Cut Sheet

ManualsBrandsSSAC ManualsControl & AutomationDIGI-TIMER(Interval) 1m-100m

www.ssac.com • 800-843-8848 • fax: 605-348-5685

TSD2 SeriesTimer - Interval

Available Models:

Time Delay

Range ..................................0.1s - 100h in 7 adjustable ranges or xed

Repeat Accuracy ........................±0.1% or 20ms, whichever is greater

Tolerance (Factory Calibration) ............≤ ±1%

Reset Time ..............................≤ 150ms

Time Delay vs Temp. & Voltage ...........≤ ±1%

Input

Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 120, or 230VAC

Tolerance ...............................±20%

AC Line Frequency ......................50/60 Hz

Power Consumption .....................≤ 2VA

Output

Type ...................................Solid state

Form ...................................NO, closed during timing

Maximum Load Current ..................1A steady state, 10A inrush at 60°C

Off State Leakage Current ................≅ 5mA @ 230VAC

Voltage Drop ...........................≅ 2.5V @ 1A

Protection

Circuitry ...............................Encapsulated

Dielectric Breakdown ....................≥ 2000V RMS terminals to mounting surface

Insulation Resistance .....................≥ 100 MΩ

Mechanical

Mounting ..............................Surface mount with one #10 (M5 x 0.8) screw

Dimensions .............................2 x 2 x 1.21 in. (50.8 x 50.8 x 30.7 mm)

Termination ............................0.25 in. (6.35 mm) male quick connect terminals

Environmental

Operating / Storage Temperature .........-40° to 75°C / -40° to 85°C

Humidity ...............................95% relative, non-condensing

Weight .................................≅ 2.4 oz (68 g)

Order Table:

Specications

The TSD Series is designed for more demanding

commercial and industrial applications where

small size and accurate performance are required.

The factory calibration for xed time delays is

within 1% of the target time delay. The repeat

accuracy, under stable conditions, is 0.1% of the

time delay. The TSD Series is rated to operate over

an extended temperature range. Time delays of 0.1

seconds to 100 hours are available. The output is

rated 1A steady and 10A inrush. The modules are

totally solid state and encapsulated to protect the

electronic circuitry.

Operation (Interval):

Upon application of input voltage, the time delay begins.

The output is energized during the time delay. At the end

of the time delay, the output de-energizes and remains

de-energized until input voltage is removed.

Reset: Removing input voltage resets the time delay and

the output.

For more information see:

Appendix A, pages 156-164 for function descriptions

and diagrams.

Appendix B, page 165, Figure 1 for dimensional drawing.

Features:

• Fixed or adjustable delays from 0.1s - 100h

• ±0.1% repeat accuracy

• ±1% factory calibration

• 24, 120, or 230VAC

• 1A, solid-state output

• Encapsulated

Approvals:

Connection:

TSD2221

TSD2411S

TSD24145S

TSD241600S

TSD2434

Auxiliary Products:

• External adjust potentiometer:

P / N : P 1 0 0 4 - 9 5

P/N: P1004-95-X

• Female quick connect:

P / N : P 1 0 1 5 - 6 4 ( A W G 1 4 / 1 6 )

• Quick connect to screw adaptor:

P/N: P1015-18

• Mounting bracket: P/N: P1023-6

• DIN rail: P/N: C103PM (Al)

• DIN rail adaptor: P/N: P1023-20

• Versa-knob: P/N: P0700-7

TSD2

Input Voltage

─2 - 24VAC

─4 - 120VAC

─6 - 230VAC

Adjustment

─1 - Fixed

─2 - External adjust

─3 - Onboard adjust

Time Delay*

─0 - 0.1 - 10s

─1 - 1 - 100s

─2 - 10 - 1000s

─3 - 0.1 - 10m

─4 - 1 - 100m

─5 - 10 - 1000m

─6 - 1 - 100h

*If xed delay is selected, insert

delay (0.1 - 1000) followed by (S) sec.

or (M) min. or (1 - 100) (H) hours

L1 N/L2

External Resistance vs. Time Delay:

If desired part number is not listed, please call us to

see if it is technically possible to build.

is used when external adjustment is ordered.

