User's Manual

ManualsBrandsSTEELMATE ManualsElectronicsTransmitter

DS-7

2-WAY REMOTE START SYSTEM

OPERATING INSTRUCTIONS

CONGRATULATIONS on your choice of a Data Start™ Remote Engine Starter and Keyless Entry by Crimestopper

Security Products Inc. This system is designed to work exclusively thru the vehicle’s Canbus using a Databus

interface module. This booklet contains the information necessary for operating your system. If any questions arise,

contact your installation dealer or Crimestopper Security Products Inc.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be conne

cted in order for the system to operate properly i.e. Remote

Start connections, Flashing lights, and Brake Reset. For programming, the program button is required.

-OPTIONAL: These features are to be connected only if desired or agreed upon by the customer and the installing

dealer i.e. Door Locks, Trunk Pop, Dome Light Illumination, Horn-Honk, Anti-Grind, etc. These features may also

require additional parts and/or labor fees. Consult with your installer beforehand to be sure of what is going to be

installed with your particular system.

RIMESTOPPER SECURITY PRODUCTS, INC.

1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV 11.2012

This device complies with FCC Rules part 15. Operation is

subject to the following two conditions: 1) This device may not

cause interference, and (2) this device must accept any

interference that may be received, including interference that

may cause undesired operation. The manufacturer is not

responsible for any radio or TV interference caused by

unauthorized modification to this equipment. Such modification

could void the user's authority to operate the equipment.

MODEL: 5154

Summary of content (20 pages)

