Installation Instructions

ManualsBrandsSterling Home & Patio ManualsOutdoorsCanterbury Swivel Rocker Dining Patio Chair

ADL14801

FOOT CAP

FACTORY ASSEMBLY

FC0063

FOOT CAP

Page 2

NOTE: MAKE SURE ARROWS

FROM BOTH THE "U" BAR

AND ROCKER ASSEMBLY

ARE POINTING IN THE

SAME DIRECTION!

IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!

TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT

HEX WRENCH-1

HW0008

HEX WRENCH-2

HW0007

G0228

QTY

PARTS LIST

DESCRIPTION

ORDER PART #

*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE

BOLT COVER-1

HW0028

QTY

SWIVEL BASE &

ROCKER

ASSEMBLY

5/16" X 40 MM

BOLT

Ø8.0 X 2.3 MM

SPRING WASHER

HW0003

5/16" NUT

HW0015

"U" METAL

PLATE

CHAIR FRAME

PARTS LIST

DESCRIPTION ORDER PART #

HW0295

HW0618

ROCKER PLATE

FACTORY ASSEMBLY

COVER

FACTORY ASSEMBLY

G0161

COVER

SEAT DESIGNS MAY

VARY BUT THE ASSEMBLY

IS THE SAME

Figure 1

Figure 2

ROCKER PLATE

"U" BAR

ROCKER

ASSEMBLY

"U" BAR

BOLT COVER-2

HW0105

Step 1:

Do not attempt assembly if any parts are missing or damaged.

Step 2:

Step 3: Important: We recommend 2 people work together to assemble the chair.

If chair frame has

been properly positioned on the rocker assembly, all arrows on the "U" bar and rocker

assembly will be pointing in the same direction.

Step 4: Critical Step: The "U" metal plates must be installed in the proper location.

Hand tighten nuts 3-4

revolutions only.

CAUTION: Failure to place "U" metal plates under the rocker plates and above the

"U" bar exactly as shown in diagram will cause the bolt heads and nuts to damage the

structure of the rocker plates and the "U" bar. Damage due to over tightening of bolts

or improper assembly could cause injury and may void your warranty.

Step 5: Make sure the bolts are

fully tightened.

Step 6:

Identify all parts packed in the carton against the parts list. Remove all protective materials.

Place parts on a non-abrasive surface to avoid scratching. If you are missing any parts or are

unsure as how to proceed with the assembly, call our Customer Service Center at

1-800-416-3511.

Place the swivel base (with rocker assembly) on a flat, solid surface. Make sure the rocker

assembly is positioned all the way into the base. It may have shifted or vibrated out during

shipment.

Note the

arrow labels on the "U" bar and the rocker assembly. Also note the horseshoe shape of the

rocker plate. Point the open end of the horseshoe away from you. The arrows on the rocker

assembly should be pointing towards you. Set the chair frame on the rocker assembly with

front of the seat facing you and the arrows on the "U" bar pointing towards you as shown

in . This is very important for a safe, balanced rocking motion.

Insert the "U" metal plate, so that the "U" bar and rocker plate

are between both sides of the "U" metal plate. Make sure that the holes in the "U" metal

plate are completely aligned with the holes in the "U" bar as shown in . Guide the

bolts through the holes on the top side of the "U" metal plate, through the holes in the

"U" bar, through the holes in the rocker plate and then, most importantly, through the holes

in the bottom side of the "U" metal plate. It is very important that the holes in the bottom

of the "U" metal plate are placed directly beneath the holes in the rocker plate. Add a

spring washer and a nut to each bolt as shown in .

Repeat the same procedure on the other side.

Tighten all nuts and bolts with the hex wrenches provided.

Remove arrow labels from the "U" bar and rocker assembly. Cover bolts

with bolt covers.

Your chair should be ready for use. If your chair is not rocking properly, double-check your

assembly procedure, especially Step 3. If the chair rocks too far forward to or is difficult to

rock backwards, you have probably installed the seat frame backwards on the rocker

assembly. If you need further assistance, please call our Customer Service Center

at 1-800-416-3511.

Figure 1

Figure 2

Read this

step and carefully examine.

IMPORTANT NOTE: Damage to frames or spring plates resulting from not FULLY

tightening the bolts, is not covered under warranty. Please read all instructions carefully

before assembly. If you have any questions regarding your assembly, call our Customer

Service Center at 1-800-416-3511.

SLING TUBE CAP

FACTORY ASSEMBLY

FC0082

AR20046

AR20047

Summary of content (2 pages)

PAGE 1
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!! TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT Step 1: Identify all parts packed in the carton against the parts list. Remove all protective materials. Place parts on a non-abrasive surface to avoid scratching. If you are missing any parts or are unsure as how to proceed with the assembly, call our Customer Service Center at 1-800-416-3511.
PAGE 2
CARE AND MAINTENANCE SKU # 272-4579 FRAMES Cleaning - Use mild soap and warm water. Do not use abrasive materials, cleansers or bleach products. Rinse with clean water and dry thoroughly. Caterbury Alum Sling Swivel Rocker Customer Service 1-800-416-3511 Maintenance - Periodically clean and dry thoroughly. Be sure to drain any water accumulated inside the frames. To thoroughly drain frames, remove foot caps and tilt the frames, if necessary, to remove all water. This is critical.