Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of figures UM1761 List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. 4/19 Functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Top assembly view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bottom assembly view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UM1761 1 Description Description The EVAL-ST95HF board includes a ST95HF transceiver, a 4 turns 47 X 34 mm, 13.56 MHz inductive etched antenna ant its associated tunings components, a STM32F103 32-bits microcontroller with 1Mbytes of Flash memory and a TFT LCD 2.4 inch and 240*230 resolutions. The functional scheme is shown in Figure 1. It is powered by USB cable. A SPI bus allows the microcontroller to communicate with the ST95HF and LCD screen. A 4 positions joystick is used to move in the menu.
Features 2 UM1761 Features • ST95HF, a 13.56-MHz multi-protocol contactless transceiver IC with SPI serial access communication: • Reader mode • – ISO/IEC 14443 Type A – ISO/IEC 15693 – ISO/IEC 18092 Card Emulation mode: – 6/19 ISO/IEC 14443 Type A • ISO/IEC 14443 Type A in Peer To Peer mode. • 47 x 34 mm with 4 turn. 13.56 MHz inductive antenna etched on PCB and associated tuning circuit.
UM1761 Hardware and layout description 3 Hardware and layout description 3.1 Eval-ST95HF assembly drawing The top and bottom assembly views are shown in Figure 2 and Figure 3, respectively. Figure 2. Top assembly view 5HVHW SXVK EXWWRQ 86% FRQQHFWRU 3RZHU VXSSO\ SLQV -7$* FRQQHFWRU 3URWRFRO GHWHFWLRQ /('V WXUQV 0+] ORRS DQWHQQD /&' VFUHHQ SLFWXUH URWDWLRQ SXVK EXWWRQ /&' VFUHHQ -R\VWLFN *URXQG SUREH 5) ILHOG GHWHFWLRQ /(' 0+] ;7$/ 67 +) ,& 06 9 Figure 3.
Hardware and layout description UM1761 Figure 4. EVAL-ST95HF RF transceiver board top picture Figure 5. EVAL-ST95HF RF transceiver board back picture 3.2 Eval-ST95HF board powering and Startup The EVAL-ST95HF board is powered by the USB bus via a Type A / mini B USB cable connected to a PC. When powered up, the ST95HF starts the firmware already downloaded in STM32 flash memory.
UM1761 Hardware and layout description Please refer to the firmware user manual available on ST web site www.st.com to get more detail. 3.3 Program/debug the RF transceiver demo board. In order to flash or debug an STM32 microcontroller application on the EVAL-ST95HF board, simply connect the 20-pin JTAG/SWD flat ribbon of the STLINK/V2 in-circuit debugger and programmer to the RF transceiver demonstration board JTAG connector (J3), then launch STLink.
Hardware and layout description 10/19 Figure 6.
Bill of material UM1761 4 The parts needed for the EVAL-ST95HF development kit are listed in Table 2. Table 2. Bill of materials DocID026283 Rev 2 Description Reference Package Manufacturer Part number Distributor Order code 1 ST95HFVMD5 ST95HF U1 VFQFPN32_5x5 STMicroelectronics ST95HF VMD5T - - 1 MCU 32 BITS 1MB Flash 64LQFP STM32F103RGT6 U2 LQFP64_10x10 STMicroelectronics STM32F103RGT6 - - 1 3.
DocID026283 Rev 2 Quantity Description Reference Package Manufacturer Part number Distributor Order code 2 CONDENSATEUR MLCC 0603 NP0 50V 2% 47pF C22, C25 0603 Murata(2) GRM1885C1H470GA01 - - 4 CONDENSATEUR MLCC 0603 NP0 50V 2% 100pF C23, C24, C35, C36 0603 Murata(2) GRM1885C1H101GA01 - - 1 CONDENSATEUR MLCC 0603 NP0 50V 2% 82pF Ca 0603 Murata(2) GRM1885C1H820GA01 - - 2 CONDENSATEUR MLCC 0603 NP0 50V 5% 10pF C27, C28 0603 - - Farnell 1759053 2 CONDENSATEUR MLCC 0603
DocID026283 Rev 2 Description Reference Package Manufacturer Part number Distributor Order code 1 FILTER SUPPRESSION, 0603, 1UF, 6.3VDC NFM18PS105R0J3D FL3 NFM18PS Murata(2) NFM18PS105R0J3D Farnell 1686506 5 FERRITE CMS 600OHM. 0805 742792042 L1, L2, L3, L8, L9 0805 WURTH ELEKTRONIK(2) 742792042 Farnell 1635716 1 FERRITE CMS 2200OHM. 0805 742792093 L10 0805 WURTH ELEKTRONIK(2) 742792093 Farnell 1635726 1 FERRITE BEAD, 0.
DocID026283 Rev 2 Description Reference Package Manufacturer Part number Distributor Order code 2 Resistance CMS 0603 0,1W 5% 330 Z-RX1, Z-RX2 0603 - - - - 1 Resistance CMS 0603 0,1W 5% 560 R43 0603 - - - - 3 Resistance CMS 0603 0,1W 5% 1k R2, R44, R45 0603 - - - - 1 Resistance CMS 0603 0,1W 5% 1.5k R28 0603 - - - - 5 Resistance CMS 0603 0,1W R17, R18, 5% 3.3k R19, R23, R24 0603 - - - - 10 Resistance CMS 0603 0,1W 5% 4.
Quantity Description 2 Connector 1PT, NC 1 2 Connector 3PTS 2,54, NC(1) Push Button SW_BP_ST (1) Reference Package Manufacturer Part number Distributor Order code ST1, ST3 CON_1PTS FCI 77311-401-36LF Farnell 1097954 ST2 CON_3PTS_P2.
DocID026283 Rev 2 Description Reference Package Manufacturer Part number Distributor Order code 6 PCB MIRE(1) MIRE1, MIRE2, MIRE3, MIRE4, MIRE5, MIRE6 MIRE - - - - 1 PCB(3) 150mmx60mmx1.6mm (FR4, dual side, components on both sides, green color) - - - - - - 5 Bumpon protective product - 3M SJ5306 - - - 1 Five_way switch button hat, PB-504/PB-MT008A (Cyan), along, AKG004, for U4 - - - - - - 1 Carton box(1) - - - - - - Quantity Bill of material 16/19 Table 2.
UM1761 Federal Communications Commission (FCC) and Industry Canada (IC) compliance state- 5 Federal Communications Commission (FCC) and Industry Canada (IC) compliance statements 5.1 FCC Compliance Statement 5.1.1 Part 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 5.1.
Revision history 6 UM1761 Revision history Table 3. Document revision history 18/19 Date Revision Changes 20-Jun-2014 1 Initial release. dd-Mar-2015 2 Added Section 5: Federal Communications Commission (FCC) and Industry Canada (IC) compliance statements.
UM1761 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.