2.4 GHz Stamp User’s Manual Part Number 9100-0160-01 Revision 1.0 Date: October 4, 2006 Axonn LLC Stamp User’s Guide-Document #9100-0160-01 Ver 1.
Table of Contents 1. 2.4 GHz Stamp Product Description………………………………………… 2. Typical Integration…………………………………………………………… 3. Product Specifications………………………………………………………... 3.1 Specifications……………………………………………………………… 3.2 Pin Diagram……………………………………………………………….. 3.3 Pin Descriptions……………………………………………………………. Air Interface………………………………………………………………….... 4.1 Frequency………………………………………………………………….... 4.2 Power………………………………………………………………………. 4.3 Timing……………………………………………………………………… 4. 5.
1. 2.4 GHz Stamp Product Description To be completed 2. Typical Integration Below is a block diagram of how a normal system using a 2.4 GHz Stamp would be designed. 3. 3.1 TBC Product Specifications Specifications Axonn LLC Stamp User’s Guide-Document #9100-0160-01 Ver 1.
3.2 3.3 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Pin Diagram Pin Descriptions Pin Name Electrical Spec GND Reset DO NOT CONNECT VRF 3.3V +/-5% GND VDIG 3.3V +/-5% RF RX 3.3V TTL Output Logic 0: <0.6V Logic 1: >0.8*Vdig Test In DO NOT CONNECT NC GND NC NC RF TX 3.3V TTL Input Logic 0: <0.6V Logic 1: >0.8*Vdig GND GND Axonn LLC Note Tie directly to host ground plane. For use with serial programming Powers the 2.4 GHz transceiver Powers digital circuitry Data Input To be transmitted over 2.
Approximate Current Consumption (through Vdig and Vrf combined): Maximum: 25mA Sleep mode: 1-2µA 4. Air Interface TBC 4.1 Frequency TBC 4.2 Power TBC 4.3 Timing TBC 5. Serial User Interface TBC 5.1 Message Protocol TBC 5.2 Tips TBC 5.3 Timing TBC 5.4 Digital I/O TBC Axonn LLC Stamp User’s Guide-Document #9100-0160-01 Ver 1.
. Mounting Guidelines The figure below shows the recommended footprint for mounting the Stamp on its host board. 7. TBC Power Supply Requirements 8. TBC Environmental Specifications Axonn LLC Stamp User’s Guide-Document #9100-0160-01 Ver 1.
9. Regulatory Approvals FCC ID: L2V-STAMP IC:3989A-STAMP THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Axonn LLC Stamp User’s Guide-Document #9100-0160-01 Ver 1.
The FCC requires the following notification for the device in compliance with 47CFR 15.105 for this Class B digital device. Full product test reports are available from Axonn upon request. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment.
This ClassB digital apparatus complies with Canadian ICES-003. This device will operate in accordance to the standards set forth by the CE Mark Directives and standards R&TTE: ( EN 300 328), RFI: (EN61000-4-3:1996 + A1:1998 + A2:2000), ESD: (EN61000-4-2: 1995 + A1:1998) NOTICE: This equipment complies with the FCC RF Exposure Limits. A minimum of 20 centimeters (8 inches) separation between the device and the user and all other persons should be maintained.