User's Manual

ManualsBrandsSTEELMATE ManualsElectronicsAntenna

DS-1 / DS-3 / DS-4 (1-Way)

DS-7 (2-Way Paging)

DS-00 (ADD-ON MODULE)

DATA START SYSTEMS

INSTALLATION INSTRUCTIONS

CONGRATULATIONS on your choice of a Data Start™ Remote Engine Starter and Keyless Entry with Data Port

Technology by Crimestopper Security Products Inc. This system is designed to be used in conjunction with a Databus

Bypass Module and WILL NOT work by itself as a stand alone remote starter. This booklet contains the information

necessary for installing your system.

Note: Some features will not be available on units with 1 button, 3 button, and 4 button remotes.

DISCLAIMER:

This installation book is designed for the installer or individual with an existing understanding of automotive electrical

systems, along with the ability to test and connect wires for proper operation. To ease installation, we suggest that you

READ THIS MANUAL before beginning your installation. This book is provided as a GENERAL GUIDELINE and the

information contained herein may differ from your vehicle. Crimestopper Security Products, Inc. and its’ vendors shall not

be liable for any accident resulting from the use of this product. This system is designed to be professionally installed into

a vehicle in which all systems and associated components are in perfect working condition.

TECHNICAL SUPPORT: (800) 998-6880

Monday - Friday 8:00am - 4:30pm Pacific Std. Time

Web Site: www.crimestopper.com

E-mail: tech-support@crimestopper.com

CRIMESTOPPER SECURITY PRODUCTS, INC.

1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV 08-2012

This device complies with FCC Rules part 15. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference that

may be received, including interference that may cause undesired

operation. The manufacturer is not responsible for any radio or TV

interference caused by unauthorized modifications to this equipment.

Such modification could void the user’s authority to use the

equipment.

BTR039A

Summary of content (20 pages)

