Access Network Setup Guide 033-100566-001, Issue 1B PRELIMINARY AND UNRELEASED
The information in this manual is subject to change without notice. All statements, information and recommendations in this manual are believed to be accurate, but are presented without warranty of any kind, expressed or implied. Users must take full responsibility for their use of any products.
Preface About this Manual This guide provides information on how to set up the STRIDE™ 2400 access network. It describes how to mount, install, connect and power up the STRIDE2400 equipment. If you require additional installation options, you can refer to the STRIDE2400 Terminal Station Setup Guide or the STRIDE2400 Procedures Guide, for further details. This setup guide is intended for service personnel responsible for installing the STRIDE2400 access network.
STRIDE2400 Access Network Setup Guide
Table of Contents Chapter 1 Chapter 2 Chapter 3 Introduction .............................................................................................................................................. 7 1.1 STRIDE2400 Access Network ............................................................................................ 8 1.2 STRIDE2400 Access Network Setup Overview ................................................................ 10 Preparation .................................................
STRIDE2400 Access Network Setup Guide 3.3 Powering Up the SBS ....................................................................................................... 56 3.4 Verifying the SBS LED Status Indicators .......................................................................... 58 3.5 3.5.1 3.5.2 3.5.3 3.5.4 3.5.5 3.5.5.1 3.5.5.2 Installing the SBS Battery Enclosure ................................................................................
Chapter 1 Introduction This chapter introduces the STRIDE2400 access network and describes the installation phases for setting up the STRIDE2400 equipment.
STRIDE2400 Access Network Setup Guide 1.1 STRIDE2400 Access Network STRIDE2400 is a point-to-multipoint fixed access network that operates in the 2.4 GHz Industrial Scientific Medical (ISM) unlicensed band providing voice and broadband data services to subscribers within a 11 mile (18 km) radius. With a STRIDE2400 FWA network, service providers can quickly and reliably deliver: • Voice service at 32 Kbps ADPCM (ITU G.726) • Voiceband data service at 64 Kbps PCM (ITU G.
Introduction PTP Backhaul Radio 2.4 GHz Airlink PSTN STS Remote Switch Network Signaling Adapter SBS T1 T1 or 10 BaseT Data Network T1 Router 10 BaseT STS RS03041001 INSIGHT NMS Figure 1.
STRIDE2400 Access Network Setup Guide 1.2 STRIDE2400 Access Network Setup Overview The setup of the STRIDE2400 access network consists of three phases. Each phase must be conducted in the order provided to ensure the optimum performance of the access network equipment. The three phases to deploy the STRIDE2400 access network include: 1. Preparation: describes the pre-installation requirements for the SBS and STS sites. 2.
Introduction 1 Preparation Installing the Antenna 3 Installing the Antenna Installing the SBS 2 S T S SBS Installation Installing the STS Installing the STS Power Pack S B S RS03032701 Installing the SBS Battery Enclosure STS Installation Figure 1.
STRIDE2400 Access Network Setup Guide
Chapter 2 Preparation This chapter outlines the pre-installation requirements for the SBS and STS sites to ensure proper operation of the STRIDE2400 equipment.
STRIDE2400 Access Network Setup Guide 2.1 Safety Guidelines To ensure the proper handling of all equipment and the safety of service personnel, it is important to comply with the precautions outlined in this section. Failure to comply with the following guidelines may void your warranty. 2.1.1 Installation Precautions SR Telecom equipment must be installed by qualified service personnel who are trained in the correct procedures for handling and installing the equipment.
Preparation 2.1.2 Electrostatic Discharge (ESD) Precautions To avoid damage to the equipment, service personnel must be at the same electrical potential as the equipment. Before handling the equipment, it is important to safely discharge any static electricity.
STRIDE2400 Access Network Setup Guide 2.1.4 Grounding and Lightning Protection Guidelines A well-constructed grounding system helps protect SR Telecom equipment from lightning strikes.
