Desk Mount Dual Monitor Arm | Crossbar Design | Articulating Actual product may vary from photos User Manual SKU#: ARMDUAL2 For the latest information and specifications visit www.startech.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question.
Warning Statements • Make sure that you assemble this product according to the instructions. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. This product can support the following weight: 35.2 lb. (2 x 8 kg). • This product is intended for indoor use only and should not be used outdoors. Varningsmeddelanden • Se till att du monterar produkten i enlighet med instruktionerna. • Överskrid inte produktens viktkapacitet.
Mensagens de aviso • Certifique-se de que monta este produto de acordo com as instruções. • Não exceda a capacidade de peso deste produto. Sobrecarregar este produto pode resultar em ferimentos ou danos de propriedade. Este produto pode suportar o seguinte peso: 2 x 8 kg. • Este produto destina-se apenas a uma utilização no interior e não deve ser utilizado no exterior. Advertencias de uso • Asegúrese de ensamblar este producto según las instrucciones.
Table of Contents Warning Statements...............................................................................2 Product Diagram.....................................................................................5 Product Dimensions...............................................................................6 Product Information...............................................................................7 Package Contents..............................................................................
Product Diagram 1 2 3 4 5 6 1 Swivel Arm Assembly 5 C- Clamp 2 VESA Mount x 2 6 Grommet 3 Pole 4 Cable Management Clips To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents VESA Mounts Swivel Arm Assembly Qty: Two Qty: One C-Clamp Assembly Pole Qty: One Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Pole Cap Cable Management Clip Qty: One Qty: Two Grommet Base Plate Micro-Adjustment Knobs Qty: One Qty: Two Micro-Adjustment Knob Screws Rubber Pads Qty: Two Qty: Five To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Pole Assembly Screw Grommet Plate Qty: Three Qty: One 4 mm Hex Key 6 mm Hex Key Qty: One Qty: One M4 x 12 mm Screws M4 x 16 mm Screws Qty: Eight Qty: Eight To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
M5 x 12 mm Screws M5 x 16 mm Screws Qty: Eight Qty: Eight Washers Spacers Qty: Eight Qty: Sixteen Swivel Arm Cable Clip 3 mm Hex Key Qty: Four Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Specifications 75 x 75 100 x 100 VESA LB kg 35.2 lb. (2 x 8 kg) Total Weight (two monitors) Max. 32 “ Screen Size 360o Rotation To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
- 450 to +450 Tilt - 900 to +900 Swivel Requirements • • • Phillips Head Screwdriver x 1 Monitors x 2 Mounting Surface x 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Mounting the Monitor Arm Using the C-Clamp 1. Insert the Pole Cap into the top of the Pole. Installing the Pole Cap 2. Slide the Cable Management Clips onto of the pole. - or Clip the Cable Management Clip onto the Pole. Installing Cable Management Clip 3. Align the three Screw Holes on the top of the C-Clamp with the three Screw Holes on the bottom of the Pole. 4.
5. Using the 4 mm Hex Key, tighten the three Pole Assembly Screws. Being careful not to over-tighten the Pole Assembly Screws. 6. Remove the backing from the Rubber Pads (x 5). 7. Apply the adhesive side of the Rubber Pads to the under side of the top of the C-Clamp. Attaching the C-Clamp to the Pole 8. While supporting the weight of the Monitor Arm, slide the C-Clamp over the edge of the Mounting Surface. 9.
10. Using the 3 mm Hex Key, loosen the Adjustment Screw on the Collar. 11. Position the Collar at the height you want the Monitors to sit. 12. Using the 3 mm Hex Key, tighten the Adjustment Screw on the side of the Collar, securing the Collar to the Pole. 13. Clip the Arm Assembly Clips (x 4) into place along the Swivel Arm Assembly. Installing the Arm Assembly Clips 14. Slide the Swivel Arm Assembly over-top of the Pole, until the Swivel Arm Assembly comes in contact with the Collar.
Installing the Swivel Arm Assembly 15. While holding the weight of the Swivel Arm Assembly, use the 6 mm Hex Key to tighten the Adjustment Screw on the Swivel Arm Assembly to secure the Swivel Arm Assembly in place. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Tightening the Swivel Arm Using the Grommet Mount 1. Insert the Pole Cap into the top of the Pole. Installing the Pole Cap To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
2. Slide the Cable Management Clips onto of the pole. - or Clip the Cable Management Clip onto the Pole. Installing Cable Management Clip 3. Align the three Screw Holes on the top of the C-Clamp with the three Screw Holes on the bottom of the Pole. 4. Using a Phillips Head Screw Driver, remove the small screw attached to the Knob onto the C-Clamp. Removing the Knob 5. Remove the backing from the Rubber Pads (x 5). To view manuals, videos, drivers, downloads, technical drawings, and more visit www.