PAGE 1
DS-1 / DS-3 / DS-4 (1-Way) DS-7 (2-Way Paging) DS-00 (ADD-ON MODULE) BTR039A DATA START SYSTEMS INSTALLATION INSTRUCTIONS CONGRATULATIONS on your choice of a Data Start™ Remote Engine Starter and Keyless Entry with Data Port Technology by Crimestopper Security Products Inc. This system is designed to be used in conjunction with a Databus Bypass Module and WILL NOT work by itself as a stand alone remote starter. This booklet contains the information necessary for installing your system.
PAGE 2
TABLE OF CONTENTS Pre-Installation Considerations….………...……...………………………………………………………………..….………..2 Installation Cautions & Warnings………………………………………………………………………………..….....……..…3 5 Pin Power Plug……..…………………………………………………………………………………………....…………......3 Optional 8 Pin Plug...…………………………………….…………….……..…………...….…………..………….………..4-5 AUX Channel Output (Trunk release, Dome light or Horn honk)…..……………………………………………..…………5 Door Lock Diagrams………….……………………….…………………..…..…….…......………………………………….…6 Smart Tachless Mode…..………….
PAGE 3
INSTALLATION CAUTIONS & WARNINGS This System is a Low Current Remote Start that only works in Data Mode with a Bypass Module. DO NOT route any wiring that may become entangled with brake, gas pedals, steering column or any other moving parts in the vehicle. DO NOT exceed the rated output current of any circuit on the Remote start module. Failure to observe this warning will result in damage to the unit not covered under warranty.
PAGE 4
OPTIONAL 8 Pin Plug This plug is optional and may not be needed with many databus bypass modules. Check the databus guide for latest manual with wiring information before using this plug. These are optional features that may not be included with the bypass module. YELLOW BLACK OUTPUT: Ground Out when Running (-) 500 milliamp The Ground Out when Running is required by some bypass modules. This wire turns on when the remote start button is pressed and stays on through the duration of the remote start.
PAGE 5
AUX Output (Trunk Release – Dome Light – Horn Honk) BROWN: AUX OUTPUT (-) 500 milliamp This output is programmable for 3 modes of operation. See Programming Option #9 Section. 1. 30 second Dome Light output. 2. Momentary ½ second output (Default). 3. Horn Honk output. Note: Some vehicles like Lexus and Toyota require a 2 to 3 second output for the Trunk Pop to operate.
PAGE 6
DOOR LOCK DIAGRAMS NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN RED BLUE RED FUSED +12V + BLUE 85 86 87 87A 30 FACTORY POWER LOCKING RELAYS L UL 87 87A 30 FACTORY POWER LOCKING UL RELAYS AFTERMARKET MOTOR/DOOR LOCK WIRING GREEN GREEN FUSED +12V + RED BLUE 85 86 87 87A 30 85 85 86 86 87 87A 30 87 87A 30 CUT L FUSED +12V + RED BLUE MASTER SWITCH UL 86 L REVERSE POLARITY DOOR LOCK WIRING + 85 CUT 6 85 86 87 87A 30
PAGE 7
Status LED and Valet Switch PROGRAM OVERRIDE SWITCH: 2 PIN PLUG (REQUIRED FOR PROGRAMMING & LEARNING REMOTES) This is a multi-function switch used for programming options, transmitters, Valet mode. LED: 2 PIN PLUG The LED is used for Remote Start Diagnostics and a Valet indicator. It will also flash for use as security deterrent. VALET / PROGRAM SWITCH STATUS LED “SMART TACHLESS” MODE Your Data Start system includes a unique voltage monitor called “Smart Tachless” mode.
PAGE 8
TACH PROGRAMMING & TACH SIGNALS INTRODUCTION This system has 3 methods of monitoring the engine running. Option #1 controls how the system monitors the engine running. 1. Tach Reference Mode – Monitors Engine R.P.M. - Most reliable method, see Tach programming below. 2. Tachless Mode - Default. When vehicle is remote started, the battery voltage rate will go up because the Alternator starts working. The Tachless Mode is adjustable in 1% increments thru Option 21. 3. Not Used. 4.
PAGE 9
OPTION PROGRAMMING To Engage Option Programming: 1. Turn Ignition Key to the ON position. Do not start vehicle. 2. Press the Program / Valet button 5 times. Wait for the unit to flash the lights or park light LED flashes 5 times. 3. Push the valet program button the number of times that corresponds to the option number desired (1-26X). You must get a light flash after each button press. If the system did not flash the lights and, then it did not register your press. Press carefully and do not lose count. 4.
PAGE 10
Option # Option Description TX Button #1 TX Button #2 Default Value TX Button #3 TX Button #4 Lock after Remote Start / Arm OEM Alarm with Abort Lock / Arm OEM Alarm with Abort Horn Honk 8 Lock with Remote Start / Abort OFF *Lock after Remote Start* 9 Brown wire function Dome Light *Trunk pop* 10 Unlock before Remote Start (to Disarm OEM Alarm) ON *OFF* 11 Transmission Type (thru data) 12 Idle Down Timer Manual Transmission with Remote Control 10 Minutes *20 Minutes* 13 Horn Chir
