Digital Fabric Steam Press Owner’s Guide Guía Del Propietario De La Plancha A Vapor Digital Para Telas Guide D’utilisation – Presse À Vapeur Numérique Pour Tissu MODEL SF-680 MODELO SF-680 MODÉLE SF-680 ENGLISH p. 2 ESPAÑOL p. 14 FRANÇAIS p.
IMPORTANT SAFETY INSTRUCTIONS This owner's guide and any additional inserts are considered part of the product. They contain important information about safety, use, and disposal. Before using the product, please familiarize yourself with all operating and safety instructions. Please keep all documents for future reference and pass these documents on, together with the product, to any future owner. See our website for the most current version of this owner’s guide.
rated for less amperage may overheat. Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over. 13. This GARMENT STEAMER is for use with a 120 volt electrical outlet. The cord has a plug as shown at A in Figure 65.1. An adapter, as shown at C, can be used to connect threeblade grounding-type plugs to two-slot receptacles (it is not included with your product).
Product Information The following features and accessories are included with your steam press. Carefully inspect packaging material as some parts are shipped inside Styrofoam packaging. To obtain possible missing parts, refer to the Consumer Support section on page 10 of this manual.
• The Handle (1) is used to safely lift up and lower the Pressing Plate, and to carry the unit. • The Steam Burst Buttons (2) are located on either side of the Handle, and produce a powerful burst of steam when pressed. • The Water Reservoir Cap (3a) covers the Water Reservoir fill hole and must be removed in order to fill the Water Reservoir with distilled water. • The Water Reservoir (3b) is the tank in which distilled water is stored for use by the unit.
Using Your Digital Fabric Steam Press FILLING WATER RESERVOIR 1. Place Digital Fabric Steam Press on a flat, level surface. 2. Turn Locking Knob to “Unlock” position to unlock Pressing Plate. 3. Lift up Pressing Plate using Handle. It will automatically stay in lifted position. 4. Pull Water Reservoir out. Note that Water Reservoir cannot be completely removed from unit; do not attempt to force it free. 5. Remove Water Reservoir Cap to expose Water Reservoir fill hole. 6.
STEAM BURST 1. Hold Pressing Plate approximately 3 in. (75 mm.) above Ironing Board. 2. Press Steam Burst Button to release a burst of steam onto fabric for 2-3 seconds. 3. Lower Pressing Plate onto fabric for 8-10 seconds, then raise once again. Note: If press is left on fabric for more than 10 seconds, it could result in damage to fabric. 4. Repeat steps 1-3 above until fabric is smooth and wrinkle-free. PRESSING AND STEAMING TIPS Pressing Shirts and Blouses 1.
Storage & Care AUTO SHUT-OFF The Auto Shut-Off feature of the Digital Fabric Steam Press includes both an Auto Shut-Off and an Auto Wake-Up. These multiple function safety features deactivate electrical power to the heater when the Pressing Plate has been left in closed position against the Ironing Board for more than 10 seconds. Heater deactivation is signaled by a beeping sound. Heater functionality is restored when the Pressing Plate is lifted back up.
Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION Unit fails to heat up. Power Indicator Light DOES NOT illuminate. Unit is not plugged in. Plug power cord into electrical outlet. Household circuit breaker / ground fault interrupter has tripped or blown a fuse. Reset circuit breaker / ground fault interrupter, or replace fuse. If you need assistance, contact a licensed electrician. Unit heats up, but fails to steam. Power Indicator Light does illuminate. Auto Shut-Off has engaged.
Product Support CONSUMER SERVICES For problems with your Digital Fabric Steam Press, please refer to the troubleshooting guide located on Page 9 of this manual. Additional inquiries should be directed to our consumer support services through our Web site, www.steamfast.com. If you do not have internet access, you may also contact our Consumer Service Department by telephone, at 1-800-711-6617.
ACCESSORIES & PARTS When ordering accessories and parts for your Digital Fabric Steam Press, you may refer to the part numbers below. Replacement parts may be ordered through our Web site: www.steamfast.com You may also contact Consumer Service directly: consumerservice@steamfast.
Warranty Information 1-YEAR LIMITED WARRANTY What is covered Steamfast, a division of Vornado Air, LLC (“Steamfast”).
• THIS WARRANTY GIVES BUYER SPECIFIC LEGAL RIGHTS. BUYER MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE-TO-STATE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, AND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO BUYER. How do you register the Warranty Buyer must complete an application to register this Warranty within sixty (60) days following date of purchase.
review this product online evalúe este producto en línea évaluer ce produit en ligne www.steamfast.com/reviews Steamfast 1-800-711-6617 415 East 13th, Andover, KS 67002 www.steamfast.com consumerservice@steamfast.