6. Apply the adhesive side of the Rubber Pads to the side of the Grommet Base Plate without the protrusion. 7. Align the Protrusion on the Grommet Base Plate with the Notch on the bottom of the Pole. Aligning the Grommet Base Plate 8. Insert the Protrusion on the Grommet Base Plate into the Notch on the bottom of the Pole. 9. While holding the Grommet Base Plate against the bottom of the Pole, align the center hole on the Grommet Base Plate with the Grommet Hole in the Mounting Surface. 10.
Installing the Grommet 12. Tighten the Knob, until the Grommet Plate and Knob are pushing tightly against the bottom of the Mounting Surface. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Tightening the Knob 13. Using the 3 mm Hex Key, loosen the Adjustment Screw on the Collar. 14. Position the Collar at the height you want the Monitors to sit. 15. Using the 3 mm Hex Key, tighten the Adjustment Screw on the side of the Collar, securing the Collar to the Pole. 16. Clip the Arm Assembly Clips (x 4) into place along the Swivel Arm Assembly. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installing the Arm Assembly Clips 17. Slide the Swivel Arm Assembly over-top of the Pole, until the Swivel Arm Assembly comes in contact with the Collar. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installing the Swivel Arm Assembly 18. While holding the weight of the Swivel Arm Assembly, use the 6 mm Hex Key to tighten the Adjustment Screw on the Swivel Arm Assembly to secure the Swivel Arm Assembly in place. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Tightening the Swivel Arm Attaching the Monitors (Flush) Note: It is recommend that two people are used to mount the Monitors to the Monitor Mounts. 1. Determine the size and length of screw to use to mount the Monitors to the Monitor Mounts (M4 x 12 mm or M5 x 12 mm, if appropriate). To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
2. Lay the Monitor face down on a flat, level surface. 3. Align the Mounting Holes on the VESA Mount with the Screw Holes on the back of the Monitor, making sure that the Mounting Flange on the VESA Mount is at the top. 4. Align the Washers (x 4) with the Mounting Holes on the VESA Mount. 5. Insert the Screws (x 4) through the Washers and Mounting Holes and into the Screw Holes in the back of the Monitor. Installing the VESA Mount 6.
Note: Do not over-tighten the Screws. If you encounter resistance while you’re tightening the Screws, stop tightening. Failure to do so could result in damage to the monitor. 7. Repeat steps 1 - 6 to mount the second Monitor. Attaching the Monitors (Recessed) Note: It is recommend that two people are used to mount the Monitors to the Monitor Mounts. 1. Determine the size and length of screw to use to mount the Monitors to the Monitor Mounts (M4 x 12 mm or M5 x 12 mm, if appropriate). 2.
Installing the VESA Mount 7. Using a Phillips Head Screwdriver (sold separately) tighten the Screws, being careful not to over-tighten. Note: Do not over-tighten the Screws. If you encounter resistance while you’re tightening the Screws, stop tightening. Failure to do so could result in damage to the monitor. 8. Repeat steps 1 - 6 to mount the second Monitor. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Mounting the Monitors 1. While supporting the weight of the Monitor, slide the VESA Mount down onto the Swivel Arm Assembly, aligning the hole on the Mounting Flange (located on the VESA Mount) with the Micro-Adjustment Screw Protrusion on the Monitor Holder. Installing the Monitors 2. When the Mounting Flange on the VESA Mount is sitting on the Micro-Adjustment Screw Protrusion, mount the Micro-Adjustment Knob on the top of the MicroAdjustment Screw Protrusion. 3.
4. Using a Phillips Head Screwdriver, tighten the MicroAdjustment Screw. Installing the Micro-Adjustment Knob 5. Adjust the Monitor tilt until it is in the desired position. 6. Using the 6 mm Hex Key, tighten the Adjustment Screw on the side of the Monitor Holder, securing the Monitor in place. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Tightening the Monitor Adjustment Screw 7. Repeat steps 1 - 6 to mount the second Monitor. Adjusting the Monitors Tilt Adjustment 1. Using the 6 mm Hex Key, loosen the Adjustment Screw that is located on the side of the Monitor Mount. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjusting the Monitor Tilt 2. Adjust the tilt of the Monitor. 3. Once the Monitor is in the desired position, tighten the Adjustment Screw, securing the Monitor in place. Micro Adjustments Making micro adjustments will slightly move the monitor up and down. • Insert the 6 mm Hex Key into the center- top of the MicroAdjustment Knob and turn the Hex Key clockwise or counter-clockwise to just the Monitor up and down. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.
Making Micro Adjustments To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Routing the Cables • Monitor Cables can be routed along the Swivel Arm Assembly through the Cable Management Clips along the Swivel Arm Assembly and down along the Pole through the Cable Management Clip. Routing Cables • Once the Monitor Arm is assembled the Hex Keys can be placed in the front of the Cable Management Clip on the Pole. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Hex Key Holder To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Warranty Information This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