Preparation 2.1.5 Antenna Guidelines To properly mount the external antennas, ensure that these guidelines are followed: 2.1.
STRIDE2400 Access Network Setup Guide 2.2 Tool Requirements RB03071001 When installing the STRIDE2400 equipment, the following tools are required.
Preparation 2.3 Site Requirements Before unpacking and installing STRIDE2400 equipment, it is important to ensure that the site complies with STRIDE2400 environmental and power requirements. SBS and SBS Battery Enclosure Environmental Requirements Operating Temperature -40°F to +115°F (-40°C to +46°C) plus solar load Humidity Outdoor conditions; wind, rain, and snow Power Requirements SBS Input Voltage -48 VDC nominal (-40.
STRIDE2400 Access Network Setup Guide STS and STS Power Pack Environmental Requirements Operating Temperature -40°F to +115°F (-40°C to +46°C) plus solar load Humidity Outdoor conditions; wind, rain, and snow Power Requirements STS Input Voltage +24 VDC nominal (15 VDC to 28 VDC) STS Power Pack Input Voltage 110 VAC, 50/60 Hz nominal (90 VAC to 130 VAC) STS Input Current 2.2 A STS Power Pack Input Current 1.4 A max.
Chapter 3 STRIDE2400 Base Station Installation This chapter describes the procedures for installing, connecting and powering up the SBS equipment.
STRIDE2400 Access Network Setup Guide 3.1 Installing the SBS Antenna The antenna provides the wireless radio communication link between the SBS and STSs. The antenna is an outdoor unit that is typically installed on a tower or pole. This section describes the procedures for installing the SBS antenna. To install the SBS Antenna 22 1. Unpack the SBS Antenna package contents and verify that all components are delivered as described in Section 3.1.1 “Verifying the SBS Antenna Package Contents” on page 23.
STRIDE2400 Base Station Installation 3.1.1 Verifying the SBS Antenna Package Contents Verify that you have received the following materials with your SBS antenna package. If any materials are missing or damaged, please contact SR Telecom technical services. SBS Antenna and mounting hardware RB03082801 SBS Antenna Installation instructions Mounting Hardware SBS Antenna Package Figure 3.
STRIDE2400 Access Network Setup Guide 3.1.2 Mounting the SBS Antenna The SBS requires a single sectoral or omnidirectional antenna to provide the wireless communication link to the STS sites. Depending on the antenna purchased, different mounting methods may apply.
STRIDE2400 Base Station Installation SBS Antenna Mounting Hardware RS03061802 SBS Antenna Figure 3.
STRIDE2400 Access Network Setup Guide 3.1.3 Installing the SBS Antenna Cable The SBS Antenna Cable is used to connect the SBS antenna to the SBS equipment. The SBS Antenna Cable carries the -48 VDC power that is required to operate the antenna, as well as to transmit and receive data. Included with the SBS antenna cable package are the following: Connectorized Coaxial Cable (N-Type) Grounding Kits (2) Hanger Kits (2) RB03082802 Wrap Lock SBS Antenna Cable Package Figure 3.
STRIDE2400 Base Station Installation Requirements: Included with SBS Antenna Cable: N-type Connectorized Coaxial Cable, Hanger Kits, Wrap Lock Tools: Vulcanized and electrical tape Guidelines: E • To prevent water damage, seal all outdoor connectors with vulcanized and electrical tape • Install clamps every 3 feet (1 m) To connect the SBS Antenna Cable to the SBS antenna 1. Connect the SBS Antenna Cable to the SBS antenna and tighten with wrench, as shown in Figure 3.4. 2.
STRIDE2400 Access Network Setup Guide 3.1.4 Grounding the SBS Antenna Grounding ensures that the SBS antenna equipment is protected against lightning strikes or improper handling that can damage the antenna. Depending on the antenna purchased, different grounding methods may apply.
