User Manual

steute Schaltgeräte GmbH & Co. KG Brückenstraße 91, 32584 Löhne, Germany, www.steute.com
//
SW 100 AMB INT / SW 100 AMB EXT
Instruction for use
Instructions d'utilisation
English
Table of contents
Model and type designation .................................................................. 1
Table of contents .............................................................................. 1
General information ............................................................................. 1
Regulatory and Safety Compliance European Union ....................... 1
FCC Regulatory Information ................................................................ 1
Other regulatory notes for OEM ........................................................ 2
A separate approval ........................................................................... 2
Standards ............................................................................................. 2
Instructions for use of SW 100 AMB
This manual explains how to integrate the module into the end pro-
duct. It includes procedures that shall assist you to avoid unforeseen
problems.This manual presents information that shows how the mo-
dule or OEM product (with integrated module) complies with regula-
tions in certain regions.
Model and type designation
SW 100 wireless module
General information
This module has to be installed and used in accordance with the tech-
nical description/installation instructions provided by the manufactur-
er. For detail information concerning type approval of this module (e.g.
where this module is already pre-approved) please contact the author-
ized local distributor or the manufacturer. The system may only be im-
plemented in the configuration that was authorized. Note that any
changes or modifications to this equipment not expressly approved by
the manufacturer could void the user`s authority to operate this
equipment.
Regulatory and Safety Compliance European Union
Declaration about performed tests
The steute module is a wireless data transmission system. This RF
module can be integrated into various end products. steute declares
that the module complies with the following directive and standards:
Satisfy all the technical regulations applicable to the product within
the scope of council directives LVD 2006/95/EC, EMC 2004/108/EC,
R&TTE 1999/5/EC and RoHS 2011/65/EC if used for its intended pur-
pose and that the following norms, standards or documents have been
applied:
- EN 301 489-1, EN 300440-1 V1.6.1: 2010-08
- EN 301489-1 V1.9.2, -3 V1.6.1
- EN 62479: 2010
The technical documentation as required by the Conformity Assess-
ment procedure is kept at the following address:
steute Schaltgeräte GmbH & Co.KG
Brückenstraße 91
32584 Löhne, Germany
Telephone ++49 (0) 57 31 / 7 45 – 0
Telefax ++49 (0) 57 31 / 7 45 – 200
eMail: [e-mail]
www.steute.com
Labelling
CE conformity marking for product.
OEM product/application, where this wireless module is integrated/in-
stalled in, has to be labelled in accordance to Article 12 of the R&TTE
directive. A label has to be permanently affixed to the OEM product/ap-
plication. Otherwise OEM product must be approved separately.
Regulatory information on the OEM devise should contain labelling
like: Approved in accordance to R&TTE directive transmitter module
marked by CE, manufactured by steute incorporated to OEM product.
More detailed information in chapter “A separate approval”.
FCC Regulatory Information
The Federal Communication Commission Radio Frequency Interfer-
ence Statement includes the following paragraph.This equipment has
been tested and found to comply with the limits pursuant to Part 15 of
the FCC Rules.These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installation. This
equipment generates, uses and radiates radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
Radiofrequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance of 20cm between the radiator
and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. Not Authorized
modification could void authority to use this equipment.