Design Requirements Document Version: 1.0 Last updated December 24, 2018 Copyright © 2018 Sprint Corporation. All rights reserved.
© Copyright by Harman Connected Services, 2018-2019. All rights reserved worldwide. Legal Notices The information contained within this document is proprietary, privileged and intended only for the recipient. As such, the information is subject to all relevant copyright, patent and other laws protecting intellectual property, as well as any specific agreements protecting Harman Connected Services rights in the aforesaid information.
Table of Contents 1. Document overview 5 1.1. Abstract 5 1.2. Security and proprietary information 5 2. Physical Design 5 3. Hardware Specification 5 4. Installation 10 4.1 Unpacking and Checking the unit 10 4.2 Finding the Best Location 10 4.3 Initial Setup 10 Configuration 12 5. 5.1 LTE Installation: 5.1.1 5.1.2 5.1.3 6. Installation Sequence Successful Installation Failed Installation Sprint TREBL Companion App Flow: 12 12 12 12 13 6.1 Launch Screen : 13 6.
6.11.4 6.11.5 6.11.6 6.11.7 7. Notification Amazon Alexa Help About Warning and Cautions 23 24 24 25 26 7.1 Human Exposure to Radio Frequencies 26 7.2 Radio Interference 26 7.3 Modifications 26 7.4 General 26 7.5 Important Safety Instructions 26 7.6 Safety 26 7.7 Service Information 27 7.8 UL Information 27 8. FCC Notice 28 8.1 Federal Communication Commission Notice 28 8.2 Radiation Exposure Statement: 28 9. Maximum Output TX Total Power 29 10.
1. Document overview 1.1. Abstract This purpose of this document is to define the overall Product requirements and design of Sprint’s MagixBox TREBL. This document is meant for Harman, Sercomm and Sprint Internal Teams to understand the Product implementation and requirements and execute them accordingly. 1.2. Security and proprietary information The content of this document is PROPRIETARY INFORMATION of Sprint, Harman and Sercomm .
Category Buttons Note: Buttons will be back lit and will have laser-engraving underneath the top surface.
Zigbee No of Type: Material: Frequency range: 2400 - 2500 MHz ZigBee (802.15.
Frame Type Error Control Channel quality Handover RLC Mode Sync LTE security LTE Network Planning TDD Frame Configuration 1 (DL: UL 60:40) TDD Frame Configuration 2 (DL: UL 80:20) Special Sub-Frame 7 HARQ Enhanced Link Adaptation S1 Seamless Handover X2 Seamless Handover Lossless Handover (Packet Forwarding) RLC-AM RLC-UM RLC-TM Sync from GPS Sync from Network Listen AES Integrity Protection SNOW3G Integrity Protection IPSEC CMPv2 Soft Frequency Reuse (SFR) / Static ICIC PLMN Support (up to six) Handov
Internet Protocol (IP) support IPv4 Support IPv6 Support Max UE’s 16 active UEs WiFi Antenna Gain: >2dBi GPS Antenna Gain: >2dBi GPS Receiver as per spec Load information over X2 Antenna Gain Receiver GPS X2 AP procedure Congestion control Load based scheduling LTE Relay Specification The following table lists the LTE relay specifications: Category Specifications SIM Card Standard SIM Card (3FF) for Lab and MFF2 for production Chipset Info GDM7243A + GRF7243A + QCA8337 Band support: TDD: 41 B41
IPv6 Support Peak UE Throughput DL Mode Yes DL Transmission Frame Type DL=B41/580 Mbit/s , 4CA 256QAM B25/600 Mbit/s (3CA 256QAM) DL Transmission Mode 1 -9 Frame Type 1 FDD Frame Type 2 TDD, 5ms periodicity B41: 4T8R Tx/Rx B25: 2T8R Scanning DeNB Selection and Ranking PDCL --> Donor Selection Algorithm 4. Installation The Sprint TREBL unit is placed on the windowsill to receive the signal from outdoors and boost it indoors.
The Sprint TREBL turns on automatically when the power supply unit is connected to the underside of the unit. 1. Place the Sprint TREBL on a suitable windowsill and verify that the unit’s rear side is positioned against the glass as close to the glass as possible (as in the figure 1 below). 2. Shortly the following will be occurred while the unit is starting up.
5. Configuration After solid white LED pattern Sprint TREBL is looking for sprint network after find the Sprint network following process start 5.1 5.1.1 LTE Installation: Installation Sequence VGI Sound: Sprint TREBL Installation is in progress. Please install the companion app on your mobile or tablet LED Pattern: 5.1.