STRIDE2400 Base Station Installation 45° Cone of protection Lightning Rod Sectoral Antenna RS03050801 Grounding Kit (Included with Antenna Cable) SBS RF Lighting Protection on Antenna Cable Grounding Kit (Included with Antenna Cable) SBS Ground Wire SBS Battery Enclosure SBS Battery Enclosure Ground Wire Figure 3.
STRIDE2400 Access Network Setup Guide 3.2 Installing the SBS The SBS is an outdoor unit that aggregates the voice and data traffic from the STSs over the 2.4 GHz airlink and interfaces to backhaul equipment using T1 links. This section provides the procedures for installing the SBS equipment. To install the SBS 30 1. Unpack the SBS package contents and verify that all components are delivered as described in Section 3.2.1 “Verifying the SBS Package Contents” on page 31. 2.
STRIDE2400 Base Station Installation 3.2.1 Verifying the SBS Package Contents Verify that you have received the following materials with your SBS main package. If any materials are missing or damaged, please contact SR Telecom technical services.
STRIDE2400 Access Network Setup Guide 3.2.2 Mounting the SBS To ensure that sufficient space is allocated for the installation of the SBS cables, SR Telecom recommends that you first estimate the amount of space required prior to mounting the equipment. A minimum clearance of 6 in. (15 cm) below the SBS cabinet is required for cable connections, as shown in Figure 3.7. The SBS comes fully-installed in an outdoor cabinet.
EK03052901 STRIDE2400 Base Station Installation 6 in. for Cable Connections Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.2.1 Mounting the SBS on a Wooden Pole The SBS must be mounted on a wooden pole of sufficient diameter (at least 4.7 in.) to withstand environmental conditions such as wind, vibrations and eathquakes. Requirements: Included with SBS: SBS Wood Pole Mount Installation Kit Tools: Drill, Torx screwdriver, adjustable wrench Guidelines: • Determine the location of the SBS prior to moving the equipment to its final location • Drilling wood may cause flying chips.
STRIDE2400 Base Station Installation SBS Step 7 Torx Screw Step 2 RB03071601 Step 6 Bolt Washer Step 1 SBS Back Panel Step 3 Mounting Rod Pole Bracket Washer Lock Washer Nut Nut Large Washer Washers Adjustment Brackets Step 5 Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.2.2 Mounting the SBS on a Metal Pole The SBS must be mounted on a metal pole of sufficient diameter (at least 3 in.) to withstand environmental conditions such as wind, vibrations and eathquakes. Requirements: Included with SBS: SBS Metal Pole Mount Installation Kit Tools: Torx screwdriver, adjustable wrench Guidelines: • Determine the location of the SBS prior to moving the equipment to its final location • Pole must be at least 3 in. (7.
STRIDE2400 Base Station Installation SBS Step 5 Torx Screw RB03090501 Step 4 Step 1 Step 2 Mounting Rods Bolt Washer SBS Back Panel Pole Bracket Washer Lock Washer Nut Step 3 Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.2.3 Mounting the SBS to a Concrete Base The SBS can be anchored to a cement floor. Requirements: Included with SBS: SBS Concrete Base Installation Kit Tools: Allen Key (10 mm), drill, hand setting tool Guidelines: E • Determine the location of the SBS prior to moving the equipment to its final location • Drilling concrete may cause flying chips of stone.
STRIDE2400 Base Station Installation RB03052701 SBS Rubber Washer Lock Washer Hex Bolt Bolt Front Panel SBS Concrete Base 16.803 in. 21.06 3 in. Anchor Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.2.4 Mounting the SBS on a Wall The SBS can be mounted on a variety of wall surfaces such as gypsum, plywood or cement. Prior to mounting the SBS cabinet, ensure that you acquire the appropriate anchoring hardware.
RB03090502 STRIDE2400 Base Station Installation Concrete Wall Anchoring Hardware SBS Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.3 Grounding the SBS Grounding the SBS helps prevent serious injury to service personnel and avoids damage to the equipment.
