User's Manual

ManualsBrandsSTL International ManualsElectronicsWireless Receiver

Confidential

WR-4 Alarm Receiver

User Manual

WR-4 is a centralized alarm receiver to receive alarms transmitted by

different models of alarm Transmitters: WT-1, WP-1, WFM-1. It gives

audio and visual indication to tell which programmed transmitter is

sending the alarm.

1. Control Buttons

1.1 POWER button

1.2 ALARM RESET button

1.3 PROGRAM button

1.4 CONFIRM button

2. Indicators

2.1 Power on indicator

2.2 Programming Indicator

2.3 Station Indicator

3. Power Connector

3.1 9V AC adapter

4. Installation

4.1 Plug in the AC adapter

4.2 Press the Power button to turn on the power. The red LED should be

ON.

4.3 Program the alarm transmitters into the monitor locations using the

procedures in Section 5.

4.4 Test the completion of installation by pressing the “Check” button

on the Model WT-1 transmitter or activate an alarm from the Pendant

(Model WP-1)or wireless floor mat transmitter(Model WFM-1)

5. Program a Model WT-1 Sentry Transmitter Location

5.1 Press PROPRAM button on Receiver for two seconds

5.2 Green LED will lit

5.3 Red Station LED will flash

5.4 Alarm tone pattern #1 will sound at low level

5.5 Press PROGRAM button to select the next empty location

5.6 Alarm tone pattern #2 will sound at low level

5.7 Press CHECK button on Transmitter until a long beep is heard from

the Receiver and the station LED stops flashing

5.8 Press PROGRAM to program next empty station

5.9 Press CONFIRM button to return to normal monitor mode

5.10 programming can be checked any time by pressing the CHECK button

on the Transmitter

6. Program a Model WP-1 Pendant Location

6.1 Press PROPRAM button on Receiver for two seconds

6.2 Green LED will lit

6.3 Red LED will flash indicating the first empty station location

6.4 Alarm tone pattern #1 will sound at low level

6.5 Press PROGRAM button to select the next empty location

6.6 Alarm tone pattern #2 will sound at low level

Summary of content (3 pages)

PAGE 1
Confidential WR-4 Alarm Receiver User Manual WR-4 is a centralized alarm receiver to receive alarms transmitted by different models of alarm Transmitters: WT-1, WP-1, WFM-1. It gives audio and visual indication to tell which programmed transmitter is sending the alarm. 1. Control Buttons 1.1 POWER button 1.2 ALARM RESET button 1.3 PROGRAM button 1.4 CONFIRM button 2. Indicators 2.1 Power on indicator 2.2 Programming Indicator 2.3 Station Indicator 3. Power Connector 3.1 9V AC adapter 4. Installation 4.
PAGE 2
6.7 Press ALARM button on Pendant until a long beep is heard from the Receiver and the station LED stops flashing 6.8 Press PROGRAM to program next empty station 6.9 Press CONFIRM button to return to normal monitor mode 7. Program a Model WFM-1 Sentry Mat Location 7.1 Press PROGRAM button on Receiver for two seconds 7.2 Green LED will lit 7.3 Red LED will flash indicating the first empty station location 7.4 Alarm tone pattern #1 will sound at low level 7.
PAGE 3
12.2 Operating procedure is same as Sentry alarm except a single tone alarm at 2 HZ is sounded. 13. Battery Low Indication 13.1 When Battery Low message is received, the corresponding LED will flash at 0.5 Hz. 13.2 Other operating procedure is same as Sentry alarm except 14. Log off Sentry Transmitter 14.1 When an alarm is triggered, Care giver can log off the Sentry Transmitter by steps 10.4 – 10.7 14.2 The Receiver will not monitor out of range for a logged off Transmitter. 15.