RS1-G5, RS3-G5, RS4-G5 RS7-G5 (2-Way Paging System) REMOTE START SYSTEM OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Cool Start™ Remote Engine Starter and Keyless Entry with DP Technology by Crimestopper Security Products Inc. This booklet contains the information necessary for operating your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….………………………………….…………….….…………2 Using the Remote Control (1, 4 and 5 button)….……………….……………………….………....………….....3-4 Using the 2-Way Pager……………………………………………….……………………….………....…………...5-6 Setting the Clock and Beep or Vibrate Selection…………………………………………………….……….….6-7 Status LED………………………………………………………………………………………………..……….….……8 Remote Engine Control…………….…..……………………………………………………………….…….…..…8-11 Turbo Timer Mode……………………………….……………………………………...……………….…………..….
USING THE REMOTE CONTROL VEH RS1-G5 RS3-G5 RS1-G5: The transmitter supplied with this system is a single button remote control. RS3-G5: The transmitter supplied with this system has 4 vertical buttons – Lock, Unlock, Vehicle Select and Start. To eliminate the possibility of accidentally starting the vehicle, there are (3) choices for button press selection. Option # 6 will allow you to change whether the Remote Starter is activated by a: 1. Double Press – 2 presses of Start button. 2.
USING THE 5 BUTTON REMOTE CONTROL FM 1-WAY AM 1-WAY VEH 1 = Green LED VEH 2 = Red LED VEH 1 = Blue LED VEH 2 = Red LED AUX Outputs thru Data AUX 1 = Trunk + Lock AUX 2 = Trunk + Unlock AUX 3 = Trunk + Start AUX 4 = Lock + Start ARM / LOCK DISARM / UNLOCK TRUNK START (Requires Canbus Data Module) VEH VEHICLE SELECT REMOTE VALET = LOCK + UNLOCK (4 seconds) Option 27 has 3 choices for Remote Valet. 1. Double Press. 2. 4 Second Press (Default). 3. OFF (no Remote Valet).
USING THE 2-WAY PAGER TRANSMITTER SIDE BUTTONS LCD SCREEN ICONS Valet Mode (Tools) Transmit Signal Battery Life Ignition ON Hood Open Lock/Unlock (Arm/Disarm) Silent no beeps Sensor Warning (Small Hammer) Sensor Trigger (Big Hammer) Door Open CLOCK / Run Count Down VEHICLE SELECT Trunk Open Remote Started LOCK / ARM TRUNK RELEASE UNLOCK / DISARM REMOTE START USB Charger (Under Side Cover) AUX Outputs thru Data Note: Some Icons on the LCD display only function on the Combo Alarm with Remote S
USING THE 2-WAY PAGER TRANSMITTER The 2-Way LCD Pager remote transceiver is used to send and receive information from the vehicle. The Control Module transmits High Frequency FM signals from the vehicle to your pager over long distances. Your range will vary depending on location, terrain, and local RF noise/interference. This system is not guaranteed to page you if you are behind concrete walls, underground, in a large structure, or in an area with high levels of electronic interference.
REMOTE BEEP & VIBRATE SELECTION The LCD pager remote BEEPS and VIBRATES when it receives a signal from the vehicle. The Beeps and Vibration are selectable (on/off). To enter program mode, 1. 2. 3. 4. Press VEH Button on the side of the remote control 5 times. The remote will beep and the AM or PM display will begin flashing. Press the Start button to choose the mode of “Beep ON/OFF & Vibrate ON/OFF”. Press the VEH Button to Save and Exit Setup or wait 8 seconds, the LCD light will turn off.
STATUS LED LED Operation: (Optional, requires Installation of LED) LED will flash when locking your doors with remote. LED will remain solid in Valet Service Mode. REMOTE ENGINE CONTROL REMOTE START Button Press Selection (Option # 6): To eliminate the possibility of accidentally starting the vehicle, there are (3) options for button press selection. This option allows you to change whether the Remote starter is activated by a: 4. Double button - ½ second presses. 5. *Single ½ second press (Default). 6.
REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank time of up to 4 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 4 seconds to help prevent damage to the starter from over cranking.
REMOTE ENGINE CONTROL IDLE DOWN MODE: This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle will remain running for the programmed time or until canceled. The Run Time choices are: 10, 20, 30 minutes or Infinity Run. Default = 20 minutes Examples: • You pull up to a convenience store for a quick stop, “Idle Down” mode keeps engine running when you exit the vehicle, (with keys in hand) remote lock doors.