STRIDE2400 Base Station Installation RB03061001 Grounding Bus Bar Ground Connector Ground Fitting 6 AWG Ground Wire Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.4 Connecting the SBS Cables This section provides the procedures for connecting the antenna cables, T1 lines, and power cables to the SBS equipment. Before connecting any equipment, make sure that you are properly grounded, see section Section 2.1.4 “Grounding and Lightning Protection Guidelines” on page 16. 3.2.4.
RB03061201 STRIDE2400 Base Station Installation PTP Radio Backhaul Antenna Connector PTP Radio Backhaul Antenna Cable Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.4.2 Connecting a T1 Cable to the T1Lightning Protection Module The optional T1 Lightning Protection Panel provides up to eight T1 lines that protect the Octal T1 module network interfaces from lightning surges. Requirements: Supplied by Customer: T1 Cables Tools: Phillips screwdriver Guideline: • E Ensure that the SBS power is turned off To connect a T1 line to the Lightning Protection Module 1.
STRIDE2400 Base Station Installation T1 Lightning Protection Panel T1 Lightning Protection Module RB03061801 T1 Rubber Stopper T1 Lightning Protection Module Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.4.3 Connecting DC Power to the SBS The SBS is powered from a DC power source and requires -48 VDC (-40.5 to -57) input voltage. f If you are not providing -48 VDC and have purchased the AC/DC Converter option, please go to Section 3.2.4.4 “Connecting AC Power to the SBS” on page 50.
STRIDE2400 Base Station Installation 7W 1 RB03090302 ROUT ER 2 + Power Input Fitting DC Input Power Cable Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.4.4 Connecting AC Power to the SBS SBS’s powered from an AC power source require the AC to DC Converter. The AC to DC Converter generates 110 VAC to -48 VDC and supports nominal input voltage of 85 VAC to 135 VAC (50/60 Hz). The AC to DC Converter works in conjunction with the SBS Battery Enclosure.
STRIDE2400 Base Station Installation ROUT E R 7W 1 + 2 Black AC ON AC Input Panel RB03090303 Red AC Input Power Cable Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.4.5 Connecting the SBS Battery Enclosure Cable Harness to the SBS The SBS Battery Enclosure backup battery provides eight-hour standby power and one-hour-talk backup time during power interruptions. The SBS Battery Enclosure connects to the SBS’s AC to DC Converter.
RB03090802 STRIDE2400 Base Station Installation AC/DC Converter SBS Battery Enclosure Cable Harness AC Input Panel Battery Fitting Figure 3.
STRIDE2400 Access Network Setup Guide 3.2.4.6 Connecting the SBS Antenna Cable to the SBS The SBS Antenna Cable connects the SBS antenna to the SBS equipment to provide the radio communication in the STRIDE2400 access network.
RB03061901 STRIDE2400 Base Station Installation Antenna Connector RF Lightning Protection SBS antenna Cable Figure 3.
STRIDE2400 Access Network Setup Guide 3.3 Powering Up the SBS Powering up the SBS should only be conducted after the installation and connection of the SBS, SBS Battery Enclosure, and SBS Antenna has been completed. After installing and connecting the SBS, SBS Battery Enclosure and SBS Antenna, the power up procedure must then be conducted.
STRIDE2400 Base Station Installation RB03071103 Power Supply ON BATTERY 30A 32V OUTPUT BATTERY BATT. WARMER UTILITY OUTLET 120/240 VAC UTILITY CONV. 120/240 VAC SIGNAL AC INPUT 120/240 VAC 47-63 Hz 15 A POWER PACK ALARMS 1 2 N L DC OUTPUT 1 2 + - + - PWR CONV.
STRIDE2400 Access Network Setup Guide 3.4 Verifying the SBS LED Status Indicators To ensure that the SBS is functioning properly, verify the SBS LED indicators.
