User Guide

ManualsBrandsStand Steady ManualsAccessories & SuppliesStand Steady Winston Workstation Triple Monitor Mount Sit-Stand Desk (Innovative WNST-3) | Three Monitor Standing Desk Workstation Converter with VESA Mount| Height Adjustable! (3 Monitor/Black)

800.524.2744 www.LCDarms.com

STEP 1 | COLUMN ................................................................................................................... Page 3

STEP 2 | MOUNT .........................................................................................................................Page 4

STEP 3 | WORK SURFACE ...............................................................................Page 5

STEP 4 | CENTER BEAM .......................................................................................Page 6

STEP 5 | EXTENSION BEAMS ..............................................................Page 7

STEP 6 | MONITOR TILTER..............................................................................Page 8

STEP 7 | MONITOR CUPS ..................................................................................Page 9

STEP 8 | CABLE MANAGEMENT .....................................................Page 10

NOTE: Depending on your Winston Workstation

configuration,

you may not receive all the parts shown within this instruction booklet.

Installation may require two people.

WNST-3 & WNST-4

Winston Workstation

Triple & Quad

| Installation Instructions

PAGE 1 OF 11

Summary of content (11 pages)

PAGE 1
WNST-3 & WNST-4 Winston Workstation® Triple & Quad | Installation Instructions 5 STEP 1 | COLUMN....................................................................................................................Page 3 4 STEP 2 | MOUNT..........................................................................................................................Page 4 1 STEP 3 | WORK SURFACE................................................................................Page 5 STEP 4 | CENTER BEAM............
PAGE 2
WNST-3 & WNST-4 Depending on your Winston Workstation® configuration, you may not receive all parts shown below. A Work Surface H 411469 B Column Felt Pad I Freestanding Base J Cable Retainer K 3/8-16 x 1" FHSCS L 10-32 x 1" FHSCS 711467 800.524.2744 www.LCDarms.
PAGE 3
STEP 1 COLUMN IMPORTANT: Do not pull excessively on cable – doing so may result in accidental actuation of column. B A 1 2 3 i R Use 7/32" Allen wrench to press cable firmly into place. 800.524.2744 www.LCDarms.com PAGE 3 OF 11 Confirm cable is properly seated into position.
PAGE 4
STEP 2 MOUNT 1 2 3 Hang base plate over edge of work surface to allow access to countersunk holes. Side of base plate with felt pads should be face down. Place work surface on base plate to aid as a counterbalance. C D 4 5 E Note the orientation of column cable exit and base plate – cable should exit in direction as shown. 7/32" F 800.524.2744 www.LCDarms.
PAGE 5
STEP 3 WORK SURFACE 1 2 Slide utility tray onto work surface. Utility tray simply rests on top of work surface. Two people may be required to install work surface to column. One to hold the work surface and the second person to secure the column clamp. H I 1/8" G A i 1 3 IMPORTANT: Tighten bolts evenly. Work surface clamp should sit flush against the column, ensure there are no gaps. Also, it is important the work surface clamp is level. 800.524.2744 www.LCDarms.
PAGE 6
STEP 4 CENTER BEAM 1 2 J H K 1/8" 3 4 L 1/8" i IMPORTANT: Tighten bolts evenly. The beam should sit flush against the column, ensure there are no gaps. Also, it is important the work surface clamp is level. 800.524.2744 www.LCDarms.
PAGE 7
STEP 5 EXTENSION BEAMS 1 2 M N Z N 1/8" 1/8" O Q 3 i R P 1/8" 800.524.2744 www.LCDarms.
PAGE 8
STEP 6 MONITOR TILTER STANDARD TILTER & SPRING TILTER 1 2 QUICK RELEASE TILTER 1 2 U or V T W X W S Y FINE TUNE HEIGHT ADJUST TILTER 1 2 3 4 T U or V W S S Z S 800.524.2744 www.LCDarms.
PAGE 9
STEP 7 MONITOR CUPS 1 2 i 7/32" AA AA BB 1/8" 800.524.2744 www.LCDarms.
PAGE 10
STEP 8 CABLE MANAGEMENT 1 2 DD EE 800.524.2744 www.LCDarms.
PAGE 11
HEIGHT ADJUSTMENT Press button and hold. i Is your height adjust button not working? If so, make the adjustments below. 1 Slide workstation so that the work surface hangs over desk edge to allow access to underneath the work surface. 2 Loosen the two screws as shown. 3 Slide bracket in the direction shown and tighten screws. 4 Test height adjust button – readjust by repeating the steps above as necessary. 800.524.2744 www.LCDarms.com PAGE 11 OF 11 Lift up/down. Release to lock in place.