MovingMedia® 2000 . iCell CDMA2000 1X iPA 1900 MHz Translating Bi-directional Amplifier BASIC INSTALLATION GUIDE RELEASE 4.5 DRAFT 0.
MovingMedia 2000 iCell Macro with iPA Installation Guide Page 2 of 14
Copyright © 2004 UTStarcom Incorporated. All rights reserved. Copyright © 2004, UTStarcom, Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without prior written permission from UTStarcom, Inc. UTStarcom, Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of UTStarcom, Inc.
1 PREFACE 1.1 Objective This document provides installation and configuration instructions for setting up an iCellCDMA2000 1X iPA system. It covers physical installation only. 1.2 Organization The major sections of this guide are as follows: Table 1-1: Organization Table Chapter Title Description Chapter 1 Preface Introduction to the Installation Guide.
1.3 Reference Documents The following table summarizes the applicable reference documents. Table 1-2: Reference Documents Ref. Title 1 User Manual Pico BTS 2 iCell CDMA2000 1X Alarms and Statistics 3 iCell CDMA2000 1X Configuration Guide Number 1.4 Acronyms and Abbreviations The following table summarizes the acronyms and abbreviations used throughout the document.
PDSN PSTN RF SMSC SNMP SNTP TBD TCP Packet Data Serving Node Public Switch Telephone Network Radio Frequency Short Message Service Center Simple Network Management Protocol Simple Network Timing Protocol To Be Defined Transmission Control Protocol Time Of Day TOD MovingMedia 2000 iCell Macro with iPA Installation Guide Page 6 of 14
2 iCell MACRO SYSTEM DESCRIPTION This chapter provides an iCell system description. 2.1 Introduction The iCell is an IP-based solution for CDMA2000 1X radio access networks. The iCell system provides the overall functionality of a CDMA2000 1X Base station transceiver subsystem (BTS) and soft base station controller (sBSC), providing an IP over Ethernet interface to the core network. For Macro coverage small footprint iPA Bidirectional amplifier is added to the basic BTS configuration.
2.2 iPA 1900 MHz System Components The iPA is only used when the iCell is installed in a 19" rack-mounted configuration. The iPA is a single sector bi-directional amplifier that incorporates: A high power amplifier (HPA) Two low noise amplifiers (LNA) for receive diversity, frequency conversion and selectivity capabilities (for each sector).
3 BTS PHYSICAL INSTALLATION 3.1 General This chapter provides physical installation and wiring instructions for the iPA. 3.2 Unpacking Upon receipt of, and before opening the iCell packages, inspect for any damage that might have occurred during shipping. If the package shows any signs of external damage or rough handling, notify your carrier's representative. CAUTION All modules are susceptible to electrostatic discharge (ESD) even while installed.
3.3.1 BTS 19" Rack Mount See Figure 3-1 and Figure 3-2. 1. Insert the BTS 1X 19" unit into a 19" rack. Secure with four NF10 screws. 2. Connect BTS 19" Rack Mount according to paragraph 3.4.2. Figure 3-1: BTS 19' Rack Mont Rear View Figure 3.2: BTS 19” Rack Mount Front View Figure 3.3: iPA Front View Figure 3.
MovingMedia 2000 iCell Macro with iPA Installation Guide Page 11 of 14
3.4 Interface Connections 3.4.1 BTS and iPA Interface Connections Verify that the power switch is off on both the iPA and the BTS unit 3.4.2 BTS to iPA Interface Connection Figure 3-1 illustrates the wiring diagram of the BTS and iPA for Macro coverage. Table 3-1 provides the wiring parameters. Figure 3.
iWAN Installation Guide Table 3-1: iBTS 19" Wiring iBTS Destination Name Type Cable MCN S3 RX1 SMA 45-89330-M3 iPA RX3 Diversity SMA S3 TX/RX0 SMA 45-89330-M3 iPA TX/RX3 Diversity SMA S2RX2 SMA 45-89330-M3 iPA RX2Diversity SMA S2 TX/RX0 SMA 45-89330-M3 iPA TX/RX2 Diversity SMA S1 RX2 SMA 45-89330-M3 iPA RX1 Diversity SMA S1 TX/RX0 SMA 45-89330-M3 iPA TX/RX1 Diversity SMA iPA 1 RJ45S 45-89331-M2 iPA Com 1 DB-9 iPA 2 RJ45S 45-89331-M2 iPA Com 2 DB-9 iPA 3 RJ45S
3.4.2.1 Connecting to iPA for three sector case: To Connect the iBTS to the iPA: Connect the iBTS iPA 1 RJ-45 connector to the iPA COM 1 DB-9 connector with cable MCN 45-89330-M3. Connect the iBTS iPA 2 RJ-45 connector to the iPA COM 2 DB-9 connector with cable MCN 45-89330-M3. Connect the iBTS iPA 3 RJ-45 connector to the iPA COM 3 DB-9 connector with cable MCN 45-89330-M3. Connect the iBTS S1 RX1 SMA Connector to the iPA RX1 Diversity SMA connector with cable MCN 45-89331-M2.