RB03071406 STRIDE2400 Base Station Installation -48 VDC A -48VDC B Output Temperature Indicator Fan ON 59
STRIDE2400 Access Network Setup Guide Controller Module LED State Interpretation Timing/Fault Green (flashing slow) Timing on internal clock Green (flashing fast) Timing on T1 source Red Status on power up Green Module is active Red Module is not active Yellow Status on power up Status Status 60 RB03071402 Timing/Fault
STRIDE2400 Base Station Installation Add/Drop Multiplexer (ADM) Module State Interpretation Status Green Module is active Red Module is not active Yellow Status on power up Status RB03071403 Add/Drop Multiplexer (ADM) Module 61
STRIDE2400 Access Network Setup Guide Data Module LED State Interpretation Status Green Module is active Red Module is not active Yellow Status on power up E1/T1 Not applicable Sych Not applicable FD Yellow Operating in full-duplex mode Off Not operating in full-duplex mode Yellow Connected to a 100Base-T network Off Connected to a 10Base-T network Green Receiving Off Not receiving Green Transmitting Off not transmitting Yellow Ethernet signal detected Off Ethernet signal
Status E1/T1 Sych FD SP RX TX LI COL RB03071401 STRIDE2400 Base Station Installation 63
STRIDE2400 Access Network Setup Guide Octal T1 Module State Interpretation Status Green Module is active Red Module is not active Yellow Status on power up Green Active T1 connection Orange No T1 Link Off T1 not configured E1/T1 Lines 1-8 Status E1/T1 Lines 64 RB03071405 LED
STRIDE2400 Base Station Installation Modem Array Module LED State Interpretation Status Green Module is active Red Module is not active Yellow Status on power up Green Activity on channel Orange No activity on channel Red Channel open but no activity Lines 1-8 Status Lines 9-16 RB03071404 Channels 1 - 16 65
STRIDE2400 Access Network Setup Guide Radio Interface Module State Interpretation Status Green Module is active Red Module is not active Yellow Status on power up Status 66 RB03071501 LED
STRIDE2400 Base Station Installation SBS Radio Module State Interpretation Power On Green Module is active Red Fault Status RB03071502 LED 67
STRIDE2400 Access Network Setup Guide 3.5 Installing the SBS Battery Enclosure The SBS Battery Enclosure houses the batteries to provide eight-hour standby power and one-hour-talk backup time during power interruptions. This section describes the procedures for installing the SBS Battery Enclosure. To install the SBS Battery Enclosure 68 1. Unpack the SBS Battery Enclosure and verify that all components are delivered as described in Section 3.5.
STRIDE2400 Base Station Installation 3.5.1 Verifying the SBS Battery Enclosure Package Contents Verify that you have received the following materials with your SBS main package. If any materials are missing or damaged, please contact SR Telecom technical services. SBS Battery Enclosure SBS Battery (purchased separately) RB03082804 SBS Battery Warmer (optional) - not shown Battery Pack Package Figure 3.
STRIDE2400 Access Network Setup Guide 3.5.2 Mounting the SBS Battery Enclosure The SBS Battery Enclosure can be mounted on a pole or wall. If you are mounting the SBS Battery Enclosure on a pole, install the SBS Battery Enclosure on the side opposite the station to distribute the equipment weight evenly. Type Height Width Depth Weight SBS Battery Enclosure 21.1 in. (43.2 cm) 17 in. (53.6 cm) 13.3 in. (33.8 cm) 105 lb. (47.
RB03061301 STRIDE2400 Base Station Installation SBS Power Pack Mounting Bracket Galvanized Bolts Lock Washer Washer Figure 3.
STRIDE2400 Access Network Setup Guide 3.5.3 Grounding the SBS Battery Enclosure Grounding the SBS Battery Enclosure helps to prevent serious injury to service personnel and avoids damage to the equipment. Requirements: Included with SBS Battery Enclosure: 6 AWG ground wire Tools: Crimping tool, wire cutter/stripper or utility knife Guidelines: E 72 • For pole-mount installations, route the ground wire along the side of the pole opposite to the station’s SBS Antenna Cable.
