Articulating Dual-Monitor Stand - Aluminum *actual product may vary from photos User Manual SKU#: ARMDUALSS For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards. Mesures de Sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. • Make sure that the weight of the monitors doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the equipment. This product can support the following weight: 17.6 lb. (8 kg) per monitor mount. • Never operate this product if parts are missing or damaged.
Dichiarazioni di Avvertenza • Assemblare il prodotto rispettando le istruzioni. Il mancato rispetto delle istruzioni potrebbe causare danni a persone o proprietà. • Verificare che il peso del monitor non superi la capacità di supporto del prodotto. In caso di superamento della capacità di supporto potrebbero verificarsi danni a persone o apparecchiature. Il prodotto è in grado di supportare i seguenti pesi: 8 kg per monitor. • Non utilizzare il prodotto in presenza di parti mancanti o danneggiate.
注意 • 必ず取扱説明書に従って本製品の組み立てを行って下さい。取り扱いを誤 った場合に、傷害を負う恐れや物的損害が発生する恐れがあります。 • 取り付けるモニターの重量が、本製品で定められた最大積載重量を超えな いようにして下さい。最大積載重量をオーバーした場合、傷害を負う恐れや モニターや本製品に損害が発生する恐れがあります。本製品は、モニター1 台あたり8 kgまで支持できます。 • 本製品で使用している部品の一部が紛失していたり損傷している状態で使 用するのは絶対に止めて下さい。 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Table of Contents Compliance Statements.........................................................................i Safety Statements...................................................................................ii Warning Statements...............................................................................iii Product Information...............................................................................1 Package Contents..............................................................................
Product Information Package Contents Swivel Arms Pole Base Shoulder Qty: Two Qty: One Qty: One Qty: One Screws: Screws: M4x12 mm M5x12 mm M4x16 mm M5x16 mm CableManagement Clips VESA Mounts M4x20 mm M5x20 mm Qty: One Qty: Two Qty: Eight of each Qty: Eight of each 3 mm Hex Key Washers Spacers Qty: Eight Qty: Sixteen 1 6 mm Hex Key User Manual Qty: One of each Qty: One
Product Diagram Dimensions To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Front View 1 2 2 1 3 4 1 VESA Mounts 2 Swivel Arms 3 Pole 4 Base To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Rear View 5 6 5 Shoulder 6 Cable-Management Clip To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Side View 7 7 Height-Adjustment Lever To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Technical Specifications Type of Measurement Measurement VESA Mounting Hole Pattern 75x75 100x100 Weight Capacity Up to 17.6 lb. (8 kg) Per Monitor kg Tilt +900 to -400 Maximum Screen Size 32” (813 mm) Rotate +1800 to -1800 Swivel +900 to -900 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Requirements For the latest requirements, please visit www.StarTech.com/ARMDUALSS. • Two Monitors Note: Both Monitors must conform to the size, weight, and VESA pattern requirements (see Technical Specifications). • Phillips Head Screwdriver • (Optional) Two People for Installation To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Assembly Warning! Make sure that all of the hardware is assembled securely and checked for stability before you load the Monitors. Warning! Make sure that the weight of the Monitors does not exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. Assemble the Base 1. Loosen the Hex Screws that are located on the Base using the 3 mm Hex Key. 2. Slide the Cable-Management Clip onto the Pole. 3.
Figure 1 Collar Pole 3 mm Hex Key Cable-Management Clip Base Adjust the Collar 1. Loosen the Flat-Head Screws on the Collar, using the 3 mm Hex Key with Screwdriver Tip. 2. Slide the Collar up or down the Pole so that it sits at the desired height for your Monitors. 3. Tighten the two Flat-Head Screws that are located on the Collar, using the 3 mm Hex Key with Screwdriver Tip. (Figure 2) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Figure 2 Attach the Shoulder 1. 2. 3. Rotate the Lever on the Shoulder counterclockwise to loosen the Shoulder. Note: The Lever has a ratchet feature. Freely rotate the Lever by pulling it away from the Shoulder and rotating it to the desired position. Slide the Shoulder over and down the Pole, until it makes contact with the Collar. Rotate the Lever on the Shoulder clockwise to tighten the Shoulder. (Figure 3) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Figure 3 Shoulder Attach the Swivel Arms 1. Insert the Swivel Arms into the Sockets of the Shoulder until each Swivel Arm clicks into place. (Figure 4) To remove the Swivel Arms: Release the Clip that is located on the bottom of the Swivel Arms, where the Swivel Arms connect to the Shoulder, and pull upwards. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Figure 4 Swivel Arm To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attach the VESA Mounts to the Monitors ARMDUALSS is designed to be used with Monitors that are the same size and weight. If you attach Monitors that are different sizes and weights to ARMDUALSS, you do so at your own risk. To accommodate different Monitor designs, ARMDUALSS comes with six sets of Screws that are different lengths and diameters.
Figure 5 VESA Mount 4. (Optional) Place one or more Spacers between the Holes in the Monitor and the VESA Mount, to ensure it is flat against the Monitor. (Figure 6) Figure 6 Screw Washer 5. Spacers Use a Phillips Head Screwdriver to tighten the Screws. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Warning! Do not over-tighten the Screws. If you encounter resistance while you’re tightening the Screws, stop tightening. Failure to do so could result in damage to the Monitor. 6. Complete steps 1 to 4 to add a VESA Mount to a second Monitor. Attach the VESA Mounts to the Swivel Arms Note: A second person may be required to complete the following steps. 1. Lift the Monitor that will be positioned on the left-hand side and position it over the Swivel Arm Receptacle. 2.
Adjusting the Monitors Warning! The most stable configuration of ARMDUALSS is the “flat” position, with both of the Swivel Arms positioned in a straight line. ARMDUALSS can become unstable depending on how you position the Monitors. If you adjust the position of the Monitors, you should exercise caution and test the stability of ARMDUALSS before you use it in the adjusted configuration.
Figure 8 6 mm Hex Key Swivel Adjustment The Monitors can be adjusted on a 90-degree swivel. • Place both of your hands on either side of the Monitor and apply light pressure either left or right. Micro Height Adjustment 1. Insert the 6 mm Hex Key into the Height-Adjustment Lever that is located on the top of the VESA Mounts. 2. Turn the 6 mm Hex Key, or the Height-Adjustment Lever, clockwise to raise the Monitors or counterclockwise to lower the Monitors.
Figure 3. 9 Height-Adjustment Lever Cable Management The Power and Video Cables from your Monitors can be organized and contained within the Swivel Arms and alongside the Pole. To manage the Cables running to your Monitors, complete the following steps: 1. Connect the Power and Video Cables to each Monitor. 2. Route the Cables for the Monitor along the bottom of the Swivel Arm on the left-hand side. 3.
Note: If the Cables do not readily snap into the Cable- Management Channels, gently pull back one side of the Cable-Management Channel and feed the Cables into the Channel. Figure 10 Cable-Management Channel 4. Route the Cables along the Pole, through the CableManagement Clip, and towards the Video Source and Power Source. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Warranty Information This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
