Installation Guide

ManualsBrandsStealthLock ManualsPadlocksKeyless Cabinet Locking System Strike Plate

StealthLock

, Keyless Invisible Security

Instruction Manual

StealthLock

, Keyless Invisible Security

Thank you for purchasing StealthLock

. StealthLock

is an innovative solution for

keyless invisible security. Using radio frequency technology, StealthLock

allows you to

secure almost any wood cabinet door or drawer with little or no changes to the cabinet

design.

StealthLock

is battery operated and works with a user established 4 to 8 digit code.

Operation is simple: input your code and press lock or unlock. The Latch can operate any

Receiver Latch within a 15 foot range which allows it to be placed anywhere, leaving no

trace of visible hardware. In addition, the Latch can operate multiple Receiver Latches to

secure an entire room or bank of cabinets.

StealthLock

is designed to install and program easily and offers:

Programmable user and supervisor codes

Programmable modes of operation

Programmable reset features

StealthLock

is recommended for use on cabinets made from:

Wood

Wood products

Phenolic resin

Glass

StealthLock

is NOT intended for:

Metal furnishings or cabinets

Exterior furnishings or cabinets

Applications where temperatures fall below 50° F or above 120° F

StealthLock

may be used in households to help protect minors from unsafe materials.

It is strongly recommended that all batteries used by the StealthLock

be replaced on an

annual basis. Please mark this date on your calendars to insure replacement. In the event

you have allowed the batteries to die, you will need to forcefully enter the cabinet. The

StealthLock

strike plate is designed to shear away at 80lbs of force. A new strike plate

will then be needed to operate the lock.

Summary of content (10 pages)

PAGE 1
Instruction Manual Thank you for purchasing StealthLock®. StealthLock® is an innovative solution for keyless invisible security. Using radio frequency technology, StealthLock® allows you to secure almost any wood cabinet door or drawer with little or no changes to the cabinet design. StealthLock® is battery operated and works with a user established 4 to 8 digit code. Operation is simple: input your code and press lock or unlock.
PAGE 2
SL-100 StealthLock® Contents Battery Installation – Receiver Latch The Receiver Latch uses 4 AAA batteries that are expected to last 2 years in normal operation (4 open/close cycles per day). 6.785 1 – RL-100 Receiver Latch Screws Included Batteries should be replaced on an annual basis to insure continued reliability. 2.500 The LED will begin to blink after 5,500 operations to warn that batteries need to be replaced 2.
PAGE 3
Battery Installation - Transmitter Pad Installation Instructions – Receiver Latch The Transmitter Pad uses a CR2032 battery that is expected to last 2 years in normal operation (4 open/close cycles per day). Batteries should be replaced on an annual basis to insure continued reliability. During initial installation, remove the red ribbon to activate the installed battery The StealthLock® is designed to operate within non-metallic cabinetry.
PAGE 4
Step #3 – Press the learn button on the Receiver Latch until the yellow LED lights to insure that the Latch is in the open position Installation Instructions – Transmitter Pad Learn Button The Transmitter Pad has a functional range of 15 feet from the Receiver Latch and can be mounted virtually anywhere on any non-metallic panel. To mount, simply remove the release paper from the tape on the back side of the Transmitter Pad, and press into place.
PAGE 5
Programming – Introduction Programming – Introduction StealthLock® is very easy to use and operate. Once installed, the user enters the user TP-100 Transmitter Pad code (factory default 0000) and presses Lock Lock Button to lock the cabinet. To unlock the cabinet, the user enters the user code and presses Unlock and the cabinet will open. Green LED Indicator ® StealthLock is fully programmable allowing the user or supervisor the ability to change codes, modes, and restore lock settings.
PAGE 6
Programming the User Code Programming the Supervisor Code Use these steps to change your current user code. The factory default code is 0000. User codes must be 4 to 8 digits in length. To view a video of these steps, go to www.StealthLock.com Note that the user code can not be changed if the Receiver Latch has been set to Single Use Mode. Use these steps to change the current supervisor code.
PAGE 7
StealthLock® features several modes of operation and reset ability. These functions can be changed using the following instructions by users who have rights to the supervisor code. Modes and reset can only be modified with knowledge of the supervisor code. Programming Single Use Mode / Non Single Mode Non Single Mode allows the user to set the user code to be used by a single person only.
PAGE 8
Programming Learn Disable / Learn Enable Reset Factory Default Settings Learn Disable / Learn Enable Mode allows the supervisor to either allow or not allow a user to program a new user code. In Learn Disable Mode, only the users with knowledge of the supervisor code can make any programming changes. This feature returns the lock to its original factory settings. This will place the Receiver Latch into a Non Single Use Mode, Passage Mode, and Learn Enable Mode.
PAGE 9
Clear User Pin Code Auxiliary Power This feature returns the user code back the factory default setting of 0000. It does not reset any other mode or feature of the lock. If desired, the StealthLock® Receiver Latch may be connected to 120 VAC power using the optional RL-AP1 Power Supply There is a 60 second programming time limit to each step. If you time out or make an error, programming will end and you will need to restart from step 1. 1.
PAGE 10
Transmitter Pad Mounting Accessories Regulatory Information The user is cautioned that changes or modifications not expressly approved by CompX Timberline could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.