RB03061601 STRIDE2400 Base Station Installation Ground Studs Ground Lug Washer Keps Nuts 6 AWG Ground Wire Figure 3.
STRIDE2400 Access Network Setup Guide 3.5.4 Connecting the SBS Battery Enclosure Cable Harness to the SBS Battery Enclosure The SBS Battery Enclosure Cable Harness connects to the SBS Battery Enclosure to provide backup power during power interruptions.
RB03091101 STRIDE2400 Base Station Installation WARNING Reversed Polarity may HAZARDOU be S Cable Fitting Connector SBS Battery Enclosure Cable Harness Figure 3.
STRIDE2400 Access Network Setup Guide 3.5.5 Installing the SBS Backup Battery The SBS Battery Enclosure batteries must be charged within its typical storage lifetime period prior to installation; refer to Table 3.1. Table 3.1 Average Ambient Temperature Typical Storage Life 0°C (32° F) to 20°C (68°F) 12 months 21°C (70° F) to 30°C (86°F) 9 months 31°C (88° F) to 40°C (104°F) 5 months 41°C (106° F) to 50°C (122°F) 2.5 months f 3.5.5.
STRIDE2400 Base Station Installation Guidelines: E • Use an adjustable power supply to top charge the battery, SR Telecom equipment must not be used • Do not top charge the battery more than three times during its storage life • Discard the battery according to the manufacturer’s instructions and local laws; always replace the battery with the same or equivalent type To charge the SBS Backup Battery 1. Top charge one battery at a time according to Table 3.2.
STRIDE2400 Access Network Setup Guide 3.5.5.2 Connecting the Battery to the SBS Battery Enclosure The SBS Backup Batteries provide backup power and also serve to filter out voltage spikes that may be present in the AC network. To ensure maximum equipment performance, operate the Battery Enclosure only when its batteries are installed.
STRIDE2400 Base Station Installation Cable Harness WARNING Reversed Polarity may HAZARDO be US WARNING Reversed Polarity may HAZARDO be US Connector RB03090901 Battery Cable WARNING Reversed Polarity may HAZARDO be US WARNING Reversed Polarity may HAZARDO be US SBS Battery Enclosure Figure 3.
STRIDE2400 Access Network Setup Guide
Chapter 4 STRIDE2400 Terminal Station Installation This chapter has been intensionally left out for this review. For information on the STRIDE2400 Terminal Station, refer to the STRIDE2400 Terminal Station Setup Guide, 033-100569-001.
STRIDE2400 Access Network Setup Guide 82
Chapter 5 Your Next Step Return to your STRIDE2400 Access Network Roadmap to continue with the next phase of planning, setting up or managing your STRIDE2400 access network.
STRIDE2400 Access Network Setup Guide
Index C L Cable requirements, 19 Clamps, 26 Concrete, 38 LED verification Add/Drop Multiplexer Module, 61 Controller Module, 60 Data Module, 62 Modem Array Module, 65 Octal T1 Module, 64 Power Supply Module, 58 Radio Interface Module, 66 SBS Transceiver Module, 67 D DC Power, 48 Dimensions SBS, 32 SBS Power Pack, 70 M Environmental requirements, 19, 20 ESD precautions, 15 Mounting SBS, 32 SBS Antenna, 24 SBS Power Pack, 70 G P Ground wire, 28, 42 Grounding Grounding and lightning protection guidel
STRIDE2400 Access Network Setup Guide Installation precautions, 14 Installing, 30 LED verification, 58 Mounting on a concrete base, 38 Mounting on a wooden pole, 32, 34, 36, 40 Mounting requirements, 32 Package contents, 23, 31, 69 Power up, 56 PTP Radio Backhaul, 44 Safety guidelines, 14 Site requirements, 19 T1 Lightning Protection Module, 46 T1 Lightning Protection Panel, 46 Tool requirements, 18 SBS Antenna Grounding, 28 Mounting, 24 Package contents, 23, 31, 69 Tool requirements, 18 SBS Antenna Cable C