PAGE 1
DS-7 2-WAY REMOTE START SYSTEM MODEL: 5154 OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Data Start™ Remote Engine Starter and Keyless Entry by Crimestopper Security Products Inc. This system is designed to work exclusively thru the vehicle’s Canbus using a Databus interface module. This booklet contains the information necessary for operating your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.
PAGE 2
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….………………………………….…………….….…………2 Using the 2-Way Pager……………………………………………….……………………….………....…………...3-4 Setting the Clock and Beep or Vibrate Selection…………………………………………………….……….….4-5 1-Way Sidekick and Battery Replacement………….………………...……………………..…………….………..6 Status LED………………………………………………………………………………………………..……….….……7 Remote Engine Control…………….…..……………………………………………………………….…….…..…7-10 Turbo Timer Mode……………………………….……………………………………...……………….…………..….
PAGE 3
USING THE 2-WAY PAGER TRANSMITTER SIDE BUTTONS LCD SCREEN ICONS Valet Mode (Tools) Transmit Signal Battery Life Ignition ON Hood Open Lock/Unlock (Arm/Disarm) Silent no beeps Sensor Warning (Small Hammer) Sensor Trigger (Big Hammer) Door Open CLOCK / Run Count Down VEHICLE SELECT Trunk Open Remote Started LOCK / ARM TRUNK RELEASE UNLOCK / DISARM REMOTE START USB Charger (Under Side Cover) AUX Outputs thru Data Note: Some Icons on the LCD display only function on the Combo Alarm with Remote S
PAGE 4
USING THE 2-WAY PAGER TRANSMITTER The 2-Way LCD Pager remote transceiver is used to send and receive information from the vehicle. The Control Module transmits High Frequency FM signals from the vehicle to your pager over long distances. Your range will vary depending on location, terrain, and local RF noise/interference. This system is not guaranteed to page you if you are behind concrete walls, underground, in a large structure, or in an area with high levels of electronic interference.
PAGE 5
REMOTE BEEP & VIBRATE SELECTION The LCD pager remote BEEPS and VIBRATES when it receives a signal from the vehicle. The Beeps and Vibration are selectable (on/off). To enter program mode, 1. 2. 3. 4. Press VEH Button on the side of the remote control 5 times. The remote will beep and the AM or PM display will begin flashing. Press the Start button to choose the mode of “Beep ON/OFF & Vibrate ON/OFF”. Press the VEH Button to Save and Exit Setup or wait 8 seconds, the LCD light will turn off.
PAGE 6
1-WAY SIDEKICK The 1-Way sidekick remote adds flexibility to your system. You can have the convenience of operating your system without needing to carry the larger pager remote. The Sidekick remote has less range and offers all of the same operation features except for pageback confirmation. The 1-Way Sidekick Remote uses three CR-2016 Lithium 3 Volt Batteries. To replace the battery on Sidekick: Simply remove the two Phillips screws holding the back cover in place.
PAGE 7
STATUS LED STATUS LED: Used for Remote Start Diagnostics – page 14 (Optional, requires Installation of LED) LED will flash when locking your doors with remote. LED will remain solid in Valet Service Mode. REMOTE ENGINE CONTROL REMOTE START & TRUNK POP – Button Press Selection (Option # 6): To eliminate the possibility of accidentally opening the trunk or starting the vehicle, there are (3) options for button press selection.
PAGE 8
REMOTE ENGINE CONTROL REMOTE ENGINE STARTING – UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank time of up to 4 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 4 seconds to help prevent damage to the starter from over cranking.
PAGE 9
REMOTE ENGINE CONTROL IDLE DOWN MODE: This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle will remain running for the programmed time or until canceled. The Run Time choices are: 10, 20, 30 minutes or Infinity Run. Default = 20 minutes Examples: • You pull up to a convenience store for a quick stop, “Idle Down” mode keeps engine running when you exit the vehicle, (with keys in hand) remote lock doors.
PAGE 10
REMOTE ENGINE CONTROL SELECTABLE HOURLY COLD-START MODE (1-4 HOURS) This mode allows the vehicle to be programmed to self-start every 1, 2, 3 or 4 hours and run for the programmed run time. This can be helpful during extremely cold conditions where engine fluid freeze-up is a concern. TIMED SELF-START MODE – Exiting the Vehicle: 1) Engine should be running with the Key. Press the Remote Start button for at least 1 second. Lights will turn on signaling the remote start has turned on and doors will unlock.
PAGE 11
TURBO TIMER MODE (Option 22) The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1, 3 or 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cooldown without the need for expensive turbo timers. The Default = OFF. To Activate Turbo Timer: With the engine running by key, press Remote Start Button with brake pedal depressed.
PAGE 12
MANUAL TRANSMISSION MODE (Option 11) MANUAL TRANSMISSION EXIT PROCEDURE (Option #11-1 and 11-3) This system features a Manual Transmission Mode. When exiting the vehicle, there is a safety check out procedure required for the manual transmission mode to work. There are 2 choices of operation: 1. Option 11-1: With engine running and vehicle in neutral, set parking brake, then press “KEY” Icon on transmitter. The remote starter will turn on and take over operation of the vehicle. 2.
PAGE 13
CONVENIENCE AND SAFETY FEATURES AUTO LOCK / UNLOCK (Option # 2) The Auto Lock feature controls whether the doors will automatically lock/unlock on your vehicle when driving or with turning the Ignition ON/OFF. If the Auto Lock feature is turned on, and your system is in “Tach” mode, then the doors should automatically lock as the engine RPM’s increase (driving).
PAGE 14
CONVENIENCE AND SAFETY FEATURES VALET MODE Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into Valet Mode. The Remote Start function WILL NOT operate when in Valet Mode. 1. To Activate Valet Mode Manually: Turn the ignition on and press the Valet button [about 5-6 seconds] until the LED turns on solid. Repeat the process to exit VALET mode. 2.
PAGE 15
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The DS-7 learns up to 4 different transmitter codes. 1. Turn Ignition Key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. Press button #1 of the first transmitter.
PAGE 16
2-VEHICLE OPERATION & PROGRAMMING Your remotes have the ability to control a second vehicle with a Crimestopper system installed. To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter Programming” steps (Pg. 15) at the second vehicle and learn YOUR remote, along with vehicle #2’s existing remotes. 2-VEHCLE NOTES: (1) You do not have to switch between Vehicle “1” and “2” to get pages from each vehicle.
PAGE 17
NO FACTORY KEYLESS ENTRY AFTER REMOTE START Most new cars Do Not allow the factory Remote Keyless Entry to function with the Ignition ON. This means you can’t use the factory remote to lock or unlock the doors. After remote start you have to use the keys to unlock the door. Also, many new vehicles unlock the doors when disarming the factory alarm. This leaves the doors unlocked while Remote Started. To resolve this problem, have your installer connect the door locks to the Remote Start Keyless Entry.
PAGE 18
2-Way DATA PORT This system only works on vehicles with a CANBUS computer system and requires a Databus Module to integrate with the factory computer. Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. This Crimestopper system has a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module.
PAGE 19
PAGE 20
www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2012 Crimestopper Security Products ONLINE TECHNICAL SUPPORT www.crimestopper.