Instruction Manual EN Battery Power Tool DA Batteridrevet værktøj DE Akkuwerkzeug ES Herramienta de batería FI Akkutyökalu FR Outil électrique alimenté par batterie IT Elettroutensile a batteria NL Accugereedschap NO Batteridrevet verktøy PL Elektronarzędzie akumulatorowe PT Ferramenta eléctrica com bateria SV Batteridrivet verktyg PB2500 Smart Blind rivet tool Battery Power Tool
UK DK DE ES 2 FI FR IT NL NO PL PT SE
PB2500 Smart (Ref. Section2.4) Figure 1 F 3.2 [1/8] 4.0 [5/32] D F G E H C B I J A Model no. / Serial no.
PB2500 Smart (Ref. Section2.
Original Instruction ENGLISH ©2020 Stanley Black & Decker All rights reserved. The information provided may not be reproduced and/or made public in any way and through any means (electronically or mechanically) without prior explicit and written permission from STANLEY Engineered Fastening. The information provided is based on the data known at the moment of the introduction of this product.
ENGLISH This instruction manual must be read by any person installing or operating this tool with particular attention to the following safety rules. 1. SAFETY DEFINITIONS The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
ENGLISH Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Adopt a firm footing or a stable position before operating the tool. Operators and others in work area must wear ANSI Z87.1 CAN/CSA Z94.3 or other approved safety glasses with side shields. Always wear safety glasses and ear protection during operation.
ENGLISH Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock, or electrocution. Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.
ENGLISH 2. If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. 3. Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention. WARNING: Burn hazard.
ENGLISH STANLEY Engineered Fastening policy is one of continuous product development and improvement and we reserve the right to change the specification of any product without prior notice. 2. SPECIFICATIONS UNDER NO CIRCUMSTANCES SHOULD ANY MAINTENANCE OR SERVICING BE CONDUCTED APART FROM NOSE EQUIPMENT CHANGE. 2.1 TECHNICAL DATA 2.1.1 Voltage Type Battery Type Weight (without battery pack) Kg PB2500 Smart 18 nom / 20 max 3 Li-ion 1.46 dB(A) dB(A) dB(A) dB(A) 76.1 3 87.
ENGLISH 2.1.3. Battery Pack* Battery type Voltage Capacity Weight Charging duration** Charger** Battery type Battery type Mains voltage Input frequency Weight Fuses Europe U.K. & Ireland Hz Kg Li-ion 18 nom / 20 max 2.0/4.0 0.35/0.61 30/60 NA Li-ion 120 60 0.50 230 V tools 230 V tools 10 Amperes. Mains 3 Amperes. in plugs VDC Ah Kg min VAC JP Li-ion 100 50/60 0.50 QW/GB/XE/XD/KR Li-ion 230 50 0.
ENGLISH 2.2 PLACING SPECIFICATIONS Rivet Type OPEN END CLOSED END AVEX®/ STAVEX® AVINOX®/ AVIBULB® HR/HT INTERLOCK® HEMLOK® KLAMP-TITE®/ KTR BULBEX®/LS/TL MONOBOLT® MULTI-GRIP PULL-THRU (PT) Q RIVET T-LOK® T Rivet AVSEAL®II 2.4mm [3/32”] ● 3.0mm ● ● PLACING CAPACITY PB2500 Smart 3.2mm 4.0mm 4.3mm [1/8”] [5/32”] ● ● ● ● 4.8mm [3/16”] ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 5.0/6.0/ 7.
ENGLISH **If the Model Number purchased is a bare tool then only the Cordless Installation Tool will be supplied with a standard set of 4.8mm [3/16”]. 2.4 MAIN COMPONENTS LIST (for complete tool explosion and Bill of Material please see service manual) PB2500 Smart drawing can be found inside the front cover A B C D E F G H I J K L 2.
ENGLISH 3. TOOL USE & SET UP The PB Series of tools are designed for installation of STANLEY Engineered Fastening Blind Fasteners. DO NOT use under wet conditions or in presence of flammable liquids or gases. READ ALL SAFETY WARNINGS AND INSTRUCTIONS BEFORE PUTTING TOOL INTO SERVICE. Electrical Safety The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate.
ENGLISH 4.2 CHARGERS Your tool uses a DEWALT® charger. Be sure to read all safety instructions before using your charger. The charger requires no adjustment and is designed to be as easy as possible to operate. Charging Procedure (fig. 2) Plug the charger into an appropriate outlet before inserting the battery pack. (Refer to the Charger Specifications in Section 2) Insert the battery pack (K) into the charger, making sure the pack is fully seated in the charger.
ENGLISH Slide it into the handle until the battery pack is firmly seated in the tool and ensure that it does not disengage. TO REMOVE THE BATTERY PACK FROM TO THE HANDLE Press battery release button and firmly pull the battery pack out of the tool handle. Insert battery pack into the charger as described in the charger section for this manual. Storage Recommendations The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold.
ENGLISH Emptying the mandrel collector (W) (fig. 6) The mandrel collector is used to collect the waste mandrels. The mandrel collector must be emptied depending on the size of the blind rivets used. Nom. Rivet Dia. 2.4 mm [3/32”] 3.2 mm [1/8”] 4.0 mm [5/32”] 4.8 mm [3/16”] 6.4 mm [1/4”] Approx. Capacity (PB2500 Smart) 600 360 200 150 Not applicable Tilt the tool back to allow all waste mandrels to fall into the mandrel collector.
ENGLISH Apply grease to the inside of the jaw guide (P) where the jaws (Q) make contact. A Molybdenum Disulfide based grease is recommended. Mount the spring (S) Mount the jaw pusher(R) and the jaws (Q) Press front clutch (U) and tighten the jaw guide (P). Release front clutch (U). Mount the nose housing (B). Tighten the nose housing nut (C). Perform tool reset function to ensure the tool is at the initial home position as described in section 5.
ENGLISH 7. EC-DECLARATION OF CONFORMITY Original We, STANLEY Engingineered Fastening, Nippon POP Rivets and Fasteners Ltd., Hosoda, Noyori-cho, Toyohashi, Aichi, 441-8540 JAPAN, declare under our sole responsibility that the product: Description Brand/Model Serial No.
ENGLISH 8. STATEMENT FOR RADIO This equipment complies with CE radiation exposure requirement set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. 8.1 SPECIFICATIONS FOR RADIO This tool has a RF module (ESP32-WROOM-32 by Espressif, FCC code: 2AC7Z-ESPWROOM32, IC code: 21098-ESPWROOM32) and it operates with the conditions below.
ENGLISH 9. PROTECT YOUR INVESTMENT! 9.1 STANLEY ENGINEERED FASTENING TOOL WARRANTY STANLEY Engineered Fastening warrants that all power tools have been carefully manufactured and that they will be free from defect in material and workmanship under normal use and service for a period of one (1) year. We will extend the warranty on your tool (excluding batteries and charger) from one (1) year to two (2) years when you register your tool online. (Ref. Section 9.2 at the bottom of this page.
ENGLISH 22