PROFESSIONAL CD PLAYER IN OUT CUE TIME USERS MANUAL
Important To Safety WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: 1. Handle the power supply cord carefully Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. When removing from wall outlet, be sure to remove by holding the plug attachment and not by pulling the cord. NOTE: This CD player uses the semiconductor laser.
Important Safety Instructions 1. Read Instructions – All the safety and operating instructions should be read before this product is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5.
Features Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ 10 seconds of anti-shock memory Instant start Seamless loop Pitch range : +/-100% +/-0.1% 4 banks for Sampler and Cue memory, <5 sec.
1. DISPLAY PANEL ─ LCD-display for displaying the different modes and functions. 2. SEARCH WHEEL - This wheel has 4 forward and 4 reverse speed positions allowing you to quickly scan through tracks. The more you turn the wheel in either direction the faster you search. 3. TRACK BUTTON - These buttons are used the select a track. Tapping the button will forward/back skip to the next track, holding down the button will rapidly forward/back skip through the tracks. 4.
AUDIO OUT 21 DIGITAL OUT RELAY 22 23 21. AUDIO OUT-SOCKETS - This analogue signal requires RCA (left & right) connections. Connect this output to the respective input of your mixer (Line/Aux). POWER ON OFF 24 25 25 24. POWER SWITCH - Press this button to activate the unit.(i.e. Power ON/OFF) 25. AC CONNECTION - Plug in the power supply cable here. 22. DIGITAL OUT-SOCKET - This digital signal requires one SP/DIF (75 Ohm) connection.
Set-up 1.Checking the Contents Check the carton and packaging contents for the following items: 1. 2. 3. 4. Tabletop unit Operating instructions One RCA cable. One AC power cord. 2. Installing the Unit 1. Place your unit on a flat leveled surface. 2. Be sure the player is in a well-ventilated area where it will not be exposed to direct sunlight, high temperatures, or high humidity. 3. Try to place the unit as far as possible from TVs and tuners, as the unit may cause undesirable interference.
Operating instructions 1.Opening and Closing This operation only works when the power is on. Press the OPEN/CLOSE button to open or close the disc tray, or press PLAY button, the disc tray automatically closes. If tray is not closed after 60 seconds it will close automatically and pause. The disc tray cannot be opened during playback to prevent playback from being interrupted if the OPEN/CLOSE button is pressed accidentally. Stop playback, then press the OPEN/CLOSE button. 2.
Operating instructions 12.Seamless Loop Play (Cont.) a- (Must be in SEAMLESS LOOP mode). If a SEAMLESS LOOP has not been created, follow instructions on this page for creating a SEAMLESS LOOP. If a SEAMLESS LOOP has already been created, press RELOOP BUTTON to reenter the SEMALESS LOOP mode. b- Next, press OUT/EXIT BUTTON to return to normal play (figure 6). This disengages the SEAMLESS LOOP mode. SEAMLESS LOOP IN OUT Fig.
Specifications 1. APPLICATION Model S-350 2. POWER SOURCE AC 230V, 50Hz, 14W 3. DIMENSIONS 348 (W)x 246 (D)x 106 (H) mm 4. WEIGHT 3 Kgs 5. CHARACTERISTICS (TEST DISC: TCD-782, LOAD=47Kohm) ITEM TYPICAL LIMIT (1) Output level 1Vrms+/-0.5dB 1Vrms+/-1dB (2) Channel balance within 0.5dB within1dB (3) Frequency response 20-20KHz,+/-0.5dB 20-20KHz,+/-1dB (4) De-emphasis response +/-2.5dB +/-3dB (5) Channel separation 83dB 75dB (6) T.H.D. + NOISE*1 0.01% 0.