6. Sprint TREBL Companion App Flow: 6.1 Launch Screen : Launch screen shows Sprint TREBL Logo while launching the APP. It is the first screen after launch APP and it appears for 2-3 second to user 6.
6.2.1 Welcome Screen : Welcome screen appears after launch screen that provide a message to user Sprint TREBL help to boost your network and improve the connectivity experience. 6.2.2 Sound by Harman/Kardon: After tap on next button in welcome screen or swipe left Sound by Harman/Kardon screen Appears which provide the message to user that Harman Kardon Speaker Integrated in Sprint TREBL and user can enjoy the music after connected from the bluetooth. 6.2.
6.4 Connection Flow After accepting Terms and condition user enter on the connection flow to connect Sprint TREBL to companion App Connection Flow to Connect Sprint TREBL Connection flow user navigate from three screen 6.4.
6.4.2 Setup Mode On: After tap on continue button user navigate to Setup Mode on Screen which provide a message to user how to identify that the setup mode is enable or not by checking to and fro motion of blue light. 6.4.3 TREBL Connection: After tap on continue button of Setup Mode On Screen user navigate to TREBL Connection Screen which provide the SSID (HK TREBL-XXX) information of Sprint TREBL to user so user can identify Sprint TREBL in Wi-Fi List. 6.
6.7 LTE Installation 6.7.1 LTE Installation progress After tap on Continue button in device connected screen.
Installation in progress Installation Complete 6.7.2 Installation Failed : if any issue occurred during installation user navigate to installation failed Screen. 6.
When user select any Wi-Fi . user need to enter password if the Wi-Fi is protected, for open Wi-Fi it configure directly and after successful Wi-Fi configurartion. user navigate to Alexa entry screen which is option to user configure Alexa .
6.
Mockup screen provide the information of for following Dashboard button functions . Side menu Notifiaction Change Login 6.10 DashBoard When user tap on got it button on Mock screen Dashboard appears. Which provide the following status of Sprint TREBL TREBL Connection Status Network Setting option Amazon Alexa 6.
Help About 6.11.1 Dashboard When user tap on Dashboard it re- direct to Dashboard screen. this option is selected by Default 6.11.
6.11.3 Network Setting When user tap on Network setting it re direct to Network Setting screen 6.11.
6.11.5 Amazon Alexa When user tap in Amazon Alexa option it redirects to Alexa entry screen. if Alexa is already configured it shows Alexa logout popup. 6.11.
6.11.7 About When user tap on About it shows the current version of APP and build number.
7. Warning and Cautions 7.1 Human Exposure to Radio Frequencies The Sprint TREBL antennas should be installed with a minimum distance of 20 CM from your body. 7.2 Radio Interference This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to internal vehicle radio communications. Please ensure a maximum separation between the Sprint TREBL antenna and other antennas. 7.
o Static sensitive components inside - do not remove the lid or base: No user serviceable parts inside. o Position the power cord to avoid possible damage; do not overload circuits. o Do not place this product on or near a direct heat source and avoid placing objects on the terminal. o Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect the power before cleaning. o It is the user’s responsibility to install this device in accordance with the local electrical codes.
8. FCC Notice 8.1 Federal Communication Commission Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
9. Maximum Output TX Total Power Table 1: Sprint Magic Box Gold eNB FCC Maximum Output TX Total Power Caution: Do not set maximum output TX power to higher than local regulations.
10. Power Consumption Antenna Usage Sprint Magic Box Gold unit has four (4) RF ports that are connected to two (2) dual-port antennas arrays. Each antenna array is mounted on opposite sides internally within the Airspan product housing. This is so that one antenna array faces forwards and one antenna array faces outwards for optimized coverage.
11. Customer Care Help Desk Sprint Customer Care Help Desk offers prompt and efficient customer support services. To create and update issue logs, send e-mails to Customer Care Help Desk. Once you submit your issue, the system generates a new issue and sends an issue number for your reference. The system uses this issue number to categorize and store e-mails under the appropriate issue.
12. Management Software is upgraded locally and remotely. Designed for local and remote management 11. Sprint TREBL 11.1 Physical Dimensions H X W X D = 205.99 mm X 199.87 mm X 199.87 mm Weight: ~4.5 Kgs. 12.1 eSIM Card The Sprint TREBL provides an embedded eSIM and a standard SIM card holder for the operatorprovided SIM, (installed during assembly). 11.
13. Hardware Security 13.1 Factory Generation of Device Key Each device has a private key and associated certificate which is used to authenticate itself when initiating communications. This private key is generated in the factory, and so is the corresponding vendor certificate. This capability necessary in order to support large scale plug and play deployments. This device key is stored on the Sprint TREBL to allow it to authenticate to the network.
