Wiring Instructions

ManualsBrands.steute Schaltgeraete ManualsElectronicsRadio inclination sensor

steute Technologies GmbH & Co. KG

Brückenstraße 91, 32584 Löhne, Germany, www.steute.com

RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe

1 / 10

Mounting and wiring instructions / Wireless tilting sensor

English

Use of the mounting and wiring instructions

All actions described in these instructions may only be performed by

qualified persons who have been trained and authorised by the

operating company.

1. Read and understand these mounting and wiring instructions.

2. Comply with the valid occupational safety and accident prevention

regulations.

3. Install and operate the device.

Selection and installation of devices and their integration in control

systems demand qualified knowledge of all the relevant laws, as well

as the normative requirements of the machine manufacturer.

Scope of delivery

1 device, mounting and wiring instructions, carton.

Safety information

In this document, the warning triangle is used

together with a signal word to indicate a

hazardous situation.

The signal words have the following meanings:

NOTICE

indicates a situation which may

result in material damage.

CAUTION

indicates a situation which may

result in minor or moderate

injury.

WARNING

indicates a situation which may

result in serious injury or death.

DANGER

indicates a situation which will

result in serious injury or death.

General information

NOTICE

After installation and during the operation of

the NGF system in connection with the crane

system, additional hazards may occur. These

hazards go beyond the framework of these

mounting and wiring instructions. They must be

documented by the manufacturer of the

overall system.

NOTICE

The NGF system is subject to speciﬁc preven-

tive measures in terms of electromagnetic

compatibility. Install and operate it in accord-

ance with the used standards listed in the

technical data section in this document.

Intended use

The wireless tilting sensor monitors the position of the bottom hook

block of a crane and helps to hold it in a horizontal position.

As a second application, it monitors the position of a load (e.g. with a

parallel lift).

NGF Tx

NGF Rx

Summary of content (10 pages)

PAGE 1
// RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe Mounting and wiring instructions / Wireless tilting sensor English Intended use Use of the mounting and wiring instructions All actions described in these instructions may only be performed by qualified persons who have been trained and authorised by the operating company. 1. Read and understand these mounting and wiring instructions. 2. Comply with the valid occupational safety and accident prevention regulations. 3. Install and operate the device.
PAGE 2
// RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe Mounting and wiring instructions / Wireless tilting sensor English RF Rx NGF ULR2.4-safe (receiver) 8 System components 8 The system consists of a transmitter (Tx) and a receiver (Rx). The transmitter measures the angles and transmits the measured values via radio. The measured values are determined by two independent measuring systems. The radio link is a 2.4 GHz low-energy system. The transmitter is powered by batteries or accumulators.
PAGE 3
// RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe Mounting and wiring instructions / Wireless tilting sensor English Battery Installation = = WARNING Loose screws can cause parts to come loose and fall off. Tighten all cover screws hand-tight. The mechanical installation of the transmitter and receiver is the responsibility of the system operator. The type of mounting and the mounting screws must be appropriate for the intended application. The maximum diameter of the bore hole is 6.5 mm.
PAGE 4
// RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe Mounting and wiring instructions / Wireless tilting sensor English To set the devices to Pairing Mode: - Tx: press the pairing button on top of the inner case for >5 seconds. - Rx: send the LSB pairing command. The command must include the transmitter serial number (to be found on the Tx label). After both devices have been set to Pairing Mode, the receiver will send the new pairing ID to the transmitter.
PAGE 5
// RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe Mounting and wiring instructions / Wireless tilting sensor English Troubleshooting The wireless signal is attenuated on the way from the transmitter to the receiver. In addition, the wireless signal is attenuated by obstacles. The degree of attenuation depends on the material of the obstacle. Ideally, with a direct line of sight, the wireless range will be greater than 300 m.
PAGE 6
// RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe Mounting and wiring instructions / Wireless tilting sensor English USA: FCC - Title 47 CFR Part 15 Canada: RSS - 247 Issue 2 Notice: Changes or modifications made to this equipment not expressly approved by (steute) may void the FCC authorization to operate this equipment. Compliance This wireless system has been found to comply with several national and international directives which are listed and explained as follows.
PAGE 7
// RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe Mounting and wiring instructions / Wireless tilting sensor steute Technologies GmbH & Co. KG Brückenstraße 91, 32584 Löhne, Germany, www.steute.com Dimensions RF Tx NGF ULR2.4-safe RF Rx NGF ULR2.4-safe Production date Pin assignment of RF Rx NGF ULR2.4-safe Production date on type label: DD.MM.
PAGE 8
// RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe Mounting and wiring instructions / Wireless tilting sensor Technical data RF Tx NGF ULR2.
PAGE 9
EU-KONFORMITÄTSERKLÄRUNG // RF Tx NGF ULR2.4-safe / RF Rx NGF ULR2.4-safe EU DECLARATION OF CONFORMITY gemäß der Funkanlagen-Richtlinie Mounting and wiring instructions / Wireless tilting2014/53/EU sensor according to RED 2014/53/EU Als Hersteller trägt die Firma steute Technologies die alleinige Verantwortung für die Ausstellung dieser Konformitätserklärung / As manufacturer, steute Technologies is solely responsible for issuing this Declaration of Conformity.
PAGE 10
Zusatzinformation zu Montage- und Anschlussanleitungen Additional information on mounting and wiring instructions Information complémentaire aux instructions de montage et de câblage Ulteriori informazioni sulle istruzioni di collegamento e montaggio Informação adicional para as instruções de montagem Дополнительная информация по монтажу и инструкциям по подключению [bg] П ри поискване Вие ще получите тази асамблея, а също и връзката ръчно майчиния си език.