PAGE 11
OPTION DESCRIPTIONS 1. Engine Monitoring: This option controls how the system monitors the engine running. You can program for Tachless mode that monitors battery voltage, Tach mode in which the unit uses a Tach signal (RPM) or for Timed Crank as an alternative. There are 4 choices for this option: 1. Engine R.P.M. (Tach) - Most reliable method. Tach must be programmed for this option to work. 2. Tachless Mode - Default.
PAGE 12
OPTION DESCRIPTIONS 4. PINK / WHITE WIRE SELECTION: This option controls the Pink / White wire function. 1. Pink / White = Accessory 2 2. Pink / White = Ignition 2 - Default. 3. Pink / White = Start 2 5. DATA PORT PROTOCOL: ADS iDatalink or EVO / SL Series This option controls the Data Port Protocol for ADS / OFA Series modules or EVO / SL Series modules. The default is set for EVO / SL Series Protocol. This option has no effect on conventional wiring of Bypass modules.
PAGE 13
OPTION DESCRIPTIONS 10. UNLOCK BEFORE REMOTE START: This option is used to disarm an OEM Alarm System before Remote Start. Default = OFF 11. TRANSMISSION TYPE: Requires Tach Mode Programmed This option selects automatic or manual transmission mode in Data Mode only 1. Manual Shift Transmission - Requires Remote Start Button pressed with Hand Brake Activated. 2. Automatic Transmission – Default. 3. Manual Shift Transmission – Starts Exit procedure with Hand Brake Set and engine running. 12.
PAGE 14
OPTION DESCRIPTIONS 18. MINIMUN STARTER CRANK TIME: Default = 0.8 seconds This option controls the Minimum Starter Cranking time. This does not affect maximum crank time. This can be adjusted in 0.1 second increments Up or Down from 0.5 to 4 seconds. The starter can still crank up to 4 seconds with a 0.8 setting, depending on Tach or Tachless setting. TIMED START, use Hybrid Mode (option 1-4) with this option to set a fixed crank time.
PAGE 15
OPTION DESCRIPTIONS 26. OPTION RESET: (RESTORE TO DEFAULT) This option restores all programmable options 1 thru 23 to factory default. The unit will flash the lights 2 times and all values will be reset to factory original settings. Resetting the option table to default does not change the type of antenna system. ANTENNA DIAGRAM Antenna should be located at top of widow at least one inch away from metal surface.
PAGE 16
TRANSMITTER PROGRAMMING Transmitter Programming: Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system’s remote codes must be learned at time of programming!! These systems allow storage of up to 4 different remote codes in memory. 1. Turn Ignition Key to the ON position. (Do not start vehicle). 2. Press Program/Valet button 4 times. Wait for the unit to flash the parking lights and park light LED flashes exactly 4 times. 3.
PAGE 17
MANUAL TRANSMISSION MODE MANUAL TRANSMISSION INSTALLATION: This option requires a databus module with hand brake and door status feature. The Door and Hand Brake Status only work thru Data Mode. OPTION 11 - TRANSMISSION TYPE: Manual Transmission Requires Tach programmed to operate. This option selects automatic or manual transmission mode - 3 Choices of operation. 1. Manual Shift Transmission - Requires Remote Start Button pressed with (-) Hand Brake set. 2. Automatic Transmission – Default. 3.
PAGE 18
DATA START Wiring Diagram ANTENNA OVERRIDE/ PROGRAM BUTTON 1-Way or 2-Way Option # 25 STATUS LED Park Light LED DATA PORTS Fortin This unit is designed to work in conjunction with a Databus Module ADS iDataLink (+) Brake Switch Purple Optional Gray (-) Hood Switch (-) Aux Output (-) OEM Disarm (-) OEM Arm (-) Unlock (-) Lock Red OPTION # 4 Selectable Pink/white Pink Orange/Black (-) 500mA Blue (-) 500mA Green (-) 500mA 12 Volts Power Source Black Ground OPTION # 9 Brown (-) 500mA Trunk R
PAGE 19
DATA PORT This unit requires a Databus Module for Remote Start. There are 2 types of Protocol, ADS iDatalink and EVO SL series modules. The default is set for EVO SL series Protocol. Please refer to Databus module manual for detail instructions. The Data Port Protocol must be programmed for the correct module.
PAGE 20
REMOTE START DIAGNOSTICS If the system flashes the LED and Parking Lights one to seven times and doesn’t attempt remote. The LED will continue to flashing the error code until the ignition is turned on, it means the following: 1 Parking Light Flash (1 LED Flash) = Problem with Brake Switch. 2 Parking Light Flashes (2 LED Flashes) = Problem with Hood Switch. 3 Parking Light Flashes (Solid LED) = Valet Service Mode. 5 Parking Light Flashes (5 LED Flashes) = Ignition On before Remote Start or Tach problem.