User's Manual

ManualsBrandsSpiderCloud Wireless ManualsElectronicsSpiderCloud Radio Node

SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide

SpiderCloud Wireless, Inc.

Figure 12 Fully Mounted

Installing the Radio Node (Method 2)

To route the cable directly and mount the radio node

Step 1 Route the Ethernet cable through the large hole in the mounting bracket.

Figure 13 Mount Bracket with Direct Cable Routing

Step 2 With two user-provided screws, attach the mount bracket assembly to a wall or ceiling. The

screw holes are sized for an M4 (#10) screw. Ensure the screws have a snug fit onto the

studs, sheetrock, anchor, or other material you are bolting onto.

Step 3 Insert the RJ-45 connector into the Ethernet port as shown in Figure 14:

Transmit Side

Summary of content (14 pages)

PAGE 1
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Figure 12 Fully Mounted Installing the Radio Node (Method 2) To route the cable directly and mount the radio node Step 1 Route the Ethernet cable through the large hole in the mounting bracket. Transmit Side Figure 13 Mount Bracket with Direct Cable Routing Step 2 With two user-provided screws, attach the mount bracket assembly to a wall or ceiling. The screw holes are sized for an M4 (#10) screw.
PAGE 2
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide RJ-45 Connector in Ethernet Port Figure 14 Route and Terminate the Cable Step 4 Push as much cable back through the wall or ceiling as possible. The mount bracket assembly has room for some cable slack. Step 5 Slide the pedestal base of the radio node into the groove opening in the mount bracket. When the pedestal reaches the end of the trough, a spring clip will secure the unit into place.
PAGE 3
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Completing the Installation Step 1 Attach a padlock or cable tie wrap through the cutout lock holes in the mount bracket and pedestal base. Figure 16 Padlock and Lock Holes The lock in the above figure is shown schematically. The orientation is for illustration purposes (not accurate) since the bracket is typically wall or ceiling mounted. Step 2 The radio node boots up and attempts to connect to the services node.
PAGE 4
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Boot Sequence and Services Node Communication On initial boot, the radio node performs the following boot sequence and communicates with the services node. It performs this boot sequence twice, first for the UMTS subsystem, then again for the LTE subsystem. This sequence takes about one minute to complete for each subsystem. When finished, all devices are reachable.
PAGE 5
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Radio Node LED Boot Sequence The radio node state machine is sequential and progresses in the following order: State 0 -> State 1 -> State 2 -> State 3 -> State 4 -> State 5 A normal boot sequence transitions through all these states sequentially and the LED state transitions accordingly. If the radio node fails to transition to the next state, the system restarts the boot sequence, starting with State 0.
PAGE 6
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Table 3: Radio Node LED Boot Sequence (continued) State 3. TFTP LED Color Flashing Blue Description Possible Failures and Actions The radio node proceeds next to download the operating system image from the services node. The radio node moves to the next state (State 4) after the image has been downloaded. 4. Operating System Booting Flashing Green The radio node loads the operating system and starts the default platform applications.
PAGE 7
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Table 4: Radio Node LED Behavior (continued) LED Status Blue: fast flashing Locate radio node enabled* Blue: solid Follow IMSI enabled* Off Powered off or LED disabled Flash Rate Approximately 1 second on/off cycle * Refer to the SpiderCloud OS (SCOS) Administrator Guide for information about the locate radio node and follow IMSI features.
PAGE 8
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide The SpiderCloud Documentation Set The SpiderCloud documentation set includes: • The SpiderCloud System Description provides an overview of how the SpiderCloud system fits within an operator’s network and in an enterprise, describes key features of the system, and provides specifications for the services and radio nodes.
PAGE 9
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Appendix A: UMTS Antenna Patterns 0º UMTS Band Antenna Patterns 90º Up Front 0o 3 dB -30o 30o 0 -3 -6 -60o 60o -9 -12 -15 90º -90o 9 0o -15 0º -12 -9 -6 -120o Front 120o 90o 3 dB 120o -3 0 -150o 60o 0 -3 150o 3 dB -6 150o 180o AUT = 2140 MHz : Max Gain = 2.59 dBi at 90 o 1 30o -9 1 AUT = 2140 MHz : Max Gain = -0.
PAGE 10
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide PCS Band Antenna Patterns 0º 90º Up 0o Front 3 dB -30o 30o 0 -3 -6 -60o 60o -9 -12 -15 -90o 9 0o 90º -15 -12 0º -9 -6 -120o 120o -3 90o Front 3 dB 120o 0 -150o 60o 0 -3 150o 3 dB -6 150o 180o AUT = 1960 MHz : Max Gain = 4.
PAGE 11
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide DCS Band Antenna Patterns 0º 90º Up Front 0o 3 dB -30o 30o 0 -3 -6 -60o 60o -9 -12 90º -15 -90o 9 0o 0º -15 -12 -9 90o Front -6 -120o 3 dB 120o 120o -3 0 -150o 60o 0 -3 150o 3 dB -6 150o 30o -9 180o -12 AUT = 1844 MHz : Max Gain = 3.55 dBi at 54 o 1 1 -15 AUT = 1844 MHz : Max Gain = 0.
PAGE 12
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide 26 SpiderCloud Wireless, Inc.
PAGE 13
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide Appendix B: LTE Antenna Patterns LTE Band 4 Antenna Patterns 0º Up 90º Front 0o 3 dB -30 o 30 o 0 -3 -60 o 60 o -6 -9 90º -12 90 o Top -90 o -12 0º -9 -6 -120 o Front 120 o -3 90o 0 o -150 o 3 dB 3 dB 120 150 o 60o 0 180 o -3 150o EL1 Cut (Front-to-Back) 30o -6 -9 -12 180o 0o -12 0º -9 -6 Up -150o 90º -30o -3 0 0o -30 o 3 dB -120o 30 o 3 dB -60o -90o 0 AZ Cut -3 -60 o 60 o -6 -9 -12 -90 o
PAGE 14
SpiderCloud Radio Node - SCRN-310 Hardware Installation Guide LTE Band 7 Antenna Patterns 0º Up 90º 0o Front -30 o 3 dB 30 o 0 -3 -60 o 60 o -6 -9 -12 90º -90 o 90 o Top -12 -9 0º -6 -120 o 120 o -3 Front 90 0 -150 o 3 dB 3 dB 120 o 150 o 60 o 0 180 o -3 150 o EL1 Cut (Front-to-Back) 30 o -6 -9 -12 180 o 0o -12 -9 0º -6 -150 o Up 90º 0 -120 o 0o -30 o -30 o -3 3 dB -60 o 3 dB -90 o 30 o AZ Cut 0 -3 -60 o 60 o -6 -9 -12 -90 o 90 o -12 -9 -6 -120 o