REMOTE ENGINE CONTROL SELECTABLE HOURLY COLD-START MODE (1-4 HOURS) This mode allows the vehicle to be programmed to self-start every 1, 2, 3 or 4 hours and run for the programmed run time. This can be helpful during extremely cold conditions where engine fluid freeze-up is a concern. TIMED SELF-START MODE – Exiting the Vehicle: 1) Engine should be running with the Key. Press the Remote Start button for at least 1 second. Lights will turn on signaling the remote start has turned on and doors will unlock.
TURBO TIMER MODE (OPTION #22) The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1, 3 or 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cooldown without the need for expensive turbo timers. The Default = OFF. To Activate Turbo Timer: With the engine running by key, press Remote Start Button with brake pedal depressed.
MANUAL TRANSMISSION MODE (Option 11) MANUAL TRANSMISSION EXIT PROCEDURE (Option #11-1, 11-3 & 11-4) This system features a Manual Transmission Mode. When exiting the vehicle, there is safety check out procedure required for the manual transmission mode to work. There are 3 choices of operation, 1. Option 11-1: With engine running and vehicle in neutral, set parking brake, then press “KEY” Icon on transmitter. The remote starter will turn on and take over operation of the vehicle.
CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (Power Door Locks, may require Data Module - Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. Parking lights will flash once for Lock and twice for Unlock.
CONVENIENCE AND SAFETY FEATURES REMOTE TRUNK RELEASE OR DOMELIGHT ILLUMINATION (Option 9) This system includes an output that can be programmed to remotely release a factory electronic trunk or illuminate the interior light when you unlock your vehicle for lighted entry at night. If you have the optional trunk pop installed, simply press and release the Trunk Button #3 on the transmitter to remotely open trunk.
TRANSMITTER PROGRAMMING on 1 BUTTON Note: All transmitter codes must be learned at time of programming!! The RS1-G5 learns up to 4 different transmitter codes. 1. Turn Ignition Key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. Press the start button of the first transmitter.
TRANSMITTER PROGRAMMING on 4 & 5 BUTTON Note: All transmitter codes must be learned at time of programming!! The Cool Start system learns up to 4 different transmitter codes. 4. Turn ignition key to the ON position. 5. Press Programming button 4 times, after a few seconds the unit flashes the parking lights 4 times. 6. Press Lock button of the first transmitter.
2 VEHICLE OPERATION Your remotes have the ability to control a second vehicle with a Crimestopper system installed. To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter Programming” steps (Pg. 15) at the second vehicle and learn YOUR remote, along with vehicle #2’s existing remotes. 2-VEHCLE NOTES: (1) You do not have to switch between Vehicle “1” and “2” to get pages from each vehicle.
NO FACTORY KEYLESS ENTRY AFTER REMOTE START Most new cars Do Not allow the factory Remote Keyless Entry to function with the Ignition ON. This means you can’t use the factory remote to lock or unlock the doors. After remote start you have to use the keys to unlock the door. Also, many new vehicles unlock the doors when disarming the factory alarm. This leaves the doors unlocked while Remote Started. To resolve this problem, have your installer connect the door locks to the Remote Start Keyless Entry.
2-Way DATA PORT Some vehicles require a Databus Module to Bypass the factory Immobilizer and operate the keyless entry Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. Crimestopper Systems with DP Series have a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module.
BATTERY REPLACEMENT on 1 BUTTON REMOTE To replace the battery: Simply remove the screw on back of the transmitter and slide the case apart as shown. Remove the two CR-1620 Lithium batteries and replace. Put case back together and tighten screw.
BATTERY REPLACEMENT on 4 BUTTON REMOTE To Replace the Battery: The Remote Control uses two CR-2025 Lithium 3 Volt Batteries. Simply remove the Phillips screw located behind key ring (see diagram below). Use a small screw driver as shown in Figure 2 to remove the back cover. Slide old batteries out. Insert the new batteries into plastic cover and slide into place with the (+) end facing up. The plastic cover keeps the batteries from shorting out against the side of metal housing.
BATTERY REPLACEMENT on 5 BUTTON REMOTE To Replace the Battery: The Remote Control uses two CR-2025 Lithium 3 Volt Batteries. Simply remove the Phillips screw located behind key ring (see diagram below). Use a small screw driver as shown in Figure 2 to remove the back cover. Slide old batteries out. Insert the new batteries into plastic cover and slide into place with the (+) end facing up. The plastic cover keeps the batteries from shorting out against the side of metal housing.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.