Summary of content (9 pages)

PAGE 1
Timer - Interval Connection: L1 N/L2 TSD2 Series The TSD Series is designed for more demanding commercial and industrial applications where small size and accurate performance are required. The factory calibration for fixed time delays is within 1% of the target time delay. The repeat accuracy, under stable conditions, is 0.1% of the time delay. The TSD Series is rated to operate over an extended temperature range. Time delays of 0.1 seconds to 100 hours are available.
PAGE 2
Appendix A - Timer Functions Selecting a Timer’s Function Selecting one of the five most common timing functions can be as easy as answering three questions on the chart below. If you have trouble answering these questions, try drawing a connection diagram that shows how the timer and load are connected. Time diagrams and written descriptions of the five most popular functions, plus other common functions.
PAGE 3
Appendix A - Timer Functions INTERNATIONAL TIMING FUNCTION SYMBOLS = Delay-on-Make; ON-delay = Delay-on-Break; OFF-delay = Delay-on-Make & Break; ON and OFF-delay = Interval; Impulse-ON = Trailing Edge Interval; Impulse-OFF = Single Shot; Pulse Former = Flasher - ON Time First; Recycling Equal Times - ON First = Flasher - OFF Time First; Recycling Equal Times - OFF First = Recycling - Unequal Times; Pulse Generator = Recycling - Unequal Times Starting with ON or OFF = Delay-on-Make & Interval; Single Pulse
PAGE 4
Appendix A - Timer Functions Timer Functions Popular Functions ® Recycling: (ProgramaCube Functions RE, RD, RXE, RXD) (Flasher, Pulse Generator, Recycle Timing, Repeat Cycle, Duty Cycling) OPERATION: Upon application of input voltage, the output (relay or solid state) energizes and the ON time begins. At the end of the ON time, the output de-energizes and the OFF time begins. At the end of the OFF time, the output energizes and the cycle repeats as long as input voltage is applied.
PAGE 5
Appendix A - Timer Functions ® Single Shot: (ProgramaCube Functions S or SD) (Pulse Former, One Shot Relay, Single Shot Interval, Pulse Shaping) OPERATION: Input voltage must be applied before and during timing. Upon momentary or maintained closure of the initiate switch, the output (relay or solid state) energizes and the time delay begins. At the end of the delay, the output de-energizes. Opening or reclosing the initiate switch during timing has no effect on the time delay.
PAGE 6
Appendix A - Timer Functions Timer Functions Two Functions in One Timer ® Delay-on-Make/Delay-on-Break: (ProgramaCube Function MB) (ON-delay/OFF-delay, Delay on Operate/Delay on Release, Sequencing ON & OFF, Fan Delay, Prepurge & Postpurge) OPERATION: Input voltage must be applied at all times. The output (relay or solid state) is deenergized. Upon closure of the S1 initiate switch, the delay-on-make time delay (TD1) begins. At the end of TD1, the output (relay or solid state) energizes.
PAGE 7
Appendix A - Timer Functions Timer Functions Two Functions in One Timer ® Delay-on-Make/Recycle: (ProgramaCube Function MRE) OPERATION: Upon application of input voltage, TD1 begins and the output (relay or solid state) remains de-energized. At the end of TD1, the TD2 recycle function begins and the output (relay or solid state) cycles ON and OFF for equal delays. This cycle continues until input voltage is removed.
PAGE 8
Appendix A - Timer Functions Timer Functions Counting and Switching Functions ® Leading edge flip-flop: (ProgramaCube Function F) OPERATION: Input voltage must be applied before and during operation. The operation begins with the output (relay or solid state) de-energized. Upon momentary or maintained closure (leading edge triggered) of the initiate switch S1, the time delay begins. At the end of the time delay, the output energizes and remains energized.
PAGE 9
Appendix B - Dimensional Drawings FIGURE 1 FIGURE 2 FIGURE 3 CT; ESD5; ESDR; FS100; FS200; FS300; KRD3; KRD9; KRDB; KRDI; KRDM; KRDR; KRDS; KRPD; KRPS; KSD1; KSD2; KSD3; KSD4; KSDB; KSDR; KSDS; KSDU; KSPD; KSPS; KSPU; KVM; T2D; TA; TAC1; TAC4; TDU; TDUB; TDUI; TDUS; TL; TMV8000; TS1; TS2; TS4; TS6; TSB; TSD1; TSD2; TSD3; TSD4; TSD6; TSD7; TSDB; TSDR; TSDS; TSS; TSU2000 HLV; HRD3; HRD9; HRDB; HRDI; HRDM; HRDR; HRDS; HRID; HRIS; HRIU; HRPD; HRPS; HRPU; HRV; RS HSPZ FIGURE 4 FIGURE 5 TRDU FIGURE 6 TR